PROVN OF VEHICLE PARKING SHED, FOL STORAGE SHED AND OTHER SANCTIONED WORKS AT DIFFERENT LOCATIONS OF AGE BR P UNDER GE 861 EWS

Amount

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

RCC M-25 design mix using 20 mm graded aggregate in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc basements slabs under rammed piles and mass concrete complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate as in beams, cantilevers, bressummers lintels over 1.5 m span complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate in column, pillars, piers, posts and struts complete all as specified and directed.

Form work to sides and soffits of floor or roof beam haunching , lintels, cantilevers shelved including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finish surface of concrete square, rectangular or polygonal complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

MS TMT Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders, cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed.

Hard core of broken stone or boulders of guage exc 63mm but n. exc 100mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Walling of random rubble masonry with best quality stone, uncoursed, well bonded, bedded and solidly hearted and built in CM 1:4, all as specified.

Precast cement concrete type C-1(using 16mm graded crushed stone aggregate) hollow block masonry with solid blocks exceeding 10cm in width and setting in mortar 1:6, complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:4, complete all as specified and directed.

Providing precast cement concrete louvers and jallies, 35mm thick, type B-0 (1:2:4) 12.5mm graded aggregate, (measured solid), including all mouldings but excluding frame, set in CM 1:4, complete all as specified as directed.

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement including mixing of water proofing compound in the proportion as mentioned in manufacture's instructions complete all as specified. Note: Water proofing compound shall be measured and paid for separately.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint camouflage pattern over a coat of alkali-resistant priming coat, complete all as specified and directed.

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

Preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding (eaves board) to wall fixed with self tapping screws as specified and directed.

6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

2nd class soft wood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 13 Sqcm but n exc 25 Sqcm complete all as specified and directed.

75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub base of floor, complete all as specified and directed.

25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Chequered coloured cement concrete tiles of size 300 x 300 x 25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

Glass ventillators using 5mm thick plain glass and using aluminium powder coated sections conforming to catalogue of 'Jindal' or of equivalent make and rubber beading etc, complete all as specified and directed. (a) SP-20048 (b) Glazing clips-19352.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

100 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

Vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets and including 32mm dia PVC waste pipe, complete all as specified and directed.

15mm bore pillar tap, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

32mm dia waste coupling of PTMT (half or full threaded) suitable for urinals, complete all as specified and directed.

Vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, jointing to flush pipe complete and making good in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed .

10 litre capacity PVC valveless, low level, syphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

32mm dia PVC waste pipe suitable for wash hand basin, complete all as specified and directed.

Steel water tubing, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

15mm bore bib tap, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,complete all as specified and directed.

15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

Fancy type CP brass soap dish, complete all as specified and directed.

Grating square 150mm size of PTMT (minimum weight 100grams), complete all as specified and directed.

110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) bends, complete all as specified and directed.

110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

110mm bore PVC (SWR) reducers, complete all as specified and directed.

75mm bore pipe PVC (SWR) vent cowl and fixed, complete all as specified and directed.

75mm bore dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed.

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 20mm dia with iron wheel head, both ends screwed for iron pipe complete all as specified and directed.

Construction of septic tanks, exc, in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fiber reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 100 users complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 1/3, 2/3.

Construction of soakage well for users, excavation in ordinary soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber chamber screen chamber, brick work CM 1: 4, RCC cover slab in M-25/ RR masonry filling with brick bats, complete of size 1.20m dia 3.0 m deep as shown in drg complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 3/3.

Plain cement concrete bed 1:3:6 type C-2 (using 40mm graded crushed stone aggregates)to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipe, complete all as specified and directed.

Precast cement concrete type 1: 2: 4, type-B1 (20 mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set and jointed in CM 1:4, complete all as specified and directed.

PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface channel and drains, complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200 mms thick (Horizontal or sloping), finishing rought the concrete surfaces, complete all as specified and directed.

