SPL REPAIR TO CERTAIN BLDG AND PROVN OF RETAINING WALL NEAR SCHOOL BLDG AT AIR FORCE STATION LONAVLA

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water etc.

M&L for rendering 15 mm thick cement plaster in CM 1:6 on brick work/concrete surfaces finished even and smooth (without using extra lime or cement) complete all as specified.

M&L for rendering 20mm thick cement plaster in CM 1:4 (12mm as 1st coat and 8mm in finishing coat using water proofing compound @ 3% by the weight of cement on brick/ stone surfaces finished fair and even without using extra cement etc complete all as specified and directed.Note : Water proofing compound and will be measured and paid separately.

M&L for rendering 5 mm thick cement plaster in CM 1:3 on ceiling or concrete surfaces finished even and smooth (without using extra lime or cement) complete all as specified.

M&L for preparation of new plastered surface of ceiling and applying three coat of white wash over 3mm thick wall care putty complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying Two coat of oil bound distemper over the alkali resistance priming paint primer over 3mm thick wall care putty complete all as specified and as directed.

Preparing new plastered external surface of wall and applying 2 Coats of Acrylic elastomeric exterior waterproof coating (Dr. Fixit Raincoat or of equivalent make mentioned in list of manufacturers herein after) with extra coat on rain lashed walls, dead walls, projections & Parapet wall top on primed surface with Efflorescence resistant penetrating primer (Dr. Fixit Primeseal or of equivalent make mentioned in list of manufacturers herein after) diluted with 50% water. Work shall be executed by engaging the approved applicator of the manufacturer and as approved by GE.

M&L for complete removal of existing treatment of old painted external surface of wall and applying 2 Coats of Acrylic elastomeric exterior waterproof coating (Dr. Fixit Raincoat or of equivalent make mentioned in list of manufacturers herein after) with extra coat on rain lashed walls, dead walls, projections & Parapet wall top on primed surface with Efflorescence resistant penetrating primer (Dr. Fixit Primeseal or of equivalent make mentioned in list of manufacturers herein after) diluted with 50% water. Work shall be executed by engaging the approved applicator of the manufacturer and as approved by GE.

M&L for complete removal of existing treatment on ceiling and applying three coat of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment of old painted wall surfaces and praparing and applying two coat of oil bound distemper over alkali resistance primimg paint primer over 3.00 mm thick white cement based wall care putty smooth finish etc of approved make & shade on walls and other places complete all as specified and as directed.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Dismantling of floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (desined pattren) (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors laid over 15mm thick screed bed in CM 1:6 . set and jointed in neat cement slurry and pointed in white or coloured cement to match

S&F glazed ceramic coloured tiles (300mmx 450mmx7 mm) in vertical surfaces jointed in neat cement slurry and pointed in white cement. Incl cutting the tiles to the required size whereven required incl mitring the corners etc over 10 mm thick backing coats of cement plaster in CM (1:4) complete all as specified and directed.

M&L for vetrified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed.

M&L for vetrified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in walls skirting etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles.complete all as specified and directed.

M & L for Machine cut kota stone slab flooring 18-20mm thick for floor, window cill, jambs and sofits over and including cement screed base 20 mm thk in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Dismantling stone slabs and tiles of any descritpion or thickness in floors laid bedded in any mortar complete all as specified and directed.

M & L for Rounding to edges of stone slabs on edge, such as in steps, cooking platform, and other similar situations

M&L machine cut granite 16 to 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade

Taking down chowkats or frames n exc 1.5 sqm each with shutters (without taking off shutter from the frame) and removing to store.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4 sqm each with shutters (without taking off shutter from the frame) and removing to store.

Taking down steel/aluminium/wood windows or ventilator of any type any size complete with all fittings

M&L for preparation of new wooden surfaces by applying two coats of synthetic enamel painting over one coat of pink primer on wooden surfaces exceeding 10 cm width or girth including preparation of new/old surfaces.

S&F factory made Solid PVC door frame of size 50mm x 47 mm made out of prelaminated wood grain PVC reinforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and as directed.

S&F factory made solid PVC double door frame of size 50 mm x 95 mm made out of prelaminated wood grain PVC reinforced with MS Square tube all as specified and as directed .

