SPECIAL REPAIR RENOVATION WORK OF 21 NOS STAFF QUARTERS AT KV NO 1 OLD CANTT PATIALA UNDER GE NORTH PATIALA

Amount

Schedule 'A'Section-I (Building Works)

Total amount of Sch 'A' Sec I (Building Works)

Schedule 'A'Section-II (INTERNAL ELECTRIFICATION WORKS)

Total amount of Sch 'A' Sec II (Internal Electrification Works)

Schedule 'A'Section-III (Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.

Preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion complete all as specified and directed.

S&F factory made flush shutters 35mm thick 7 ply construction, BWP confirming to IS 2202, solid core construction, with block board core and plywood face panels, commercial type on both sides including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm with stainless steel screws - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (wire dia. 0.36mm) and the supply and fixing following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf

S&F powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 101.60 x 44.45 x 1.75 mm for chowkats or frame & shutters made of size 44.45 x 44.45 x 1.29mm for side rails and middle rail, 114.3 X 44.45 X 1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below & above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and including required nos of pivots / hinges and brass mortice lock (four levers) and two nos of key complete all as specified and directed including supply and fixing the following items: (a) Powder Coated Aluminium butt hinges 100mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Providing and fixing aluminium sliding windows with 50 micron powder coating, three track sliding windows with two glazed shutters, 5mm thick tinted glass ordinary quality and one shutter of stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm including good quality of bearing handle, locks, including EPDM gasket to render the glazing, air and water tight etc complete all as specified and as directed . Section of Jindal Company : Three track bottom - 20957, Three track top / vertical - 20958, handle - 20606, Interlocking - 20605, Top and Bottom - 20604.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

Providing and fixing factory made aluminium ventilators with 80 micron powder coating of frame of 127X38.10X1.74 mm and fixed shutters made of 45X45X1.63mm including 5mm thick glass in lower half portion of shutters and stainless steel wire gauge 32 Gauge in upper half portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

S&F health faucet (ABS Body) with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F 6mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish with wooden beading french polished, etc.complete fixed in position all as specified and directed.

Basin mixer for wash hand basin, fancy type, chromium plated, 15mm bore, fixed as in repair complete all as specified and directed

M&L for wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, non telephonic shower arrangement, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and directed.

Repair to RCC sunshades, Chajjas, Balconies, Columns, bands, beams and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

Applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 200 mm micron thick polythene film over 85/25 grade bitumen layer @ 0.5 kg /Sqm all as specified

S&F single Y-shaped CI junction pieces, ordinary or inverted (spigot or socket type) for 100mm bore pipes complete all as specified.

Providing and laying 3mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.0 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm th 5 layered APP membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength inlongitueinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

M&L for 20-22mm thick precast plain cement concrete tiles type B-1, 1:2:4 (12.5mm graded aggregate) as in floorings, roofing set in cement mortar 1:4 over and including 15mm th screed bed in CM 1:4 complete all as specified.

Supply and apply of rust remover cum passivator by brush in two coat @ 0.3 kg/m2/coat of Density: 1.01 Kg/l at 300C complete all as per manufacturer's instructions and all as specified. Note : The application of rust removal shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

Supply and apply Cementitious Coating for Corrosion Protection having a cement based polymer modified rebar corrosion protection system by appling the first coat approx. 1mm thick layer of product carbonation resistance 2 mm of SikaTop Armatec®-108 or equivalent as specified corresponds to 20 mm of normal mortar; bond strength > 1N/mm2 according to ASTM C 882-78 applying @ 4 kg/m2 for two coats onto the prepared reinforcing steel with a medium- stiff brush. It is unavoidable that Sspecified product will also be applied onto the surrounding concrete. The second coat is applied in the same way after a waiting time of 2-3 hours (at +20°C) complete all as per manufacturer's instructions and all as specified. Note : The application of Cementitious Coating for Corrosion Protection shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface by chipping and throughly cleaning of surface complete whereever required and as per directions of Engineer-in-charge. Consumption: 0.5 kg/m2. complete all as per manufacturer's instructions and all as specified. Product requirements: Complies with ASTM C 881 Type II Grade 2 Class B+C. Note : The application of Epoxy Bonding Primer shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

Supply and apply a pre-batched one component polymer modified cementitious patch repair mortar in 25 mm thickness. Yield: approx. 0.84 ltr/kg. System requirements: compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109; flexural strength >= 3N/ mm2 (7 days) according to ASTM C 293-79. Consumption of 2.1 Kg/Sqm/mm Note : The application of Polymer repair Mortar shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

S&F 18 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of both side plain white color fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

S&F 18 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single rigid laminated of approved colour and other side plain white colour fixed with screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s specifications complete all as specified and directed.