Surface dressing not exceeding 30 cm deep and averaging 15 cm getting out in hard/dense soil, complete all as specified and directed.

Excavation over areas not exc 1.5m depth and getting out in soft/loose soil, complete all as specified and directed.

All as per srl item No-72 here in above, depth exc 1.50m but not exc 3.0m, complete all as specified and directed.

All as per srl item No-72 here in above, depth exc 3.0m but not exc 4.50m, complete all as specified and directed.

RCC M-25 (Design Mix) using 20mm graded crushed stone aggregate as in retaining walls, basement walls, ballast walls & the like any thickness; above top of footing , complete all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified.

100mm thick, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors, complete all as specified and directed .

40mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors, complete all as specified.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Steel rolling shutters, without ball bearing,as specified including top cover, anchoring rod,hasp and staple and one shop coat of primer; erected in position as indicated in position as indicated ,complete, but gear operated type with bevel gear box and crank handle(thickness of laths in mm=1.25mm), complete all as specified and directed.

Rolled mild steel in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1998 Gd St-240 complete all as specified and directed.

Preparation of surfaces of any description wood, steel, iron, concrete, brick, stone, etc., exceeding 10cm in width or girth and applying one coat of black bituminous paint, complete all as specified and directed.

Rolling over hard core surface with 8 to 10 tonne power roller n exc 150mm compacted thickness, complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc. 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m, in hard/dense soil and making good surfaces, complete all as specified and directed

PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

Mild steel work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed.

Preparation of surfaces treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each with tar or coal tar black paint, complete all as specified and directed.

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Preparation of new plastered surfaces of wall to receive 3mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash,complete all as specified and directed.

Preparation of new plastered surfaces of wall to receive 3mm thick wall care putty and applying two coats of cement base paint over a coat of primer, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, including hacking out old glass panes, complete all as specified and directed.

Forming of 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'B' in 100mm thick flooring, complete all as specified and directed.

Supply only integral water proofing compound of approved quality, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed.

Taking down shutters of any description not exceeding 1.00 Sqm each, and removing from site, complete all as specified and directed

Taking down shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each, and removing from site, complete all as specified and directed

2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

75 mm long, mild steel cold rolled Butt hinges, medium weight, complete all as specified and directed.

100mm long, aluminium alloy handles, cast type, anodised, all as specified and directed.

35mm thick second class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

30mm thick second class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of sash bars and framing moulded, and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b); supplied and fitted to chowkhats, complete all as specified and as directed.

35 mm thick flush doors shutter, solid core construction with block board core and plywood face panels commercial type on both side, lipping with 2nd class hard wood beads, complete all as specified and directed.

150mm long, aluminium alloy handles, cast type, anodised, all as specified and directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm & fixed with tinned tacks or galvanised wire staples in repairs, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm & fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

2nd class soft wood, as in scantlings and similar work, clean sawn, timber framed and fixed in position, complete all as specified and directed.

2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

2nd class soft wood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 3 Sqcm but n exc 6 Sqcm complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets etc, complete all as specified and directed.

Viterous china, wash hand basin, (white) of size 550 mm x 400 mm including PVC waste coupling 32 mm dia with long screwed shank and fly nuts, PVC medium grade 32 mm dia waste pipe, chain and plug, porcelain stopper, PVC connection 15 mm dia, 450 mm long with PTMT nuts and washers at both ends and 15mm bore stop valves, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repair) , complete all as specified and directed.

Earth filling under floors, spreading and levelling in layers n.exc 25cm thick, well rammed including watering as required, complete all as specified and directed.

Vitreous china twin action wash down water closet pan (pedestal pattern), coloured, including fixing bolts, flushing cistern and flush pipe & making good to dismantled/damaged floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.

PVC connection 15mm size with PTMT nuts of length 900mm, complete all as specified and directed.

Vitreous china, fancy type, wash hand basin pedestal type, coloured, size 580x450mm including CP waste coupling and waste pipe fixed over RCC slab, complete all as specified and directed.

