SMART PERIODICAL SERVICES FOR MD/OTM ACCN AND MAINT AND REPAIRS TO CERTAIN B/R WORKS AT HANGER, RUNWAY, ATC AND OTHER BLDGS UNDER AGE B/R-II AT GE JHANSI

Amount

Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7" /9" to make free from dust, loose paint etc by skilled labour complete all as specified and directed.

M & L for water proof cement based putty @ 1 kg (undiluted) per Sqm of average thickness 1mm over the plastered/ old prepared painted surface of wall and sanding of the putty surface with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface free from dust etc by skilled labour as per the following steps:- Step 1 :- Mix the putty powder by adding water as per manufacturer's instruction and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2 :- Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application finishing the surface even and smooth in level without any undulations. Step 3 :- Allow 6-8 hrs time to dry the putty surface

M & L for one coat of acrylic water based exterior grade primer @ 0.9 litre (undiluted)/ 10sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine and allow 6-8 hours to dry the surface for painting of subsequent coats complete all as specified and directed.

M & L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pickup resistance with low VOC less than 50, Antifungal / Anti Algai properties in two coats @ 1.79 litre (undiluted) / 10 Sqm diluted with water as per manufacturer's instruction applied over primed surface with fully automatic airless spray machine of paint application with a flow speed of minimum 1 litre per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in between subsequent coats of paint complete all as specified and directed. Note for item No. 1 to 4 :- The work for periodical services shall include the following and the rates quoted by the bidders shall include the same :- (a) The work pertaining to periodical services shall be executed by the contractor as per MoU from authorised applicator through manufacturer of the materials like Exterior Emulsion paint, putty etc after approval by the GE. (b) The Contractor shall upload with the documents under cover I "Memoradum of Understanding" (MOU) with at least one of the manufacturers mentioned in the contract, failing which the bid shall be laible to be rejected. (c) Use of Scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures. (d) Removing of Nails, making good holes, cracks etc (e) Work in patches and in narrow / widths, bands, cornices, pilasters etc and cutting in edge of line where necessary. (f) Spreading and removing covering to doors, windows, floors, fittings etc to protect them from splashes. (g) Washing floors, cleaning glass, joinery , electric fittings , wirings etc. Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer-in-Charge. (h) Sample patch of 10Sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work.

M & L for 15 mm thick rendering in CM 1:4 using waterproofing compound @ 3% by weight of cement on other than fair faces of brick walls or concrete surfaces and finishing surface even and fair complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately under respective item.

Supply only Water proofing compound conforming to IS 2645 complete all as specified and directed.

M & L for 15 mm thick rendering in CM 1:6 on fair faces of brick walls or concrete surfaces and finishing surface even and fair complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer complete all as specified and directed .

M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall or ceiling, complete all as specified and as directed.

M&L for preparation of old plastered or un-plastered surface of walls and applying one coat of white wash (lime) complete all as specified and directed.

All as per Ser item No 10 above but on ceiling complete all as specified and directed.

M&L for preparation of existing surface of walls by brush, sand paper, surface repair if required , filling putty in holes etc and applying one coat of oil bound distemper white or any tint complete all as specified and directed.

All as per Ser item No 12 above but applying two coat of oil bound distemper of white or any tint on walls complete all as specified and directed.

M&L for preparation of existing surface and applying a layer of wall care putty on wall or ceiling and applying two coat of Oil bound distemper for complete smooth finish of surfaces complete all as specified and directed .

M&L for preparation of old plastered surfaces and applying a coat of cement based paint on walls, facia , cornice, chajja upto 16 meter height of the bldg, complete all as specified and directed.

M&L for preparation of existing surface and applying two coats of cement based paint upto 16 meter height of the bldg, complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand preparing / rubbing and finally washing with watering and applying two coats of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer upto 16 meter height of the bldg, complete all as specified and directed.

M&L for preparing old or previously treated surfaces of wood or wood based materials of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint to match the existing surfaces, complete all as specified and directed.

M&L for preparing old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for writing or repainting letters or figures (Block, Roman, Italic, Indian) exc 15cm but n.exc 30 cm in height and line of letters figures n.exc 2cm wide (Bldg No / Name ) etc with one coat of synthetic enamel paint all as specified and as directed.

Dismantling Asbestos Cement Corrugated or Semicorrugate and fibre glass of any type in Roof covering, complete all as specified and directed.

Dismantling of Framed timber scantling 40sq cm and over in section in any position complete all as specified and directed.

Dismantling of Framed timber fillet, rails, post, rafters, purlin etc n. exc 40sq cm in section in any position complete all as specified and directed.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed.

S& F in replacement 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, Hanger wall etc fixed with L-type or J type or cranked hook bolts in lieu of screw complete all as specified and directed.

S& F of 2 mm thick Fibre corrugated sheeting green coloured with two corrugations side lap fixed with coach screw and washer in view cutter etc fixed with bolts or screw complete all as specified and directed.

