CERTAIN REPAIR AND MAINTENANCE OF PIPE LINE, SLUICE VALVE, GATE VALVE, ETC FOR OTM AND MD ACCN AND REPAIR OF PUMPS, MOTOR AND ALLIED WORK OF ZONE B UNDER AGE E/M OF GE (EAST) JABALPUR

Amount

Excavation in trenches, not exc 1.5 mtr wide not exc 1.5 mtr deep for fundations, manholes, laying GI/CI pipes etc n.exc 10Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exce 25Cm thick complete all as specified and directed.

Removing excavated soil to a distance not exce 50 mtr and deposited where directed at a level not exceding 1.5 mtr above the starting point all as specified and directed.

Cutting existing cast iron pipes in any position for insert of new pipe/tees, branches etc complete all as specified as following size. Note : If required necessary excavation earth work, returning filling and removal of surplus soil shall be measured and paid separately under relevant item here-in-above.

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

Taking up the following cast iron water mains (including all fittings) incuding flanged ends rubber joints with spigot and socket ends and lead joint including burning out joints and recovering lead of size :- Note : Excavation/earth work shall be measured and paid separately.

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F the following DI pipes with spigot and socket ends centrifugally cast, Class “K-9”, in any length laid in trenches of size complete all as specified and directed. Make : TATA/Keso Ram/Electro Steel.

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

M&L for run lead joints for the following size of pipes complete for water mains with spigot & socket pipes and fittings complete all as specified and directed :-

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F the following rubber tyton joint of size :-

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F rubber gasket joint for flanged end pipe & fittings of following size :-

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F in repairs machanical Gypsum joint ISI marked for spigot end pipe of following sizes :-

300 mm bore

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F 80mm to 300mm bore spigot/flanged/ socketed CI fittings. such as bends (any type radius and angle), tapers, tees, collars & tail piece socket/flanged/spigot etc complete all as specified.

Dismantling/taking out unserviceable sluice valve of size 80mm to 300mm bore dia by opening/cutting rusted nuts, bolts etc all as specified and directed.

S&F the following CI sluice valves both ends flanged and drilled, bonnet wedge stuffing box. Gland trust plate, hand wheel made out of grey CI, complete valve confirming to IS 14846/2000 and its fittings suitable for hydraulic test pressure of 15 Kg/sqcm PN 1.6 ISI marked complete all as specified and directed. Make : Kirloskar/Kartar/Upadhiya/Sant/L&T.

80 mm bore

100 mm bore

S&F the following CI sluice valves both ends flanged and drilled, bonnet wedge stuffing box. Gland trust plate, hand wheel made out of grey CI, complete valve confirming to IS 14846/2000 and its fittings suitable for hydraulic test pressure of 15 Kg/sqcm PN 1.6 ISI marked complete all as specified and directed. Make : Kirloskar/Kartar/Upadhiya/Sant/L&T.

150 mm bore

200 mm bore

250 mm bore

300 mm bore

Dismantling/taking out un-serviceable air release valve/non return/foot valve/fire hydant valve of any size by opening/cutting rusted nuts, bolts etc all as specified and directed.

Supply and fix CI double end flanged and drilled non return valve of size 200 mm PN-1.6 dia ISI MARKED. Make : Kirloskar/Upadhyay/L&T

Supply and fix CI double end flanged and drilled non return valve of size 150 mm dia PN-1.6 ISI MARKED MAKE : Kirloskar/Upadhyay/L&T

Supply and fix CI double end flanged and drilled non return valve of size 100 mm dia PN-1.6 ISI MARKED. Make : Kirloskar/Upadhyay/L&T

Supply and fix CI foot valve, flanged end and drilled of size 150 mm dia ISI MARKED. Make : Kirloskar/ Upadhyay/L&T

Supply and fix CI foot valve, flanged end and drilled of size 100 mm dia ISI MARKED. Make : Kirloskar/Upadhyay/L&T

Supply & Fix Fire hydrant landing stainless steel valve flange type B ( Double head outlet) of size 65 mm complete ISI MARKED.

