Construction of Micro Composting Centres in Namakkal District under SBM (G) Package 1

Amount

Construction of 1.0 MT (capacity) Micro Compost Centre (MCC) Muthugapatty H/O Muthugapatty

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Lowering the 50mm dia GI Pipe into the trenches by proper alignment and gradient including all labour charges and fixing charges etc,complete as per standard specifications.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

GEO Physical investigation charge

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of 7.50 HP borewell three phase submercible pumpset 50 lpm X 225 head including all labour charges

Construction of 0.70 MT (capacity) Micro Compost Centre (MCC) Reddipatty H/O Reddipatty

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Lowering the 50mm dia GI Pipe into the trenches by proper alignment and gradient including all labour charges and fixing charges etc,complete as per standard specifications.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

GEO Physical investigation charge

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of 7.50 HP borewell three phase submercible pumpset 50 lpm X 225 head including all labour charges

Construction of 0.70 MT (capacity) Micro Compost Centre (MCC) Pottireddipatty H/O Pottireddipatty

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Lowering the 50mm dia GI Pipe into the trenches by proper alignment and gradient including all labour charges and fixing charges etc,complete as per standard specifications.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

GEO Physical investigation charge

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of 7.50 HP borewell three phase submercible pumpset 50 lpm X 225 head including all labour charges

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Lowering the 50mm dia GI Pipe into the trenches by proper alignment and gradient including all labour charges and fixing charges etc,complete as per standard specifications.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of 10 HP borewell three phase submercible pumpset 50 lpm X 250 head including all labour charges

Supply and delivery of 3 phase panel board with two level guard and auto start including cost and conveyance of all charges etc. complete panel board

40 MM GI pipe

40 MM GI pipe

Supply of 4.00 sqm cable including cost and conveyance of all charges

Supply of bore well cover

Laboir charges for the errection of submiersible pumpset in borewell / openwell including fixing and jointing submersible cable with proper clams upto the starter to requied depth and also fixing of riser etc .

Construction of 0.70 MT (capacity) Micro Compost Centre (MCC) Selllappam patti

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

GEO Physical investigation charge

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of 7.50 HP borewell three phase submercible pumpset 50 lpm X 225 head including all labour charges

Construction of 0.70 MT (capacity) Micro Compost Centre (MCC) Ramanaickenpatty H/O Pachal

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Lowering the 50mm dia GI Pipe into the trenches by proper alignment and gradient including all labour charges and fixing charges etc,complete as per standard specifications.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

GEO Physical investigation charge

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of 7.50 HP borewell three phase submercible pumpset 50 lpm X 225 head including all labour charges

Construction of 0.70 MT (capacity) Micro Compost Centre (MCC) Marapparai

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc., complete - Open Earth work Excavation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111, 112, 401, 900

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete as directed by departmental officer etc., complete. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using III class Country bricks of size 8 3/4"X41/4"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4"X41/4"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Dadooing walls with Glazed tiles of sizes 200mm X600mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings and labour charges, inclusive of fixing lowlevel flushing tank and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing the glazed S W pipes of 100mm size of approved quality with spigot and socket ends in dry condition with spun yarn and cement joints required depth for tranches including petty masonry,shoring and strutting wherever found necessary, and laying the pipeline in the alignment at the specified gradient and testing with necessary tools and plant etc. and levelling the ground complete complying with standard specifications.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm dia,PVC pipe

25mm dia.PVC pipe

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I Bend

20mm dia G.I union

25mm dia G.I coupling

25mm dia G.I Tee

25mm dia G.I Elbow

25mm dia G.I Bend

25mm dia G.I union

20mm X 15mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Elbow

25mm X 20mm dia G.I Reducer

20mm X 15mm dia G.I Reducer Tee

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Door Elbow

110mm dia PVC Door Tee

90mm dia PVC Elbow

90mm dia PVC Tee

90mm dia PVC Door Elbow

90mm dia PVC Door Tee

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

90mm dia PVC 6KSC Pipe

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply and Delivery of 50mm dia G.I. Pipes of approved quality and best varity 50mm dia size as per IS 1239/ Part I /90 . The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Lowering the 50mm dia GI Pipe into the trenches by proper alignment and gradient including all labour charges and fixing charges etc,complete as per standard specifications.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Borewell and water supply arrangements

GEO Physical investigation charge

Drilling borewell in hard rock area including labour charges

Drilling of 150 mm dia borewell upto casing pipe

Drilling of 150 mm dia borewell beyond casing pipe

Supply and delivery of PVC (ISI) casing pipe suitable for 150 mm dia borewell including cost of all labour charges etc

Supply and delivery of PVC (ISI) borwell cover

Supply and delivery of 7.50 HP borewell three phase submercible pumpset 50 lpm X 225 head including all labour charges

GST Amount for providing Service to Government Contract Works for the above RENEWAL Works. { GST Amount is the Total GST Amount for overall quoted amount above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

P R and Co