Excavating in post holes or similar holes, each not exceeding 0.5 Cum, getting out in Hard/ dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and directed.

M&L PCC Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality B for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

Preparation of New or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide complete all as specified and directed.

M&L for Painting lines, dashes, arrows, letters, etc. on roads, pavements and the like exc 10cm wide with road marking paint, white or golden yellow with adequate No. of coats complete all as specified and directed

M&L for Painting lines, dashes, arrows, letters, etc. on roads pavements and the like n exc 10cm wide with road marking paint, white or golden yellow with adequate No. of coats complete all as specified and directed

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over 1 mm putty and a coat of chalk whitening primer preparating to make the surface to be plain and smooth before primer complete all as sppecified and directed.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

Demolition of cement concrete in ground floor including terrazo flooring and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles 300x 450 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick redering in CM 1:4 on wall complete all as specified and directed.

M&L for jointless Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.complete all as specified and directed.

All as per Ser item No 45 above but in skirting including 10mm thick backing coat in CM 1:4 on wall complete all as specified and directed.

M&L for Virified Ceramic tiles 10-12 mm thick (rectangular) heavy duty step tile, area of each tiles not exceeding 0.42 sqm, in flight and riser of steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.complete all as specified and directed

Dismantling for Stone slabs and tiles of any description or thickness in floors, aprons etc, laid dry and pointed in any mortar, complete all as specified and directed.

M&L for Granite 20 mm thick over including 10 mm thick CM 1:4 (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rubbing and polishing complete all as specified and as directed.

M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection and path laid in alternate panels not more than 3 mtr in length, laid to slope 1:30 finished even and smooth without using extra cement including forming joints 10 mm wide and upto full depth of PCC and filled with bitumen mastic (1:3) 1 part bitumen 85/25 and 3 parts of sand complete all as specified and directed. Note:-Bitumen mastic will measured and paid seperately.

M&L for grade A forming construction joint 30 mm deep x 10 mm wide and filled with bitumen mastic all as specified and directed.

Dismantling water tank and removing to store exc. 250 litres & not exc. 1000 litres capacity of tanks, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed.

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S & F in repairs 20 mm bore Gun-metal, ISI, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

M&L for cutting chases,pinning in brick walls for concealed water tubing n.exc 10cm girth and making good facing where required and pointing in CM 1:3 complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste copling, 32 mm PVC Waste pipe 600mm long complete all as specified and directed

Supply & Fix in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed.

S&F in repair Vitreous China table top wash basin, white or off white, flat back, including single lever extended body basin mixer pillar tap, waste chain, plug, porcelain stopper, CP waste copling and CP bottle trap complete all as approved by Engr-in-charge and directed.

Supply & Fix in repairs Vitreous China wash down water closet pan (single unit), EWC, wall mounted/hung, white or off white coloured including concealed flushing cistern system & matching coloured seat covered fixed, complete all as approved by Engr-in-charge and directed.

Supply & Fix in repairs Vitreous China wash down water closet pan (single unit), EWC, floor mounted, white or off white coloured including flushing cistern system & matching coloured seat covered fixed, complete all as approved by Engr-in-charge and directed.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, low level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore conceald stop cock fancy type,chromium plated with long shank and cup screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all specified and directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as specified and directed.

S&F in repair of PVC waste pipe 32 mm dia 750 mm long for wash hand basin or for kitchen sink, complete all as specified and directed.

S & F in repair Chromium plated shower rose 200 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair SS Towel Rail 600mm Long fixed with and including chromium plated brass screws complete all as specified and directed.

S&F in repair of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as specified and directed.

Taking down eaves gutter and rain water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends with access door of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

Taking down Chowkats or frames Not exceeding 1.5 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm but not exceeding 2.00 Sq. M each complete all as specified and directed.

M&L for mild steel framed work section as in door or gates of angle or other section with gusset plates,rails braces etc /windows chowkhats/Shutter frame of steel gate of grade Fe-290 (Gde E-165) including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

M&L for mild steel hold fast and similar small articles conforming to Fe-290 Gde-165, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (12.5mm graded aggregate) for bed block for fixing of chowkhats, cills ,pre-cast lintel n.exc 1.5mtr,coping,benching etc complete all as specified and directed.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc complete all as specified and directed.

S&F of 30mm thick flush shutter doors, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47 mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified in SSR Part-II 2010 section 8.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F powder coated aluminium window shutter Sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

S&F powder coated aluminium ventilator Luver type with frame , aluminium section weighting 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, side handles fixed to wall with fastener, etc completed all as specified and directed.

S&F aluminium powder coated window guards framed with aluminium window section for window guards 4mm dia expanded shape fixed with wall fastner to opening complete all as specified and directed.

M&L for powder coated aluminium frame for doors, windows, ventilators with one or more rebates, fabricated out of powder coated aluminium hallow square or rectangular section of required size incl necessary joining cleats, fixing screws etc complete, having size of frame for doors 100mm x45mm x 3.18 mm thick; for window 104mm x 45mm x 3mm thick; for ventilators 59mm x 33mm x 2.5mm, complete all as specified and directed.