S&F for 35 mm Factory made Moulded prelaminated wood grain pvc door shutter consisting of solid core single leaf flush door of 30 mm thickness,lipped with 15 mm (5mm x 3) thick x30 mm width on the other stiles & bottom rails & 10mm (5mm x 2) thick x 30 mm width on other stiles & bottom rails , The inner panel laminated with 2 mm thick termite proof, water proof and fire resistant molded PVC sheet with 2,4,6 raised panel designs in different plain and / or prelam colours after routing the Moulded design on one side & 2 mm plain and / or prelam PVC sheet on other side using rubber adhesive on flush door & solvent cement adhesive on the PVC Lipping and manufacturer's specification & drawing etc, complete all as specified and directed.

S&F for 35 mm thick Factory made fully glazed solid PVC Door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for stile and 15 mm x 15 mm for top, lock and bottom rail MS frame shall have a coat of steel primer of approved make and manufature MS frame shall be covered with 5 mm thick heat moulded PVC C channel of size 75 mm x 30 mm x 50 mm out of which 10 mm shall be bent at 90 degree towards inner side on front face of the door forming stile, for Top and Bottom rail MS frame shall be covered with 5 mm thick, 100 mm wide PVC sheet out of which 10 mm shall be bent at 90 degree towards inner side on front face of the door. MS frame at Lock rail shall be coverved with 125 mm wide PVC sheet out of which 10 mm both the adjust shall be bent at 90 degree on front face of the door and 75 mm wide PVC sheet shall covered the MS frame at top lock and bottom rail on back side of the door 5mm thick 20 mm croos PVC sheet as gap insert for Top and Bottom rail. PVC sheet beading of 10 mm thickness (5 mm x2), 25 mm wide to be stuck internally in the front face of the stiles and rails of the doors and 10 mm thick ( 5mm x 2), 15 mm wide and PVC sheet beading to be stuck internally in the back side of the stiles and rails of door with solvent cement adhesive,stainless steel wire mess will be fitted exteranlly in the clear face availabe between the stile and rails and fixed between PVC sheet of stiles and rails bent at 90 degree on front face 15 mm x 10 mm, 'L' shape outer beading nailed on stiles and rails at the back side so that the 'L' shape PVC beading can be removed when required for replacement of broken wire mess etc and manufacturer's specification & drawing etc, complete all as specified and dir

Supply and fix aluminium alloy anodised Aldrop sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolt of extruded section of size 300 mm fixed at any position all as specified and directed.

S&F in stainless steel butt hinges, 100mm, medium weight complete all as specified and directed

S&F in extruded aluminium alloy handles, fabricated type of size 150mm in any position complete all as specified and directed.

S&F in aluminium, anodised, barrel tower bolts of extruded section of size 200mm complete all as specified and directed.

140mm Floor door stopper of aluminium alloy body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F Powder coated aluminium three track, three shutter (equal width) type window miniumum 15 micron anodised with frame made of aluminium sections of size 91.80 x 31.75 x 1.2mm and shutters made out of aluminium sections 39.4 x17.7 x 1.2mm without sash bars including necessary jointing cleats, glazing clips, rubber packing, anodised snap beadings, screws aluminium fittings lockings arragngements etc including 4.00mm thick sheet glass for glazed shutters and stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm for wire gauge shutter all as specified and as directed, before.

S&F Powder coated aluminium two track, two shutter (equal width) type window miniumum 15 micron anodised with frame made of aluminium sections of size 91.80 x 31.75 x 1.2mm and shutters made out of aluminium sections 39.4 x17.7 x 1.2mm without sash bars including necessary jointing cleats, glazing clips, rubber packing, anodised snap beadings, screws aluminium fittings lockings arragngements etc including 4.00mm thick sheet glass all as specified and as directed, before.

S&F powder coated aluminium ventilator partly fixed and partly louvered type without sash bar section as per minimum 15 micross anodised including necessary jointing, clip, rubber packing, anodised snap beading crews and 4mm thick pin headed glass etc complete.

S&F 10mm thick aluminium anodised deco grill (DG-104) fitted with 15mm wide 1mm thick aluminium beading

S&F framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165.

M&L for 12mm thick veneered decorative plywood, grade1 (with BWR resin) with decorative face veneers on both faces fixed with screws to timber frame work complete all as specified and directed.

M&L for second class clean sawn hardwood in scantling fixed in timber framed work for cupboardframe complete all as specified and directed.

S&F continuous (piano) hinges 40mm width of flaps (when open) made of stainless steel complete all as specified and as directed

S&F 50mm dia, polished hardwood knobs fixed with screws complete all as specified and as directed.

S&F Ball catches overall length of cover plate 150mm with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified .

