8971 ADDN ALTN AND RENOVATION TO TEMP ACCN OF GUEST ROOM AT HUT BAY

Amount

SCHEDULE 'A' : PART -I (B/R Portion) :- Demolition of Concrete of any description and in any position not otherwise provided for including sewage pipe etc complete all a specified and directed and directed by Engineer in Charge.

Dismantling of unframed wooden work such as fillets, rails, posts,rafters, purlins, etc. under 40 sq. cm in section in any position complete all as specified and directed by Engineer in Charge.

Taking down cement plaster or screed bed with tile on block masonary walls, etc. including raking out joints, hacking for key, scrubbing downwith water, etc. complete all as specified and directed by Engineer in Charge.

Material and labour for 25mm plain Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in levelling course complete all as specified and directed by Engineer in Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as directed and directed by Engineer in Charge.

Demolition textile coverings incl frames (if any ) and cover fillets (measured flat and not girthed and directed by Engineer in Charge.

Breaking up drain pipes (any size or pattern), including all fittings, etc., in any position complete all as specified

Material and labour Precast cement concrete type B0 (1:2:4) using 12.5 mm graded aggregate Set in CM(1:4) louvres and jallies, 40mm thick (measured solid), including all mouldings but excluding frame and directed by Engineer in Charge.

Material and labour reinforced Cement Concrete type B1 (1:2:4) using 20 mm graded aggregate in Columns and the like complete all as specified and directed by Engineer in Charge.

Material and labour reinforced Cement Concrete type B1 (1:2:4) using 20 mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete and the like complete all as specified and directed by Engineer in Charge.

Material and labour reinforced Cement Concrete type B1 (1:2:4) using 20 mm graded stone aggregate as in Chajjas and the like complete all as specified and directed

Material and labour for reinforced Cement Concrete type B1 (1:2:4) using 20 mm graded stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span as directed complete all as specified and directed.

Material and labour Cement Concrete type B1 (1:2:4) using 20 mm graded aggregate in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating as directed complete all as specified and directed.

Material and labour for precast cement concrete hollow block masonery 10cm thick type C1 1:3:6 using 16mm graded aggregate set in cement mortar 1:4 complete all as specified as directed.

Taking down Aluminium Chowkats or frames exc 1.5 sq.m but n exc 4 sq m each with shutters (without taking off shutters from the frames) and refixing in other opening complete all as specifed and directed.

Supply and fix in repairs aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specified.

Supply and fix aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified.

Supply and fix Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

Supply and fix extruded aluminium alloy handles size 150 mm fabricated type, anodised complete all as specified and directed by Engineer in Charge.

Supply and fix butt hinges stainless steel 100 mm long, medium weight, and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fix anodised aluminium alloy medium grade curtain rod 20 mm dia including decorative type brackets etc complete all as specified and directed by Engineer in Charge.

Supply and fixing in repairs aluminium alloy wire cloth, 0.45mm nominal dia of wire & average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer in Charge.

Supply and fix of Rolled mild steel Joist, channel, angle, or tee sections / tubes confirming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer in Charge.

Supply and fix Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook & pintel hinges; large hasps & staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way & three way straps, plate washers & similar small articles conforming to Fe290-0 Gde E-165 and directed by Engineer in Charge.

Material and labour for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Quality confirming to FE 500D complete all as specified and directed by Engineer in Charge.

Ditto above but 6mm to 8mm dia complete all as specified.

Ditto above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

Use and waste formwork to chullah hoods, chajjas, troughs & similar items including edges complete all as specified and directed by Engineer in Charge.

Use and waste Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors, roofs & sides of RCC/ PCC bands in walls, horizontal or sloping, and similar work all exc. 20cm wide., rough finished surfaces of concrete flat surfaces of concrete complete all as specified and directed by Engineer in Charge

Supply and fix powder coated of any colour (thickness of powder coating not less than 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates (thickness of section shall be not less than 2 mm) including joining cleat for fixing etc. complete all as specified and directed by Engineer in Charge.

Supply and fix powder coated of any colour (thickness of powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Engineer in Charge.

Supply & Fixing of anodised aluminium snap grid frame work 600mm x 600mm consist of 25 x 25 x 1.5 mm angle, main tee 25 x 38 x 2mm and cross tee 38 x 25 x 1.5mm for false ciling including hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof truss support by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia x 40 mm long complete all as specified.