Supply & Fix CI Fire hydrant, pillar pattern type of size 100 mm dia complete ISI MARKED

Supply and fix cast iron double ball air release valves of size 80mm as per IS 14845, PN rating H-7 ISI marked. Make : Kirloskar/Upadhyay/L&T MAKE

Cutting of road /hard standing for laying /dismentling of pipe line and making good surfaces matching with the existing surface after laying of pipe line.up to 30 cm

S&F in repairs heating element 2000 watt triangular type make of Bajaj/Tosiba/Havells all as specified and directed by Engineer-in-Charge.

Dismantling of existing valve pit and M&L for construction of masonry valve pit (as per drawing No CEJZ/TD/819/91 dated 16/04/91) with the following specification:- Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 1200 x 1200x1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mmx40mmx5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing.

Dismantling of existing valve pit and M&L for construction of masonry valve pit (as per drawing No CEJZ/TD/819/91 dated 16/04/91) with the following specification:- Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 900 x 900x1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mmx40mmx5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing.

Taking up or down the following old unserviceable GI Tubing :- Note :- Excavation/earthwork shall be measured & paid separately.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100mm bore

S&F the followiing GI tubing medium grade with all fittings and fixed complete laid in trenches of size :-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100mm bore

Taking down/removing the following Unserviceable Gate valve/stop valve from water supply lines, closing the opening with plug or preparing for new as required necessary fittings complete all as specified :-

20 mm bore

25 mm bore

40 mm bore

50 mm bore

S&F the followiing Gun metal Globe or Gate valve with iron wheel head, screwed both ends for iron pipe and fixed with required necessary GI fittings complete :- Make : Kartar/Zolto/Sant/Leader

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Taking down/removing unservieable bib taps 15/20mm bore from pipe line/tanks complete all as specified and directed.

S&F 15mm bore bib tap cast copper alloywith crutch/buterfly handle screwed for iron pipe complete all as specified. Make : Prayag/Polytuff.

S&F 15mm bore bib tap standard of PTMT any colour (minimum wt 15mm - 90gms) screwed for iron pipe complete all as specified. Make - Prayag/Polytuff.

Cutting the following existing galvanised iron pipe in position for insertion of new pipe/tees, branches etc.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100 mm bore

S&F in replacement the following stainless steel spindle suitable for following dia of sluice valve complete with stainless steel nut and threading as per sample & directed by Engr-in- Charge :-

300 mm bore sluice valve

250 mm bore sluice valve

200 mm bore sluice valve

150 mm bore sluice valve

100 mm bore sluice valve

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 25/22.5/20 HP Pump Set . (i) Transportation of submersible pump - motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3 Phase ,taking out burnt winding wire, with & including rewinding PVC insulated water proof copper wire with using winding wire of appropriate gauge and turn, providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Eng-in Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, incl cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 25/22.5/20 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer,assembling the pump and motor including testing complete all as specified and directed.

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 17.5HP/15 HP Pump Set .(i) Transportation of submersible pump -motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3phase ,taking out burnt winding wire, with & including PVC insulated water proof copper wire with winding wire of appropriate gauge and turn, providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Eng-in Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, incl cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 17.5/15 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer,assembling the pump and motor including testing complete all as specified and directed.

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 12.5/10 HP Pump Set .(i) Transportation of submersible pump -motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3 Phase ,taking out burnt winding wire, with & including PVC insulated water proof copper wire with winding wire of appropriate gauge and turn,providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Eng-in Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, incl cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 12.5/10 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer,assembling the pump and motor including testing complete all as specified and directed.

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 7.5/5 HP Pump Set .(i) Transportation of submersible pump -motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3 Phase ,taking out burnt winding wire,with & including pre insulated water proof copper wire with using winding wire of appropriate gauge and turn, providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Eng-in Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, incl cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 7.5/5 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer,assembling the pump and motor including testing complete all as specified and directed.

