REPAIR/MAINT OF FENCING, BOUNDARY WALL IN ZONE -2A, 9C AT TALBEHAT MIL STN

Amount

Taking down cement or cement lime plaster on brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick plaster in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth w/o using extra cement complete all as specified and directed.

M & L preparation new plastered surfaces of walls and providing two coat of cement base paint complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. Note: All debris obtained from demolition shall be removed 1.5km to 2km complete all as specified and as directed.

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in foundations, fillings, mass concreting complete all as specified and directed.

M&L PCC (1:3:6) type C-2 using 20mm graded stone aggregate 75mm thick as in plinth protection and similar nature works finished surface even and smooth without using extra cement laid in alternate bays n.exc 2m in length all as specified and directed.

M&L for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in PCC band, PCC beam, benching of drain, coping,slightly rounded or chamfered angles and throating, and similar work as directed etc complete all as specified.

Demolition of brick work or stone / boulder masonary,built in cement mortar incl all quoins , pillars etc complete all as specified and directed.

M&L for brick work with old size sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Ditto above item except brick complete all as specified and directed.

Providing precast cement concrete type B1 1:2:4 20 mm graded aggregate as in cover slabs for septic tank/ manholes/drains set in cement Mortar 1:4 complete all as specified and as directed.

S&F of Solid FRP man hole cover of size 60cmx60cm with handle weight not less than 12kg fitted to manhole any type and surface making good in CM 1:3 complete all as specified and as directed. Make : Fluton polymers/Sigma or as equivalent brand all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed concrete,brick,masonry work complete all as specified and directed.

Dismanting of Barbed wire fencing or any type and size

Excavating in post holes in soft/loose soil each n. exc. 0.5 cum getting out , returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25 cm, watering & removing surplus soil to a distance N.exc 50 m and making good surface .

M&L for PCC 1:3:6 , type C-2, using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete & similar work complete all as specified and directed.

M&L PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in band,beam,benching of drain,man hole,coping,slightly rounded or chamfered angles and throating,and similar work including necessary form work all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls,or beam horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed by Engineer-in-Charge.

Supply only chain link MS galvanised medium coated confirming to as per IS-2721-1979 fencing 75mm x 75mm mesh & 3.00 mm dia of wire complete all as specified and directed.

Fixing only chain link fencing incl line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provn of binding wire complete all as specified and directed.

S&F expanded metal welded steel wire fabric, made of GI hard drawn wire mesh of size 25mmX25mm, plain steel wire , fixed to MS frame work complete all as specified and as directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Surface excavation in loose soil n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out

S&F Mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for Chain link fencing confirming to Fe 410-w (Gde E-250) complete.

S&F 5 to 10mm dia of shank Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm but n.cex 10cm long complete all as specified and directed.

S&F Framed/ Unframed work as in doors or gates of angle or other section with gusset plates,rails,braces,also small article for old gates etc complete,all small articles including drilled for fixing of steel sheeting or other covering etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed.

S&F MS sheets1.25mm plain black sheet cut to size,holes punched including rounded headed scarews, clout nails or rivets and fixed to steel framing with plain 40mm lap joints with riveted or welded seams including bending or as in covering to door shutters complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L TMT bars 10 mm dia and over cut to length bend to shape required incl. cranking hooking ends and binding with and incl. MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

S&F Mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for Chain link fencing confirming to Fe 410-w (Gde E-250) complete all as specified and directed.

Demolition (carefully w/o damaging the other part of building) of RCC concrete as in chajjas, fins, parapet etc including cutting of reinforcement to facilitate the provision of new with all necessary scafolding at any height complete all as specified and directed .

M&L for RCC nominal mix 1:2:4 type B-1(using 20 mm graded aggregate) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC nominal mix 1:2:4 type B-1(using 20 mm graded aggregate) for Columns, pillars, piers, posts and struts complete all as specified and directed.

Preparation of new steel surfaces of any description n. exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc crome primer all as specified

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. Note: All debris obtained from demolition shall be removed 1.5km to 2km complete all as specified and as directed.

M & L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) finished fair & even as in floor and similat work complete all as specified and directed

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in pillars,steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M & L for 3mm thick Glass dividing strips and 22 mm width complete all as specified and directed

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)

M/s Indu Enterprises

M/S A.R BUILDERS

M/S ARVIND SINGH THEKEDAR