Supply & fixing of 4 mm non asbetos fibre cement builing boards 600 x 600 mm fixed in ciling of Aluminium framework with screws including two coat of OBD and over a coat of primer complete all as specified.

Material and labour for Glazed ceramic pattern tiles, coloured, 450x300x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, incl border tiles, design/pattern as directed by Engr-In-Charge, backing plaster 10 mm thick in CM (1:4), finishied rough, complete all as specified and directed by Engineer in Charge.

Material and labour for Non - skid Coloured ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the tiles over 15 mm thick Screed bed or bedding layer of cement mortar in 1:6 complete all as specified and directed by Engineer in Charge.

All as per item above, but as in skirting over 10 mm thick cement plaster 1 : 4 all as specified.

10 mmm thick rendering in CM 1 : 4 on fair faces of block work or concrete surfaces and to be finished even and fair complete all as specified.

Material and labour for 5mm thick rendering in CM 1:4 mixed with approved water proofing compound as per manufactueres instructions over 10mm thick rendering in CM 1:6 on fair faces of block work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and directed by Engineer in Charge. Note : water proofing compound will be measured and paid seperately

Supply only integral water proofing compound

Material and labour for Preparation of newly plastered wall surface, apply 3mm thick layer of white putty over a coat of primer, applying two coats of Plastic Emulsion complete all as specified and directed by Engineer in Charge.

Material and labour for Vitrified Ceramic tiles dark shaded, 9-10 mm thick (square/ rectangular), polished, area of each tile not exceeding 0.36 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match the tile colour over 15 mm thick Screed bed or bedding layer of cement mortar in 1:6 complete all as specified and directed by Engineer in Charge.

Supply and fix 4mm thick, figured glass (coloured pin headed type and glazing with aluminium clips in square n exc 0.5 sq. m in each panel complete all as specified and directed by Engineer in Charge.

Material and labour for Preparing the old wooden surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of sythetic enamel paint complete all as specified and directed by Engineer in Charge.

Material and labour for for preparing new plastered surfaces and applying two coat of exterior emulsoin paint (anti fungal weather coat) over one coat of primer complete all as spd and directed by Engr in Charge.

Material and labou for Preparing the new steel surfaces of any description, over 10cm in width or girth,not otherwise described and painting two coat of sythetic enamel paint over a coat of red oxide or zinc chrome primer complete all as specified and directed by Engineer in Charge.

Material and labour for Preparing the old steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of sythetic enamel paint complete all as specified and directed by Engineer in Charge.

Taking up or down steel tubing & connections, including cleaning for re-fixing or removal to store of 15mm bore complete all as specified and directed by Engineer in Charge.

Supply and fix 15 mm bore galvanized iron tubes, medium grade, with all fitting and fixed complete to walls and ceilings or laid in floors, concealed in walls, complete all as specified and directed by Engineer in Charge.

Supply and fix 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc 32 mm bore and fixed complete all as specified and directed by Engineer in Charge.

S & F bib taps, cast copper alloy chromium plated Fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe of 15 mm dia and fixed complete all as specified and directed by Engineer in Charge.

Supply and fix Mild steel body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters not exc 700 mm in width and of weight nt exc 35 kg and fixed complete all as specified and directed by Engineer in Charge.

Supply and fix Stop valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer in Charge.

Supply and fix fibre reinforced PVC connecting pipe 60cm long with brass check nut and washer on both side complete all as specified and directed by Engineer in Charge.

Supply & Fixing in repair of Vitreous China wash basin, Oval shape 1st quality with CI Brackets, angle back,, size 600 x 480 mm white colour excluding taps wate chain & plug incl pinning in ends and connections, complete all as specified and directed by Engineer in Charge.

Supply & Fixing in repair of vitreous China pedestral pan in built cistern and trap white, and 'P' or 'S" trap connection to drain (or outgoing pipe ) and to flush pipe, anti syphonage pipe etc including plastic seat cover in white colour with necessary MS chromium plated or aluminium hinge and complete all as specified and directed by Engineer in Charge.

Supply and fix in repair of aluminium hat and coat hooks, solid body, 175 mm to 250 mm overall length all as specified and directed by Engineer in Charge.

Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in soft/loose soil

Material and labour for excavation of soft/loose soil in post hole ( or similar holes ) each n. exc 0.5 cu.m getting out returning filling in and ramming earth or broken rubble mixed with earth around, in layer nt exc 25 cm watering and removing surplus soil to a distance nt exc 50 m and making good surface all as specified and directed by Engr -in-Charge.

