REPAIR TO FLOORING, WALLING, TOILET MISC REPAIRS IN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

M&L for vitrified tiles 9 to 10mm thick (square/rectangular) in any pattern area of each tiles not exceeding 0.36 sqm, in floors/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 15 mm th screed in cement mortar 1:6 complete all as specified and directed.

M&L for vitrified tiles 9 to 10mm thick (square/rectangular) in any pattern area of each tiles exceeding 0.36 sqm but exc .42 Sqm, in floors/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 15 mm th screed in cement mortar 1:6 complete all as specified and directed.

M&L Glazed printed/ coloured ceramic tiles in vertical surface 300x 450x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement 1 :4 and pointed in white or coloured cement to match the shade complete all as specified and directed.

S&F joint free anti skid printed and coloured ceramic tiles area of each tiles exceeding 0.06sqm but not exceeding 0.11 Sqm and 7mm thick as in floor set & jointed in neat cement slurry & pointed in coloured cement to match over 15mm thick screed in cement mortar 1:6 complete.

M&L 16 to 18 mm th Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, WHB counter and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl cutting for WHB etc over 10mm thick screed bed or bedding layer of cement mortar 1:4 and including moulding and incl taking down old stone complete all as specified and as directed

S&F in repair factory made uPVC white colour fixed glazing made of extruded profile with wall thickness of 2.0mm (+/- 0.2mm). Window profile with hollow section with multi chamber, frame (60mmx58mm) including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware EPDM gasket + -0.2 mm thick galvanized steel frame (28mmx21.5mm) 'T' profile (27mmx17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Note : Glass shall be measured and paid separately however cost of all other connected accessories deemed included in unit rate. Net opening will be measured for payment purpose.

Providing and fixing in repairs factory made UPVC window/door frame for three track window / Door made of UPVC made of extruded profile with wall thickness of 2.3mm (+/- 0.2mm). Window profile with hollow section with multi chamber, frame (60mmx58mm), sash (60mmx78mm). T profile (One vertical length in between two shutters) (60mmx71mm) Glazing bead corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware EPDM gasket + -0.2 mm thick galvanized steel frame (28mmx21.5mm) sash (31mmx27mm) 'T' profile (27mmx17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : Each shutter with zinc alloy touch lock, Zinc alloy roller, handle with mortice lock, rubber gasket etc, complete as per manufacturer's specification . Note : Glass and wire mes shall be measured and paid separately however cost of all other connected accessories deemed included in unit rate. Net opening will be measured for payment purpose.

S&F 5mm thick tempered glass in uPVC or aluminium door and window shutters /frame(for fixed window) complete all as specified and directed

S&F frosted lamination in required design over toughened/float glass incl making logo or design as approved. (Note: for measurement full size of glass will be measured.

M&L in repairs powder coated aluminium wk as in partition wall/door Chowkhats/door/ windows shutters using JINDAL section single groove any suitable section conforming to IS-733 and IS-1285 amd coating grade A-153 confirming to IS-1868 fixed with rawl plug and screw or with fixing clips with expansion hold fasteners including necessary jointing cleats, glazing clips, rubber packing anodised aluminium snap beading packing anodised aluminium snap beading screws, powered coated anodised aluminium fittings etc gap of junction at top, bottom & sides to be filled with silicone fillers/Neoprene felt etc complete all as specified and directed.

M/L in repairs Powder coated aluminium door shutters, aluminium section weighing 1.3 kg/m approx including each shutter having 2 Nos. ‘D’ type aluminium handles of 200 mm long, 2 Nos. aluminium tower bolts of 200 mm long and 1 No. mortice lock of 6 lever with key in duplicate, regulated by double action hydraulic floor door spring, shutter partly glazed with 5.5 mm thick sheet glass and partly panelled with 12 mm thick pre-laminated particle board fixed with glazing clips, rubber beadings and aluminium beading complete all as specified and directed. ( Glass & Prelaminated particle board paid separately)

M/L in repairs Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m approx. including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S&F Stainless steel 304 grade wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed to uPVC or aluminium window /door frame complete all as specified.