Note for item No 40 to 43 (i) Cost of disconnection of electric connection from LT control panel & starter of submersible pumping set & reconnecting with existing pipe and making electrical connection with panel board & starter shall be included in the quoted rate of these items. (ii) Cost of lowering of submersible pump set of any size after repairs and re-connecting with existing pipe shall be included in the quoted rate of these items. (iii) Cost of spare parts shall be included in the quoted rate of these items. (iv) The contractor shall be repair the submersible pump and motor within 72 hours after receiving the complaint failing which recovery/penalty shall be imposed @ Rs 500.00/day. The same shall be recovered from the RAR/FB.

Taking out of centrifugal pump set 125/100 HP from pump foundation after disconnection from motor and transportation to workshop , dismantling the pump for repair/ overhauling including cleaning of all parts of pump assembly throughly, including machine work of pump shaft inorder to obtain smooth finish including necessary polishing etc and installing back including helium gasket sheet not less then 1mm thick & to the entire satisfaction of engr-in -charge all as specified and directed. Make - Kirloskar/Jyoti. Note:- (i) Spare parts as required shall be measure & paid seperately against the relevant items. (ii) Make/Size of spare parts of centrifugal Pump Set shall be as per existing centrifugal pump set. (iii) Cost of fixing of spare parts shall be incuded in the quoted rate of this item.

Supply only Casing Wear Ring

Supply only shaft sleeve

Supply only Inter Stage Ring-

Supply only Ball bearing SKF - 7310 -/NU411

Supply only Ball bearing SKF - 6310 C3 -/6311

Supply only Bearing cartridge DE

Supply only Bearing cartridge NDE

Supply only shaft sleeve Nuts

Supply only Split Gland

Taking out of centrifugal pump set 60HP/50HP/40HP from pump foundation after disconnection from motor and transportation to workshop , dismantling the pump for repair/ overhauling incluiding cleaning of all parts of pump assembly throughly, including machine work of pump shaft inorder to obtain smooth finish including necessary polishing etc and installing back including helium gasket sheet not less then 1mm thick & to the entire satisfaction of engr-in -charge all as specified and directed. Make -Kirloskar/DSM 125X40 Note:- (i) Spare parts as required shall be measure & paid seperately against the relevant items. (ii) Make/Size of spare parts of centrifugal Pump Set shall be as per existing centrifugal pump set. (iii) Cost of fixing of spare parts shall be incuded in the quoted rate of this item.

Supply only Casing Wear Ring

Supply only shaft sleeve

Supply onlyInter Stage Ring

Supply only Ball bearing SKF - 6306/6307

Supply only Ball bearing SKF - 6309/6310/6312 C3

Supply only Bearing cartridge DE

Supply only Bearing cartridge NDE

Supply only shaft sleeve Nuts

Supply only Split Gland

Disconnecting electrically and disengaging the AC Squirrel cage induction motor 3 phase 415 Vlots, 50 Cycles, and taking out to local workshop induction motor 125/100 HP for repair purpose including complete cleaning,varnishing, reinsulation and greasing and including shifitng back to location as directed, installing, testing and commissioning after repair complete all as specified and directed. Note:- Rewinding will be measure & paid seperately under relavant item of sch.

Disconnecting electrically and disengaging the AC Squirrel cage induction motor 3 phase 415 Vlots, 50 Cycles, and taking out to local workshop induction motor 60/50/40 HP for repair purpose including complete cleaning,varnishing ,insulation and greasing and including shifting back to location as directed, installing, testing and commissioning after repair complete all as specified and directed. Note- Rewinding will be measure & paid seperately under relavant item of sch.

M&L for Rewinding the motor with super enamelled copper winding wire with appropriate same gauge of exsisting coil with similar class of exsisting insulation as recommended by manufacturer with high quality normex insulating paper applying best quality insulating varnish on stator/rotor windings drying them completely, testing the insulations as directed by Engr-in-Charge. Make:Atlas/BWC/Swastik/Chetak

M & L Fully Automatic Star Delta Motor starter 125 HP in sheet-steel enclosure type ML with single phase protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 66-110 complete all as specified. (Make : L&T cat no SS90923 or Equivalent of SIEMENS/schneider).

