REPAIR/ REPLACEMENT OF UNSERVICEABLE WATER SUPPLY ACCESSORIES INCLUDING CONNECTED WORKS UNDER GE (U) BATHINDA

Amount

Dismantling for repair of existing un-serviceable / worn out bridge wheel assembly complete, worn-out Bevel / Drive gear of Bridge wheel structure and including lathe work if required by transporting to workshop defective worn-out crown wheel of agitator of outer dia 600mm / 100 mm and inner dia 65 mm / 35 mm and No. of teeth 72/18, defective gear box of Bridge wheel assembly strip opening of gear box of ratio 50:1 for repairs, repairing of gear box such as cleaning, tightening of gear including shaft oil seal, wheel seal oil, bearing set of 22217K. set of two complete including nuts, bolts , washers and key etc at site with accessories and reassembling / refixing the same after repairs. Agitator assembly and reassembling floculator bridge structure and keeping aside on jack and removing of defective central bearings and mounting of bridge structure on its original position,including oiling , greasing as per site requirement,Repairing,reassembling and making functionable complete system in all respect including testing and commissioning on load complete all as directed by Engr-in-Charge. Note:-(i) The parts covered under serial itrem No. 02 to 12 of BoQ if required then only shall be replaced and measured and paid as supply only. (ii)The fixing element of Labour of serial itrem No. 02 to 12 is included in this item and nothing extra shall be paid on this account. (iii) The Rate of Lathe work complete all as per original pattern and other fixing arrangments with nut and bolts washers etc. of these items are also included in this item and nothing extra shall be paid on this account.(iv) The rate of transportation from site to workshop & Back is included in this item and nothing extra shall be paid on this account.

Supply only new cast iron bridge wheel of 200 mm dia and 150 mm wide long complete all as directed.

Supply only new shaft made out of mild steel of size 80 mm dia and 700 mm long complete all as directed.

Supply only new key/pin complete all as directed.

Supply only new ball bearing No.22217K.( Set of Two ) as per existing Make: SKF/NBC/FAG complete all as directed.

Supply only steel chain for clarifier of size 32 mm x 20 mm x 2.50 mtr long complete all as directed.

Supply only worm wheel of gear box (50 : 1) ratio made of phosphorus bronze complete all as directed. Make.Shanti Gear/ ELECON

Supply only centre worm shaft of gear box of ratio 50:1 complete all as directed. Make: Shanti Gear.

Supply only of MS Shaft of agitator of size 65 mm dia, 60 cm long as per oringal Pattern complete all as directed.

Supply only of housing having cast iron bush for bearing as per oringal Pattern complete all as directed.

Supply only thrust bearing No 51213 including bush complete all as directed. Make- SKF/ NBC/FAG

Supply only ball bearing No 6015 including bush complete all as directed. Make- SKF/ NBC/FAG

De-silting and cleaning the back wash channel of filtration plant of depth not exc. 2.00 metre and removing silt 50.00 metre away from outer edge of channel of the filtration plant No. 01 and 02 complete all as directed by Engr-in- Charge.

All as per serial item No. 13 above but for the filteration Plant No. 03

All as per serial item No. 13 above but for the filteration Plant No. 04

Dewatering/bailing out muddy staganated water manually or with the help of non clogging pumping sets removing mud from floculator (25 mtr outer dia , 3 mtr depth) upto Filter bed with the help of bucket and rope and removing upto 100 mtr away from the periphery of the floculator, Removing of scraping algae from wall & floor of floculator with wire brushes, steel patti etc, cleaning the same and treating the surface with two coats of white wash and removing soil upto 50 mtr away from outer periphery of the installation, Removing or scrapimg , algae from steel surfaces scraper blades etc in the floculator with wire brushes steel patti and emery paper including treating the steel surfaces with two coats of black anti corrosive paint edible complete all as directed by Engineer-in-charge. Note : (i) The expenditure for removing of mud,cleaning of surface,painting etc involved in complete system of floculator and channels upto filter bed shall be included in the quoted rate and nothing extra shall be paid on this account. (ii) Contractor shall provide all necessary arrangements such as Lighting , Non clog Pumps,ladder etc and will make good to disturbed surface with out any extra cost to the department on this account.

All as per serial item No. 16 above but from floculator (20 mtr outer dia , 3 mtr depth).

All as per serial item No. 16 above but from floculator (22 mtr outer dia , 3 mtr depth).