S/F in repair vitreous china coloured One piece EWCs with integrated cistern, seat cover and flush fittings and including P or S trap etc. all as spfd and completed ( Cat part 92535 (P-18.5) of Hindware or Equivalent )

Supply and fix in repair counter top oval shape any coloured wash hand basin of size 48cmx48cm depth 13cm Cat part of Jaquar OPS-WHT-15901N or Equivalent in cera, hindware complete all as specified and directed.

Supply and fix in repair for toughened glass of 12 mm thick of any colour as directed by GE as in doors, partitions, windows, bathing cubical with sliding door etc with Kolf SAFEX or OZONE fittings accessories like handle, door machine and all necessary required accessories/fitting for fixing complete, all as specified and directed by Engineer-in-Charge.

S & F in repair glass corner triple layer shelf assembly with CP frame complete all as specified and directed

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets/board fixed in aluminium door or partition, any thickness, including cover fillets & framed work if necessary complete all as specified and directed.

Material and labour for gypsum false ceilings with size 60cm x 60cmx9mm thick false ceiling tiles laminated on face and side with decorative PVC films and a metalize polyester film on back sides back in dew drop texture Ceiling tiles shall be fixed over and incl Powdered coated GI T- grid system of size 600X600 mm as per the manufactures instructions. Note Rates includes for taking down electrical fitting and refixing the same if required complete all as specified and directed.

Material and labour for false ceiling using powder coated GI snap grid system with roll-formed out of hot dip galvanized steel capping (powder coated) main runner and cross tee made of 38x24mm and wall angel 24x24mm members suspended with 1.60mm dia GI wire fixed with fastening on ceiling of roof, carry maximum load up to 8.10 Kg/Sqm including 0.70mm thick pre painted powder coated galvanized steel sheet on external surface and primer on inner surface board as per manufacture’s instructions. Size of board should be 595x595mm x0.70mm thick as approved by GE all as specified and directed

M&L for 10mm thick plaster of Paris ceiling (Gypsum anhydrous) to sunk or raised moulding to flat surface over metal frame work incl reinforced with G.I. wire mesh & Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre & Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long all as specified and directed. Note Rates includes for taking down electrical fitting and refixing the same if required complete all as specified and directed.

Same as above item no but as coup (down or raised portion) of POP 300mm wide and 150mm down false ceiling (for measurement only coup side will measured other portion will measured in above item)

M & L for taking up or down 15mm bore steel tubing complete all as specified and as directed.

M & L for taking up or down 20mm bore steel tubing complete all as specified and as directed.

M & L for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete

All as per item above but 20mm bore complete all as specified and as directed.

S&F In repairs PVC flushing cistern , 10 Ltrs Capacity low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes complete

S & F in repair Bib taps fancy type cast copper alloy chromium plated screwed down screwed for iron pipe, 15mm bore complete.

S & F in repair Pillar cock, CP 15mm bore cast copper alloy with chromium plated fancy type screwed both ends, screwed down high pressure without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe.

S&F in repair Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook complete all as specified and as directed by Engineer-in-Charge.

S&F in repair brass chromium plated shower rose 125 mm size with swivel joints including fixing to pipe complete all as directed

S&F in repair 5mm thick glass sheet shelf 12 mm wide with CP bracket guard and railing 60 cm long complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 5 mm thick glass corner with 12" dia with steel railing and fixed with CP screw & cup washer on wall.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified and as directed

S&F in repair 4 mm thick sheet glass ordinary quality and glazing with shutters in properly of any size in each pane incl hacking out up to 3 storey bldg. complete all as specified and directed by Engr-in-charge.

Supply and fixing in repairs Aluminium die cast Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 36 to 60 kg complete all as specified and directed.

S & F in repair wash hand basins, vitreous china flat back of size 630 mm X 450 mm including cutting for and pinning in ends of brackets or erecting stand including brackets duly painted, 32 mm dia waste fitting of brass, PVC waste pipe of 32 mm dia and of suitable length etc complete all as specified.

S&F in repairs Vitreous china wash down water closet pan(pedestal pattern) including connection to drain (or outgoing pipe) and to flushing pipe antisphonage pipe , etc including seat and cover for pedestal pan, flush pipe, incl all joints complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orissa” pattern of size 580mmx440mm “white” with integral foot rest (excluding flushing cistern and flush pipe) incl provision of cement concrete bedding, CI ‘P’ trap 100mm dia connection to trap and flushing pipe, anti-syphonage complete all as specified and directed.