S&F 12 mm thick LEAD FREE PVC Celuka ply fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed.

S&F 6 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC ply fixed withss screwed and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer side complete as per manufacturer’s instructions complete all as specified and directed.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position all as specified.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs,

S&F tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished complete fixed in position all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified.

S&F Piano/continuous hinge of size 19 mm stainless steel complete all as specified.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified.

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required suze complete fixed in position all as specified.

S&F Stainless Steel 304 grade Basket Cutlery of size 370X485mm premium quality complete fixed in position all as specified.

M & L rubber moulded coloured chequered tiles 30 cmx30 cm x22 mm thick with grey cement and pigment , set jointed and pointed in neat cement slurry as in floor

Supply only chicken wire mesh 22 gauge of size not less than 20X20mm all as specified & as directed by Engineer-in-Charge.

PCC 1:2:4 type B 0) using 12.5 mm graded stone aggregate 25 mm thick mixing with WPC as in bedding in sunken portions etc complete all as specified and directed.

M&L for point wiring with 1.50 sqmm(22/3mm) pvc insulated and unsheathed FR single core stranded copper conductor for one light / fan in new PVC conduit medium grade 19/20 mm dia to be terminated in pressed steel terminal boxes with modular cover plate including 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FR single core stranded copper earth continuity conductor controlled by one switch and / or one regulator complete including repair the surface in CM 1:3 and finishing the surface as per existing treatment all as specified and directed (Switches and regulators shall be measured and paid for seperately) (Wiring shall be done as per colour code in IS for phase, neutral and earth) NOTE : Modular metal flush boxes and modular cover plates shall be measured and paid seperately.

All as per Sl item No 42 herein before but one socket out let 5 pins 5 Amp on the same board but with other switches complete all as specified and directed by Engineer in Charge.

All as per Sl item No 42 herein before but one socket out let 5 pins 5 Amp on independent board omplete all as specified and directed by Engineer in Charge.

Metal flush boxes mounting 8 module, made of MS chromium plated complete all as specified and directed by Engineer in Charge.

S & F Lamp holder incl flexible wire 0.5 Sqmm copper cable all as specified and directed by Engineer in Charge.

Supply &Fix tube light fitting LED type retrofit T-8,20 watt,4 ft long incl LED tube rod and incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed.

Supply & Fix tube light fitting LED type integrated 9/10 watt, 2 ft long incl LED tube rod and incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed.

Supply and fix bulk head fitting LED type incl 1 x 9/10 watt LED lamp,with flexible wire 0.5 sqmm copper cable all as specified & directed.Note: Bulk head fitting will be issue from store yard of MES.

Taking down ceiling fan and refixing after neccery cleaning complete all as specified and directed.

S& F Sheet metal enclosure suitable for fixing DB and Electric meter, factory made of size 50 x 50 x 18 cm made out of 2mm thick MS sheet with double door, sutiable locking arrangements, powder coated, cutting chasing in wall and fixing and making good as per existing surface complete all as specified.

S&F earth metal plug with MCB SPN 32 amp complete all as specified and directed by Engineer in Charge.

S&F MCCB TPN,4 Pole,415 volts,100 amp, 16 KA rupturing capacity for fixing in DBs of including proper thimble connections complete all as specefied and directed.

S&F MCCB DB TPN 4ways double door 415 volts with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting type, drilling holes for incoming and out going cables complete with IP-42 all as specified and directed by Engineer in Charge.

Supply and fix exhaust fan 300 mm sweep complete all as specified and directed.

Supply and fix pvc exhaust fan 230 mm sweep complete all as specified and directed.

Supply and fix geyser 25 litre capacity complete all as specified and directed.

Supply and fix service wire 16 sqmm 2 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed.

M & L for precast concrete cable covers class LV, Type 1, flat, size 300mmx l80mm x 40mm laid dry in trenches for cable protection all as specified and directed by Engineer in Charge.

Sand bedding for coushing of cables complete all as specefied and directed by Engineer in Charge. Note:- Punned thickness of 18 Cms will be measured and paid.

S&F GI pipe light grade 40 mm passing through cables, walls , across the roads with proper clamps, nut & bolts including taking down complete all as specefied and directed.

Supply and fix bell ding dong electronic complete all as specified and directed by Engineer in Charge.

Arneja Builders

KG BUILDERS

HG construction

DELTA CONSTRUCTION CO

Swami Enterprises

M/S Mukesh Kumar Gupta