Returning filling in soil including spreading, levelling, watering & well ramming in layers n. exe 25 cm.

Removing excavated soil n.exc 50m and depositing where directed at a level n. exe 1.50m above the starting point in Soil.

Use and waste formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. rough finished surfaces of concrete flat

Material and labour Cement concrete in foundations, filling and mass concrete. Type D2 1:4:8 (using 40 mm graded aggregate) complete all as specified and directed.

Material and labour Pre cast cement concrete block masonry (Type C1 using 20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar in 1:6 complete all as specified.

Material and labour cement concrete Type C2, 1:3:6, 40mm graded aggregate as in mass filling, foundation, fixing of MS Posts, etc..

Supply & fixing rolled steel sections as in framing for cladding of tubular or other section with rails, braces, etc including fixing of expanded metal (hard drawn mild steel wire) complete drilled for fixing or welding etc, like fixed with angle cleatsand connecting plates etc complete all as specified.

Supply & fixing rolled sections as in framing of angle or other section with gueest plates, rails, braces etc complete drilled for fixing etc to be prepared for hanging or sliding with and including either hooks and hinges for steel gates and fixed with angle cleats and connecting plates etc cmplet eall as specified.

Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering under floor as required complete all as all as specified and directed by Engineer in Charge.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

Supply and fix Pre-painted galvalume aluminium zinc coating GI based coloured corrugated steel sheet, 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws to tubular steel frame work, as specified.

Supply and fix Pre-painted galvalume aluminium zinc coating GI based coloured Plain steel sheet, 0.5mm thick of any colour having tensile strength of 550 Mpa as in Gate covering/Ridge to wall,fixed with self tapping screws to tubular steel frame work, as specified.

Material and labour for Preparation of newly plastered wall surface and applying three coats of white wash all as specified and directed by Engineer in Charge.

Forming jambs etc to opening with blocks including cutting, toothing and properly bonding into old work including facing and pointing to match existing work in CM 1:4, complete all as specified and directed

Making good under cills or over arches, lintels and bressummers, including all pinning when necessary new work built in CM(1:6) complete all as specified and directed

Supply and Fixing in repairs of 20 mm thick black granite (colour approved by Engr in charge) as in cills/ jambs / counter / platforms, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types laid over 20 mm thick screed bed in CM (1:6) complete, all as directed by Engg-In-Charge.

Supply and Fixing in repairs of 12 mm thick black granite (colour approved by Engr in charge) as fixed in walls / jambs machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types laid over 10 mm thick screed bed in CM (1:4) complete, all as directed by Engg-In-Charge.

Material and labour for 5mm thick rendering in CM 1:3 mixed with approved water proofing compound as per manufactueres instructions on fair faces of block work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and directed by Engineer in Charge. Note : water proofing compound will be measured and paid seperately

Material and labour for 40mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds & similar work n exc 15cm in width or girth; including cutting to edges, all mitres & stopped ends, etc.

Use and waste formwork, rough finished surfaces of concrete Square, rectangular or polygonal to sides of pillars, posts, struts, columns, etc., complete all as specified and directed by Engineer in Charge.

Supply & Fixing of chromium plated shower rose 300 mm dia with or without swivel joints, any size, incl fixing, screwed down, screwed for iron pipe of 15 mm dia and fixed complete all as specified and directed by Engineer in Charge.

Solid PVC Door Frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC Sheet reinforced with MS Square tube supplying & fixinf in opening as per specification & drawing.

Factory made solid PVC Moulded Door Shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 3 mm thick Moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing

Taking out old serviceable glass of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc. including making good breakages in taking out & stacking for reuse and Securing sheet glass of any description in existing wooden frames glazed, ordinary quality & glazing with oil putty in square in each pane to match existing work fixed complete all as specified and directed by Engineer in Charge.

Taking down carefully copper/aluminum existing point wiring (light/fan/socket or power points) complete incl wooden battens/casing capping or conduit etc (without disturbing existing fittings point wiring etc) and all connected fittings such as switch, socket, ceiling rose, lamp holder, brackets ceiling fittings, bulk head fittings and fan regulator etc and making good to disturbed surfaces of wall floor etc all as directed.

Taking down unserviceable main switch / DB's incl MCB's of any size and type, making good to the disturbed surfaces by matching with the adjoining surfaces complete all as specified and directed by Engineer in Charge.