15mm chromium plated basin mixture, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with long screwed shanks and flynuts, screwed for iron pipe and fixed, complete all as specified and directed.

Sheet glass shelf assembly 12cm wide consisting of 5.5mm thick glass with CP bracket guard and railing 60cm long, complete, all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, complete all as specified and directed.

Salt glazed stoneware (SGSW) grade 'A' drain pipes 150mm bore laid and jointed on concrete bed including testing etc, complete all as specified and directed.

Fancy type center hole WHB brass CP mixture for mixing hot & cold water screwed down for iron pipe 15mm dia bore and fixed, complete all as specified and directed.

Health faucet, CP brass handjet shower 15mm bore dia and 1500mm long CP pipe, complete all as specified and directed.

CP brass toilet paper holder, fancy type, complete all as specified and directed.

CP brass tubular towel rail, fancy type, 20mm dia and 60 cm long between flanges, complete all as specified and directed.

15mm bore angle valve, CP brass, fancy type, screwed down for high pressure screwed for iron pipe or union etc, complete all as specified and directed.

Fancy type CP brass soap dish, complete all as specified and directed

Fancy type corner glass shelf of size 200mmx 200mm x5.5mm thick glass with CP Railing, complete all as specified.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples,complete all as specified and directed.

Construction of septic tanks, exc, in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fiber reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 05 users complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 1/3, 2/3.

Construction of soakage well for users, excavation in ordinary soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber chamber screen chamber, brick work CM 1: 4, RCC cover slab in M-25/ RR masonry filling with brick bats, complete of size 1.20m dia 1.50m deep as shown in drg complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 3/3.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

2nd class soft wood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area n.exc 3 Sqcm, complete all as specified and directed.

CP brass wall mixer, fancy type for mixing hot and cold water with telescopic shower, screwed down for iron pipe 15mm dia bore, complete all as specified & directed.

Point wiring with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl necessary fittings & fixture and to be turminated in sunk cast iron/pressed steel/PVC terminal boxes for mounting switches, sockets, regulators etc with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch, complete all as specified and directed.

All as per srl item No-142 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

All as per srl item No-142 here in above but for one 5A socket outlet on the same board controlled by one switch.

All as per srl item No-142 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead.

Switch piano flush button types 5/6 Amp, single pole, one way complete all as specified and directed.

Switch socket combination 2 in 1, outlet 5 pin, 5 Amp flush type, universal, complete all as specified and directed.

Switch socket combination 2 in 1, 5/6 pin, 5 and 15 Amp, flush type universal complete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings, complete all as specified and directed.

Supply, installation, testing and commissioning of decorative ultra slim linear LED in replacement of 18 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube all as specified and directed. Make : Havells Cat Part No LHEXBLP7PN1W018 or Equivalent in C&S/Bajaj/Halonix.

Supply & fixing LED bulk head fitting 9 W in engineering plastic housing with clear prismatic diffuser, including LED lamp and all accessories for fixing on wall, complete all as specified and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed.

Sheet metal enclosures distribution board, single pole and neutral 8 way with 200 Amps rated bus bar 240 V, double door IP-42 protection, fixed on wall duly groted in solid block wall or n wooden board with electrical connection and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

MCB, DP (Double Pole), AC, 240 volts, B series capacity 20 Amps to 32 Amps 10kA and making connections complete all as specified & directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by 25%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Exhaust fan 230mm to 250mm sweep PVC body with louvers, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material complete all as specified and directed.

Supply and laying or fixing or passing through pipe or binding with fencing/pole etc, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 Sq mm nominal cross section 2 core all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings with 9W LED lamp, complete all as specified and directed.

M/S Sofi Brothers

M/S BHAT CONSTRUCTION AND BUILDERS

M/S BILAL AHMAD BHAT

M/S NEW JOHAN TRADERS

M/S Tantray and Co