M & L Fully Automatic Star Delta Motor starter 75 HP in sheet-steel enclosure type ML with single phase protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 45-75 complete all as specified. (Make : L&T cat no SS90913 or Equivalent of SIEMENS/schneider).

M&L Fully Automatic Star Delta Motor starter 50 HP in sheet-steel enclosure type ML with single phase protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 28-42 complete all as specified. (Make : L&T cat no SS 91730 or Equivalent of SIEMENS/schneider).

M&L Fully Automatic Star Delta Motor starter 25 HP in sheet-steel enclosure type ML with single phase protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 13-21 complete all as specified. (Make : L&T cat no SS 91855 or Equivalent of SIEMENS/schneider).

M&L Fully Automatic Star Delta Motor starter 15 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 11-18 complete all as specified. (Make : L&T cat no SS 96257 or Equivalent of SIEMENS/schneider).

M&L Fully Automatic Star Delta Motor starter 12.5 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 9-14 complete all as specified. (Make : L&T cat no SS 96257 or Equivalent of SIEMENS/schneider).

M&L Fully Automatic DOL Motor starter 7.5 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 13-22 complete all as specified. (Make : L&T cat no SS 96228 or Equivalent of SIEMENS/schneider).

M&L Fully Automatic DOL Motor starter 3 HP in sheet-steel enclosure type MF-1. feature (Motor Rating AC-1 Duty, 230V, 50Hz, 1-Ph) and Relay Range 10.5-17.5 .(Make : L&T cat no cs90319kodo or Equivalent of SIEMENS/schneider).

Taking down unservicable existing spare coil/contactor/over load relay/miniprotection relay of any size/capacity.

S & F spare coil for power contactor amp of make L&T/crompton/schneider/bhartiya cuttler complete all as specified.

S & F Thermal over load relay for type ML-2/3 complete all as specified. Make : L&T/Siemens/Havells/ C&S

S & F Thermal over load relay for type ML-6 complete all as specified. Make:L&T/Siemens/Schnieder

S & F Power contactor ML-1.5 , 3 pole rating not less than 40 A with 230 coil complete all as specified. Make L&T/Schnieder

S & F Power contactor ML-2, 3 pole rating not less than 40 A with 230 coil complete all as specified. Make:L&T/Siemens/Schnieder

S & F Power contactor ML-3 , 3 pole rating not less than 40 A with 230 coil complete all as specified. Make:L&T/Siemens/Schnieder

S & F Power contactor ML-4 , 3 pole rating not less than 40 A with 230 coil complete all as specified. Make:L&T/Siemens/Schnieder

S & F Power contactor ML-6 , 3 pole rating not less than 40 A with 230 coil complete all as specified. Make:L&T/Siemens/Schnieder

S & F MINI PROTECTION RELAY with built in earth fault relay ,MODEL NO-MRP300, 8 to 22 amp, 230 v coil complete all as specified. Make:L&T/Siemens/Schnieder

S & F MINI PROTECTION RELAY with built in earth fault relay ,MODEL NO-MRP300, 16 to 44 amp, 230 v coil complete all as specified. Make:L&T/Siemens/Schnieder

S & F MINI PROTECTION RELAY with built in earth fault relay ,MODEL NO-MRP300, 32 to 88 amp, 230 v coil complete all as specified. Make:L&T/Siemens/Schnieder

Taking down unservicable existing MCCB of any size/capacity.