M&L for powder coated aluminum window shutters, side hung type without sash bars, aluminium sections for frame weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber packing, powder coated aluminum snap beading, screws, powder coated aluminum fittings such as peg stays 150mm long (01 No), hinges type B-21 100mm long (02 No), suitable handle (01 No), complete all as specified and directed.

M&L for powder coated aluminium door shutters, aluminium section for top rail and styles 85mm x 45mm x 2.0mm thick; bottom rail 100mm x 45mm x 2mm thick and lock rail 100mm x 45mmx 2.0mm thick incl necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, powder coated aluminum hinges, powder coated aluminum snap beading, screws etc, complete all as specified and directed.

S&F of glass, tinted type, 5.0 mm thick, each panes not exc 0.5 sqm, suitable for aluminium window / Ventilators / door opening and similar work, complete all as specified and directed.

S&F mortice lock of size 100mm, 4 lever type, duly fixed in aluminium door, complete all as specified and directed.

M&L for double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

M&L for aluminium (Extruded section) body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 60 to 80 kg complete all as specified and as directed.

S&F 18/19mm thick pre-laminated particle board , exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work for cupboard shutter complete all as specified and directed.

S&F in repair Block boards 18/19mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work complete as per the specifications and as directed.

S&F Continuous (piano) hinges, mild steel, 30 mm width of flap (when open), bright finish or electrogalvanised, complete all as specified and directed

S&F magnetic catcher for fixing in cupboard, to hold the shutter in closed position, complete all as specified and directed.

Taking down Wall panelling and similar work of any type incl removing to store or from store complete all as specified and directed.

S&F of 5 mm thick PVC wall panelling of wooden texture and of any other shade as approved by Engr-in-charge including all accessoaries for fixing into wall, PVC fillets, PVC strips solvent, epoxy, corner and top finishes with beading, complete all as specified and directed.

S&F of 100mm SS butt hinges ISI marked and fixed with screws or welded to angle frame, complete all as specified and directed.

S&F of 75mm SS butt hinges ISI marked and fixed with screws or welded to angle frame, complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of 200mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast D type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F for Door stopper 140 mm of aluminium alloy body anodised with tongue of rubber bush at one end fixed to door complete all as specified and directed.

S&F Rubber bush of 25mm long fixed to door complete all as specified and directed.

S&F 125 mm Hasp and staple, SS including bolt to hinge plate and fixed with screws complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 3mm thick sheet glass frosted/figured and pin headed glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M&L in repair for Aluminium anodised curtain rod 25mm dia with caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work complete all as specified and directed.

Supply only integral liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as specified and directed.

M&L for RCC 1:2:4 (Nominal Mix)(20 mm stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Form work to flat soffits of suspended slabs such as roof slabs, floor slabs and lintels, landingand similar work n exc 200mm thick complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed.

Demolition existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime concrete etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in padding levelling etc and roof kerbs with liquid water proofing solution finished even and fair with proper slope as prepatory works to water proofing treatment complete all as specified and directed. Note:-liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solutionmeasured and paid seperate item.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions with torch applicationcomplete all as specified and directed with following course of description below:- (a) After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based cement grout. After the surface is repaireds the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain out lets a grove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/SM to be applied on prepared surface, till the surface is property. impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane.

M&L for Apply a coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP membrance, complete all as specified and directed.

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished, complete all as specified and directed.

Dismantling of wall / ceiling boards of any thickness including cover fillets etc, complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh including two coat distemper over a coat of putty to finish the ceiling complete all as specified and directed. Note: The cost of fillets, metal frame work and G.I. wire mesh are incl in quoted rate.

Demolition of brick/stone masonary built in cement mortar incl all quoins arches pillars etc complete all as specified and directed.

M&L for brick work with sub-class B bricks straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) complete all as specified and directed.

M&L for heavy duty, coloured Endura tiles 400mm x 400mm x 8 to 10 mm thick, for garden path including 20 mm thick screed bed in CM (1:4),as per sample kept in GE office, complete all as specified and directed.

M&L for heavy duty, coloured steps tiles 1200mm x 400mm x 8 to 10 mm thick or not exc 0.50 Sqm area of each tile for riser and step including neat cement slurry and pointed in white or Coloured cement to match including 10mm thick redering in CM 1:4, as per sample kept in GE office, complete all as specified and directed.

S&F of 12 mm thick toughned clear glass door with and including chrome finished profiles, roller hanger, patch fittings, hinges ,handles, handrail etc with and incl all respective accessories and colour NR itching, complete all as specified and directed.

M&L Plain Cement Concrete type B-1 1:2:4 (20mm graded aggregate) as in levelling course and coping benching etc complete all as specified and directed.

S&F of 15 mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

VIJAY BUILDERS

S GOURAV PRAKASH ENTERPRISES

M/s Jagdish Chandra Arora

ROHIT ENTERPRISES