S&F in repair 30 to 40 mm thick FRP jalli for wall cladding at the edge shall be stuck at the place where two panels are jointed using solvent compound complete all as specified and directed by Engineer - in - Charge.

M&L in repair Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. complete all as specified and directed by Engineer - in - Charge.

M&L complete removal of existing treatment of walls and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth all as specified and directed

M & L complete removal of existing treatment of walls and applying two coats of exterior weather proof emulsion paint complete. Make Asian ultima

M & L complete removal of existing treatment of walls and applying two coats of plastic emlusion paint over a coat of 4 to 5 mm thickness POP over plastered surface to prepare the surface even and smooth all as specified and directed. Make Asian royale shyne

M & L complete removal of existing treatment of ceiling and applying two coats of plastic emlusion paint over a coat of 4 to 5 mm thickness POP over plastered surface to prepare the surface even and smooth all as specified and directed. Make Asian royale shyne

M & L complete removal of existing treatment, as preparation of old decorated surface of walls and applying two coats of cement based paint complete.

M&L preparation of old plastered surface and Providing and applying plaster of paris putty of 2-3 mm thickness over plastered surface to prepare the surface even and smooth. complete.

M&L applying two coats of synthetic enamel paint over a coat of primer including preparation of old steel/wooden/concrete surfaces complete all as specified and directed.

S&F in repair Mortice dead lock set with handle (As per sample) 100mm size, 4 lever brass lock and handle size 180mm for door shutter complete all as per sample specified and directed by Engineer-in-Charge.

M & L in repairs for Providing and fixing PVC sheet wall (prelam wood veneers design) panelling of thickness 5 mm consisting of panels having size 1220 mm X 2440 mm stuck on internal framework of 50 mm wide strips of 5 mm thick PVC sheet, the strip should have in there centre a groove of 6 mm thick width and 1 mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval of 10 inches between two pvc strips. The PVC sheets shall be fixed to the wall using 65 mm long MS screws through the groove in the strip by using PVC fasteners; the distance between two screws shall not be more than 200 mm, a groove of 12 mm may be left at the joint of the panel for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strip of 5 mm thick PVC sheet of width 5 mm thick PVC sheet of width 75 mm feathered at the edge shall be stuck at the place where two panels are jointed using solvent compound complete all as specified and directed by Engineer - in - Charge.

S&F brass six lever dead lock suitable for aluminium doors manufactured by Harrison Locks or Godrej as approved

Dismantling roof sheets / wall cladding etc complete all as spcified and as directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated/ style pattern steel sheet/ Plain steel sheet 0.50mm thick fixed to steel frame with self tapping screw (as direced) with rubber washer in roofs , complete all as specified and directed by Engr-in-charge.

S & F steel work in tubular trusses, rafters and posts etc including special shaped washer etc. complete using ERW or induction butt welded Squre/ Rectangular tubes conforming to IS-1161-1979 (grade st-240)all as specified and directed by Engineer - in - Charge.

Demolition of brick work built in cement mortar including all quains, arches, pillers etc and removing debries out site MOD land complete all as speified and directed .

M&L for brick work with sub class B bricks of old size built in cement mortar 1:4 straight or curved on plan exceeding 6m mean radius all as specified and directed

Taking down cement plaster of any description on brick or concrete surfaces of walls or ceiling etc incl. Raking out joints , hacking for key and scrubbing down with water complete all as specified and directed

M&L for 15 mm thick cement plaster in cement mortar 1:4 on concrete or brick surface and finished even and smooth w/o using extra cement all as specified.

M & L for 15 mm thick cement plaster in cement mortar 1 : 6 on fair faces of brick or concrete surfaces including finished even and smooth without using extra cement all as specified.

All as per Item No 64 above but 10 mm thick in cement mortar 1 : 3 in ceiling, all as specified.

M&L for Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete.

M/L for preparation of new plastered surface of walls and applying two coats of OBD over chalk whitening complete all as specified and directed.

M&L for preparation of newly plastered or unplaster surface and applying two coats ofOBD on ceiling, all as specified.

S&F for 110mm bore PVC (SWR) pipe single socketed any length with rubber ring joints laid in trenches or in floor including taking downcomplete all as specifed and directed.

S & F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, from chowkhat, complete all as specified

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed Surface in CM 1:4 & finished with similar specification as exists, complete all as specified

S&F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with and including back filling PCC (1:3:6), type C-0, complete as specified.