Taking down unserviceable sub main wiring of any type, any size, making good to the disturbed surfaces by matching with the adjoining surfaces complete all as specified and directed by Engineer in Charge.

Taking down and refixing the existing exhaust / ceiling fan / wall mounted fan of any type and size, complete all as specified and directed by Engineer in Charge.

Taking down existing light fittings any type, any size, removal from site making good to the disturbed surfaces by matching with the adjoining surfaces complete all as specified and directed by Engineer in Charge.

Material and labour for Point wiring with 1.50 Sqmm (nominal area) PVC insulated unsheathed copper stranded conductor (FRLS) cable in and including PVC casing and capping of suitable size including 1.5 Sqmm PVC insulated copper earth continuity conductor connected to common earth dolly controlled by one switch on PVC board all as specified and directed forOne light point controlled by one, one way switch

All as per Sl item No. 89 here-in-before but of One fan/exhaust/wall mounted fan point

All as per Sl item No. 89 Socket 5 Amps on same board

All as per Sl item No.89 Socket 5 Amps on independent board

All as per Sl item No.89 One calling bell point controlled by one bell push switch

All as per Sl item No.89 but using 4 Sqmm copper cable for Power Point

Supply and fix DB, SPN 12 way, 240 V, industrial type, double door,factory made with 200A rated bus bar complete with neutral and earth link suitable for fixing of MCBs complete all as specified

Supply and fix DB, SPN 4 way, 240 V, industrial type, double door,factory made with 200A rated bus bar complete with neutral and earth link suitable for fixing of MCBs complete all as specified

Supply and fix MCB SPN, 240 V, 63 Amps complete all as specified

Supply and fix SPN, 240 V, 20 Amps complete all as specified

Supply and fix MCB SP 5 to 32 A complete all as specified

Supply and fix Modular switch piano (ISI marked) flush type 5A, 230 V, AC supply, single pole, one way complete all specified

Supply and fix Modular Socket (ISI marked) 6 Amps 2/3 Pin comnined 2 module complete all as specified

Supply and fix Modular switch socket outlet multi purpose (ISI marked), 2 in 1, suitable for one 3 pin , 5 and 15Amp , 230 V, flush type, complete all as specified.

Supply and fix Modular switch (ISI marked) flush type 16A, 230 V, AC supply, single pole, one way complete all specified

Supply and fix modular white cover plate with frame, one way 16 Amps - 1 module all as specified

All as per Sl item No.99 here-in-before but 2 module

All as per Sl item No.99 here-in-before but 4 module

All as per Sl item No. 99 here-in-before but 6 module

Supply and fix Metal flush box 1 or 2 modules for modular switches all as specified

All as per Sl item No. 103 but for 4 modules

All as per Sl item No. 103 but for 6 modules

Supply and fix bell push, flush type, 5A 230 V, (ISI marked) AC supply complete all specified

Supply and fix in repairs, Lamp holder PVC / Polycarbonate type with back plate suitable for battern fittings.

Material and labour for Sheet metal encosures with socket plug top and earth complete with 20 Amps one single pole MCB all as specified.

Supply and fixing recesses mounted LED downlighters light fitting with the option for dimming solutions,energy efficient, corrosion resistant, impact proof ceiling mounted LED Lighting, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver incl flexible copper cable 1.5 sqmm, 2-3 mtr long 3 core from ceiling rose to connector of fitting complete all as specified. Make : CP No. DN395B LED 20S-6500PSD WH or equivalent in Philips/Crompton Greaves/Havells.

Material and labour for sub main wiring with 1100 volts grade , 2 single run, 4 sqmm pvc insulated unsheathed multi strandaed copper conductor cable drawn through and including PVC casing & caping of suitable size with all fittings on surface of wall/roof alongwith 4 Sqmm multi stranded copper conductor cable green in colour as continuous earth wire complete all as specified and directed

Material and labour for sub main wiring with 1100 volts grade , 2 single run, 6 sqmm pvc insulated unsheathed multi strandaed copper conductor cable drawn through and including PVC casing & caping of suitable size with all fittings on surface of wall/roof alongwith 6 Sqmm multi stranded copper conductor cable green in colour as continuous earth wire complete all as specified and directed

Material and labour for earthing complete with Galvanised steel earth plate eletrode 60 cm x 60 cm x 6 mm thick burried directly in grounds (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level including provision of Galvanised GI wire of size 4mm dia connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 15 mm dia GI pipe medium grade for protection of GI wire and 20 mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chember, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I

M/s K Rudra Murthy