Dewatering/bailing out muddy staganated water manually or with the help of non clogging pumping set from Sludge tank of size 27 X 27 metres at top and 8 x 8 meters at bottom 3 mtr deep, Removing silt from Sludge tank manually by bucket and rope depth exceeding 4.0 mtr but not exceeding 6 mtr and depositing where directed by Eng-in- Charge at a distance exe 50 mtr away from outer wall of installation.Cutting existing bushes/herbs/unwanted plants, Scrapping out silt, algae etc from side walls and floor by washing, cleaning the same with steel wire brush ,brooming etc and washing the side walls with bleaching powder solution and washing again with clear water after washing with bleaching powder to entire satisfaction of Eng-in-Charge complete all as directed by Eng-in-Charge. Note : Contractor shall provide all necessary arrangements such as Lighting , Non clog Pumps,ladder etc and will make good to disturbed surface with out any extra cost to the department on this account.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and as directed.

All as per serial item No. 20 above but not exceeding 10 cm in width and girth.

Material and Labour for preparation of old painted outer surface of existing sluice valves and non return valves of size 350 mm to 250 mm and applied one coat of synthetic enemal paint complete all as directed.

All as per serial item No. 22 above but for size of valves 150 mm to 100 mm.

All as per serial item No. 22 above but for size of valves 100 mm to 80 mm.

M&L for MS work as in plat form / Frames, Clamps / base frames made of angle, Channel, flat and MS sheet of any size & thickness including cutting, welding riveting, locking arrangement and two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed by Engineer-in-Charge. Note :- (i). Rate of two coats of synthetic enamel paint over a coat of red oxide primer is included in this item and nothing extra shall be paid on this account. (ii). For payment purpose only actual weight of Mild Seel material shall be considered and weight of paint and preimer shall not be considered.

S&F in repair primary filter of CI/PVC with glass wool filter and moisture glass tube with PVC moisture nut complete all as specified and directed. Make : AQUA SERVICES / Peejee/ H- Guru.

S&F in repair PVC gas bend of standard size to connect primary filter and secondary filter complete all as directed by Engineer-in-charge. Make –AQUA SERVICES

S&F in repair PVC non- return valve (NRV) with bend to connect secondary filter and mixing chamber complete all as directed by Engineer-in-charge. Make –AQUA SERVICES

S&F in repair secondary filter of PVC with glass wool, non return valve, moisture glass tube and moisture nut complete all as directed by Engineer-in-charge. Make –AQUA SERVICES

S&F in repair mixing chamber of PVC with glass tube of size 75 mm outer dia x 375 mm in length, glass Orifice tube, PVC water tube, two nos of rubber O ring, rubber bush complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair PVC water bend to connect mixing chamber and solutionizer complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair PVC ‘T’ with Diaphragm valve 15 mm size for drainage water in mixing chamber complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair PVC solutionizer with nuts & outlet connection to delivery water main or in storage UG sump complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair brass nut and nipple for copper pipe connection complete all as directed. Make - AQUA SERVICES

S&F in repair diaphragm type pressure gauge with Teflon packing complete all as directed by Engineer-in-Charge. Make : AQUA SERVICES / Peejee/ H- Guru.

S&F in repair chlorine control valve brass ( niddle valve) complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair chlorine copper pipe 1.20 m long with brass nut and nipple on both end to connect chlorine cylinder and chlorinator complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair Lead washers of various types complete all as directed by Engineer-in-charge. Make - AQUA SERVICES

S&F in repair testing chloroscope kit 0.1 PPM to 5 PPM complete all as directed. Make - AQUA SERVICES Note for Srl Item No. 26 to 39 : Items catered against serial No. 26 to 39 above are for 2.00 Kg capacity chloronum plant spares ( Gravity feed type) .The make of these items shall be same as existing one at site and shall be of ISI Marked duly approved by the Engineer-in-Charge. Before quoting the bid contractor should visit the site to check the capacity and make at site for these items.

S&F in repair slip ring 4 pole 415 volts suitable for 3 HP electric motor with eight Nos carbon brushes mounted on GI pipe with frame including necessary fittings complete all as required at site and as directed.

Opening the top of unserviceable flat sheet valve 600 mm to 450 mm dia and taking out complete assembly from open inlet channel of filtratioin plant and repairing the same including and replace the same with new spindle with check nut, gate valve, ring , gland etc including replacement of worn out nuts, bolts gasket etc with new nuts, bolts gasket etc and refixing the same in original poistion after repairs and testing complete all as directed by the Engineer-in-Charge.

