Balance work of Facelifting and Protection work of CFC building at Maali Pyt. Plakh

Earthwork in excavation by mechanical means (Hydraulic excavator) in trenches for foundation, drains, pipes etc. (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding 10sqm on Plan, including dressing of sides and ramming of bottoms lift upto 1.5m, including getting out the excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 mtr. a) All Kind of soil.

Providing and laying cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work upto plinth level with: a) 1:5:10 (1 cement:5 coarse sand:10 graded stone aggregate 40mm nominal size).

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: a) 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) with 20% boulders.

Centering and shuttering including strutting propping etc. and removal of form work for:- a) Foundations, footings, bases of columns etc. for mass concrete.

15mm cement plaster on the rough side of single or half brick wall of mix. 1:6 (1 cement: 6 fine sand).

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:6 (1 cement:6 coarse sand).

Extra for brick work with common burnt clay bricks / cement concrete bricks in superstructure above plinth level upto floor five level.

Providing and fixing 35mm glazed shutters for doors, windows and clerestory windows using 4mm thick float panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. A) Second class deodar wood.

Providing and fixing 30mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : a) Second class deodar wood

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc consisting of following operations. a) Applying a slurry coat of neat cement using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineerin-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) finishing the surface with 20mm thick joint less cement mortar of mix 1:4(1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm/sq 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineerin-charge. 23.7.1 With average thickness of 120mm and minimum thickness at khurra as 65 mm

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. a) Float glass panes: i) 4 mm thick glass pane (weighing not less than 10 kg/sqm)

Finishing walls with Acrylic smooth exterior paint of required shade: a) Old work (one or more coats applied @ 0.90 liters/ 10sqm)

Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete.

Sand from Billawar for an av. lead of 50.00 km. by M.T.

Stone aggregate (Crusher bajree) below 40mm nominal size from Billawar for an av. lead of 50.00 km. by M.T.

Stone aggregate 40mm nominal size & above from Billawar for an av. lead of 50.00 km. by M.T.

Stones / boulders from local nallah for an av. lead of 5.00 km. by M.T.

Brick from Kathua for an average lead of 80.00 Km. by M.T.