S & F 35mm thick 2nd class hard wood factory made Glazed and skelton shutters open rebated and prepared to receive glass, gauge etc edges of framing plain chamfered or rounded fitted with cut & mitred beads for securing glass etc size of members shutter as specified in SSR Part I Section 8, Clause 8.23 (a) supplied and fitted to chowkhats, 35mm thick 2nd class hard wood.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete.

Supply and fix 150mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete.

Demolition of RCC precast jalli of any thickness, complete all as specified.

Providing precast cement concrete louvers and jallies , 35 mm thick including all mouldings type B-0 1:2:4 ( 12.5 mm graded stone aggregate) set in CM 1: 6 complete all as specified and directed.

Dismantling/removing old damaged worn out APP of any thickness incl screed bed or plastering of any thickness and removing the rubish materials outside MOD land at a dumping place earmarked marked by any state govt/municipalities etc any distance complete.

M & L for cement concrete 1 : 2 : 4 type B-0 (using 12.5 mm graded stone aggregate) laid as in padding 35mm average thick over roof slabs for providing proper slope including finishing surface even and fair all as specified.

Material and labour, 15 mm thick cement plaster in CM (1:4) mixed with WPC as per manufacturer’s instructions @ 150 ml per bag of cement on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for Providing and applying SmartCare Damp-proof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibres having sun reflectivity index (SRI) of 105 on top of roof surface in multiple coats @1.5 ltr/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (Dilution with water in the ratio of 3:1) and other coats needs to be applied undiluted. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of engineer-in-Charge. When 2nd coat is wet, the SmartCare Joint tapes (At corners and edges) shall be inserted b/w second coat and third coat to secure corners and edges, let the material ooze out from the tapes corner. Same treatment of SmartCare Damp-proof shall be continued to the parapet walls to better envelope the whole area. The coating shall be terminated carefully to other side of the parapet wall complete all as specified and directed by Engr-In-Charge. Note :- wk shall be carried by authorized applicator.

M&L for dismantling loose concrete cover of RCC slab, columns, beams, chajjas, balconies, stair case and the like as directed, roughening and cleaning concrete surfaces with steel wire brushes, removing of rust from existing steel surfaces with rust removers of SIKKA rustoff 100 applied in two coats @ 0.15 Kg/Sqm per coat of steel surface and cleaning all rust with steel wire brush and washed with water and allowed to dry including S&F welded fabric GI wire mesh or wire, size not less than 75mmx75mm and 3.00 mm dia as reinforcement to concrete. After placing the additional reinforcement, all concrete surfaces shall be thoroughly scrubbed with brushes, washed with water and allowed to dry. To this surface, apply chemical polycrete admixture at the rate not less than 2% by weight of cement and providing minimum 30 mm thick (average thickness) guniting mix (using 1 part of Ordinary Portland Cement, 53 Grade and 2 parts of Ghaggar sand mixed with adhesive/admixture at the rate as directed) with a pressure of 2 to 2.5 Kg per Sqcm by guniting machine and surfaces finished even and fair including necessary padding, shuttering/form work etc and finally applying 5 mm thick cement plaster in CM 1:3 complete all as specified and directed by Engr-in-Charge. Note: (i) Where ever steel reinforcement required rate of the same deemed to be included in the quoted rate. (ii) Work to be executed for upto four storey buildings and in Patch work.

Supply only Liquid water proofing compound complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Brass handles, cast type, polished bright , complete all as specified and directed

S&F in repairs 300mm length Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed

S & F in repair 25mm dia Stain less steel 206 grade drapery rod in gloss finish including all necessary fixing arrangement like clamps, end brackets, end to end bracket complete all as directed and specified.

M & L for dismantling un serviceable water tanks any description exc 500 but not exc 1000 Liters complete all as specified and as directed by the Engineer-in-Charge

All as per item No 89 above but 250 but not exc 500 Liters.

S&F for 1000 Litres capacity rotational moulded polyethylene water storage tanks, triple layer (white colour) (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed by the Engineer-in-Charge

All as per item No 91 above but 250 but not exc 500 Liters capacity.

shiva enterprises

Ashish Sehgal and Co.

Rishi Constructions

Ex Serviceman Enterprises