All as per serial item No. 41 above but for flat sheet valve 300 mm dia .

S&F in repair 300 mm dia sluice valve , ISI marked PN 1.0 confirming to IS-14846-2000, both end flanged ,drilled , steel spindle and iron wheel handle , CI gate with MS ring including jointing material such as nuts, bolts, washers and rubber sheet etc complete all as directed by Engr-in-Charge. Make KIRLOSKAR / LEADER / L&T /UPADHYA / ZOLOTO/ BIR

All as per serial item No. 43 above but for 250 mm dia sluice valve. Make KIRLOSKAR / LEADER / L&T /UPADHYA / ZOLOTO/ BIR

All as per serial item No. 43 above but for 200 mm dia sluice valve. Make KIRLOSKAR / LEADER / L&T /UPADHYA / ZOLOTO/ BIR

All as per serial item No. 43 above but for 150 mm dia sluice valve. Make KIRLOSKAR / LEADER / L&T /UPADHYA / ZOLOTO/ BIR

All as per serial item No. 43 above but for 100 mm dia sluice valve. Make KIRLOSKAR / LEADER / L&T /UPADHYA / ZOLOTO/ BIR

All as per serial item No. 43 above but for 80 mm dia sluice valve. Make KIRLOSKAR / LEADER / L&T /UPADHYA / ZOLOTO/ BIR

S&F in repair 200 mm dia foot valve , ISI marked confirming to IS-4038, flanged and drilled with MS ring and flap plate including jointing material such as nuts, bolts, washers and rubber sheet etc complete all directed by Engr-in-Charge. Make KIRLOSKAR / LEADER / L&T / ZOLOTO / VENUS /TATA/ BIR

All as per serial item No. 49 above but for 150 mm dia foot valve. Make KIRLOSKAR / LEADER / L&T / ZOLOTO / VENUS /TATA/ BIR

All as per serial item No. 49 above but for 100 mm dia foot valve. Make KIRLOSKAR / LEADER / L&T / ZOLOTO / VENUS /TATA/ BIR

S&F in repair 200 mm dia non return valve , ISI marked confirming to IS-5312-2004, both end flanged drilled complete with MS ring and rubber flap plate including jointing material such as nuts, bolts, washers and rubber sheet etc complete all as directed by Engr-in-Charge. Make: KIRLOSKAR / LEADER / L&T / ZOLOTO / VENUS / UPADHYA/ BIR

All as per serial item No. 52 above but for 150 mm dia non return valve. Make: KIRLOSKAR / LEADER / L&T / ZOLOTO / VENUS / UPADHYA/ BIR

All as per serial item No. 52 above but for 100 mm dia non return valve. Make: KIRLOSKAR / LEADER / L&T / ZOLOTO / VENUS / UPADHYA/ BIR

S&F MS spindle of sluice valve 500 mm dia including nuts, bolts, washers and rubber sheet after taking out the unserviceable spindle by opening the top of sluice valve complete all as specified and directed.

All as per serial item No. 55 above but for sluice valve 350 mm dia.

All as per serial item No. 55 above but for sluice valve 300 mm dia.

All as per serial item No. 55 above but for sluice valve 250 mm dia.

All as per serial item No. 55 above but for sluice valve 200 mm dia.

All as per serial item No. 55 above but for sluice valve 150 mm dia.

All as per serial item No. 55 above but for sluice valve 100 mm dia.

All as per serial item No. 55 above but for sluice valve 80 mm dia.

Cutting /Cleaning away all grass,bushes,under growth small tree roots,hedges,vegetation, branches of trees etc at installation of water supply up to entire satisfaction of Engineer -in-charge and disposing the same at a distance upto 50 mtr away from the prepherial area under clearence complete all as directed by Engineer-in -charge.

M&L for collection of water sample from different locations as directed by the Engineer-in-Charge in clean/sanitized bottle of capacity 01 Ltr in front of MES rep, carrying out the Bioligical and chemical analysis test from the govt approved laboratory and submiting the test result to Engineer-in-Charge for each sample complete all as directed.