S&F MCCB 250 A 35 KA, 4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB 200 A 35 KA,4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB 160 A 35 KA, 4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB 125 A 25 KA,4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB 100 A 25 KA, 4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB 63 A 25 KA,4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB 63 A 16 KA,4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified Make : L&T / Schneider/Hager

S&F MCCB TP 63 Amps , 415Volts, 35KA, 3 POLE Make: L&T / LEGRAND/ ABB

S&F MCCB TP 100 Amps , 415Volts, 35KA, 3 POLE Make: L&T / LEGRAND/ ABB

S&F MCCB TP 125 Amps , 415Volts, 35KA, 3 POLE Make: L&T / LEGRAND/ ABB

S&F MCCB TP 160 Amps , 415Volts, 35KA, 3 POLE Make: L&T / LEGRAND/ ABB

M&L draining water from OH reservoirs not exc. 18 Mtr head/staging, and cleaning internal portion of tank (bottom and walls) by means coir / wire brush etc. and wash the internal portion of tanks by using bleaching powder @ 25 grams per 1000 Ltrs of water after removing sludge and mud etc to a distance not exc 50 mtr including one coat of synthetic enamel paint on all steel surfaces such as ladder, railing, inlet & over flow CI pipes connected sluice valves of the respective OH tanks/ground level reservoir etc writing letters with white paint (date of cleaning and capcity of tank) on black painted surface of tanks all as directed by Engineer-in-Charge.

100000 gallons capcity

50000 gallons capcity

All as persrl item No 79 here-in-before but exceeding 18 Mtr head / staging for the following :

100000 gallons capcity

50000 gallons capcity

25000 gallons capcity

All as persrl item No 79 here-in-before but ground level reservoir of 50000 gallons cap each tanks devided in two poriton.

All as persrl item No 79 here-in-before but semi underground reservoir/sump of 200000 gallons cap each tanks devided in two poriton.

All as persrl item No 79 here-in-before but semi underground reservoir/sump of 100000 gallons cap each tanks devided in two poriton.

All as persrl item No 79 here-in-before but semi underground reservoir/sump of 50000 gallons cap each tanks devided in two poriton.

All as persrl item No 79 here-in-before but semi underground reservoir/sump of 25000 gallons cap each tanks devided in two poriton.

Taking down unservicable existing Submersible cable from motor/pannel to starter any size/capacity.

S & F PVC Insulated unsheathed Submersible cable 10 sqmm dia three core multistranded bright annealed copper conductor 1100 volts, including taking down conf to IS-694 complete all as specified. Make : Plaza/ Paragon/ Polycab

S & F PVC Insulated unsheathed Submersible cable 16 sqmm dia three core multistranded bright annealed copper conductor 1100 volts, including taking down conf to IS-694 complete all as specified. Make : Plaza/ Paragon/ Polycab

Cutting and threading of existing GI pipe 80 mm dia.

S&F GI long socket suitable for 80 mm dia and 100 mm long.

S&F current sensing single phasing preventer suitable for 01 to 125 HP submersible pump, motor, electrical panels, generator set panel with input voltage 440 volts, frequency 50 Hzs complete all as specified and directed.

Supply and fixing in replacement of aviation /obstruction light fitting LED 12W 240V 50Hz with light dependent senser including,elecrtic connectionand fitted on GI pipe of 40 mm size on 1.0 mtr height grouted on roof of OHT complete all as specified and directed. Make: Bajaj/Halonix/Philips.

Supply and fixing/laying in replacement of aluminium strip of size 25x3 mm as earth continuity conductor provided in between earth test point terminal and upto the equipment incl nuts, bolts and washers complete all as specified and directed.

Supply and fix in replacement LED security light fitting of 90 watt, aluminium pressure dia cast IP 66 with high power LED & LED driver of make CROMPTON / Wipro/Bajaj/Havells.

S&F in repairs GI pipe 'light grade' bracket 32 mm dia- 1.2 m long & 2 set of clamps made out of 30x5mm MS flat & fixed with anchor bolt suitable for 2 x 70 W security light fitting complete all as specified and directed.

S&F in repairs mono block pump 1 HP ,single Phase 230 volt 1200 RPM ,50 Hz for busting of water supply at TS Road (TS 01 to TS 07) with GI pipe fittings complete all as specified and directed.

Schedule of credit amount of Rs. 4,00,245.00 to be deducted during AOC

shri krishna traders

Goodluck Enterprises

SONAL CONSTRUCTION AND ENGINEERS

SHIVALIK ENGINEERING WORKS

ELCON