S&F in repair bimetal over load relay single phase protection directly mounted 28 to 42 Amps, range ML2/ML3 complete all as directed by Engineer-in-charge. Make : Siemens /Crompton Greaves/Larson & tubro

S&F in repair bimetal over load relay single phase protection directly mounted 66 to110 Amps, range MN5 complete all as directed by Engineer-in-charge. Make : Siemens /Crompton Greaves/Larson & tubro

S&F in repair bimetal over load relay single phase protection directly mounted 45 to 75 Amps, range MN5 complete all as directed by Engineer-in-charge. Make : Siemens /Crompton Greaves/Larson & tubro

S&F in repair spare coil for Power contactor 415 volt, 50 cycles, 3 phase, type ML-4/ML6 complete all as directed. Make L&T or equivalent make Siemens / ABB/BCH/Crompton Greaves

S&F in repair spare coil for Power contactor 415 volt, 50 cycles, 3 phase, type ML-2/ML-3 complete all as directed. Make L&T or equivalent make Siemens / ABB/BCH/Crompton Greaves

S&F in repair electronic timer (time delay relay) of range 12-120 sec, input voltage 220 to 240 volts AC complete all as directed by Engineer-in-charge. Make: L&T/ABB/CG/Siemens

S&F in repair power contactor 415 volt, 50 HZ, 3 pole, type ML-6 complete all as directed by Engineer-in-charge. Make: L&T /Siemens / ABB/BCH/Crompton Greaves

S&F in repair power contactor 415 volt, 50 cycles, 3 pole, type ML-4 complete all as specified directed by Engineer-in-charge. Make: L&T /Siemens / ABB/BCH/Crompton Greavess

S&F in repair power contactor 415 volt, 50 HZ, 3 pole, type ML-3 complete all as directed by Engineer-in-charge. Make: L&T /Siemens / ABB/BCH/Crompton Greaves

S&F in repair MCCB, 400 Amp, 4-pole,415 Volts, TPN, 50 cycle, breaking capacity 50KA thermal setting 80-100%, Ics-100% Icu confirming to IEC-947, IS-13947 , including thimbles, nuts, bolts, washers etc complete all as directed by Engineer-in-charge. Make : LARSEN & TUBRO/ SIEMENS/LEGRAND/SCHNEIDER/HAVELLS INDIA LTD/C & S ELECTRIC LIMITED (C & S)/ABB.

S&F in repair fully automatic star delta starter 415 volts 3 phase with single phase protection feature with relay range 45 to 75 Amp and contractors suitable for 60 HP electric motor including connection complete all as directed. Make - L&T/ Siemiens /BCH.

S&F in repair wall mounted LED Batten T-8 Retro LED 18/20 watt, appx 4 feet long, pre wired including LED tube light, not less than 5700K, minimum 100 lumen per watt, integrated electronic driver complete fitting and all other accessories fitting arrangements including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector complete all as directed by Engineer-in-Charge. Make - Bajaj ,Cat part No BLRB 18W and BLRB-DB 118 of Bajaj / Crompton, Cat part No.LT8-20-865-(2) and DMLN1LT8-16.

De-stiling and cleaning the open sludge channel from sludge pump house of depth not exc. 1 mtr and removing slit 50 mtr away from outer edge of open sludge channel manually complete all as directed by Engineer in charge.

S&F in repair flexible tyre coupling size TC -015 including making alignment of pump and motor complete all as directed. Make - Unitech

All as per serial item No. 78 above but for coupling size TC -016.

All as per serial item No. 78 above but for coupling size TC -017.

All as per serial item No. 78 above but for coupling size TC -018.

All as per serial item No. 78 above but for coupling size TC -019.

Taking out CI foot valve/Non return valve size 200 mm to 250 mm from jack well approximate 3 mtr deep and refixing the same in original positions after fixing leather buffalow complete all as required at site and as directed.

All as per serial item No. 83 above but for CI foot valve/Non return valve size 100 mm to 150 mm.

All as per serial item No. 83 above but for CI foot valve/Non return valve up to 80 mm. Note for serial item No. 82,83 and 84: Leather buffalow /nut bolts and rubber sheet will be measured and paid seperately under appropriate item of BOQ as supply only.

Supply only leather buffalow superior quality as per sample complete all as directed.

Supply only nut bolts with washers complete off sizes fully threaded/half threaded as required at site complete all as directed.

Supply only oil imeressed graphite gland packing off sizes of superior quality complete all as directed. Make - Champion

M/S KIRT ENTERPRISES

JASPAL SINGH CONTRACTOR

Bidder Name

M/s Kataria Construction Company