Completely removing existing water proofing treatment of any descriptions and any type including top layer of plaster / china mosaic wherever occurs over roof and chhajja surfaces and scrubbing the surface with wire brush and cleaning wash down with water to receive new cement plaster / PCC layer and removing the waste material / debris to a distance exc. 1500m but n.exc. 2000m etc complete all as specified and directed.

M/L for rendering 15mm thick in cm 1:4 on concrete roof and chajja surface to get a uniform level surface for laying of membrane treatment

M/L for PCC 1: 2 : 4 type B-1 (using 20mm graded agg) for PCC padding on RCC roof surface finished even and smoother using extra cement all as specified and directed by Engr-in-Charge.

M/L for applying oil based bituminous primer @ 0.10 Kg/Sqm providing and laying 4mm thick. APP modified water proofing membrane weighing not less than 4kg/sqm re-inforced with non woven polyester matt weighing not less than 160 gm/sqm having softening point not less than 140 degree centigrade longitudinal tensile strength not less than 650 N/Sqm, tearing strength of 180N and with thermal insulation with the mineral / graved finish on upper side and laying with torches application and with 10 cm minimum lap in both direction length wise and width wise all as specified and directed by Engr-in-charge.

M&L for making the grooves 25mm wide and 50mm deep to 'V' section in existing walls/columns over RCC roofs, cleaning out and tacked the polymeric membrane in to the grooves, inserting chajja of PPGI sheet and sealed solidly with a hot mixture of bitumen and clean dry sand in the ratio of 1:1 by weight etc complete all as specified and directed.

Demolition of brick work/stone masonry built in cement mortar including all quoins arches, pillars all as directed.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan exc 6m mean radius, built in cm 1:6 including demolition.

Dismantling of water tanks exc 500 & n exc 1000 ltr capacity and removing to store complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 ltrs capacity hoisted and fixed in position including 25mm dia float ball brass valve and flynut complete, screwed for iron pipe or brass ferrule and fixed all as specified

Taking down 15mm dia bore GI steel tubing and connection including cleaning and making good dismantaled surface complete all as specified.

Taking down 20mm dia bore GI steel tubing and connection including cleaning and making good dismantaled surface complete all as specified.

Taking down 25mm dia bore GI steel tubing and connection including cleaning and making good dismantaled surface complete all as specified.

Dismantling /taking down PVC/Cast iron soil/waste pipes 100mm/75mm bore including all fitting like bends etc.

S&F tubes, ‘medium grade’ galvanised, 15 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

S&F tubes, ‘medium grade’ galvanised, 20 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

S&F tubes, ‘medium grade’ galvanised, 25 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

25 mm dia gate /sluce valave fixed to pipe complete all as specified and directed.

20 mm dia gate /sluce valave fixed to pipe complete all as specified and directed.

S&F Vitreous china wash down water closet (Padestal pattern) pan white including bolts and flush pipe, pedestal pan and trap including connections to drain (or outgoing pipe) and flushing pipe etc including seat cover closed type complete fixed in repairs.

S&F Vitreous china white flat back of size 580x450mm wash basins, vitreous china (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe fixed in repairs.

S&F 10 litre PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.

S&F in repairs Vitreous China half stall urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortatr 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe.

S&F urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60 gms)

S&F in repairs Brass CP central hole basin mixer 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed.

S&F in repairs Brass CP wall mixer 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed.

S&F PVC connection low density polythene pipe 15mm dia, 450mm long, heavy duty with PTMT nuts.

S&F in repairs Bib taps, fancy type, chromium plated with crutch sc-rewed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified and as directed.

S&F in repairs Angle cock, cast copper alloy, fancy type chromium plated, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs toilet paper holder of stainless steel of size 10.5cm X 9cm fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F in repair SS soap dish complete all as specified and directed.

S&F in repairs hand shower (Health Faucet), chromium plated with 8mm dia, 1.00m long flexible tube with wall hook all as specified and as directed. Cat No:- ALD - 573 of Jaquar or equivalent model Manufactured by Esess/ Marc.

S&F in repairs acrylic cabinet mirror of size 450mm X600mm fixed with wooden plugs with cromium plated screw and cup washers, complete all as specified and directed, Make shall be of M/s Commander , M/s Jasmine or equivalent.

S&F 20mm dia towel rail chromium plated 60cm long including bracket fixed with stainless screws complete all as specified.

S&F chromium plated swivel shower rose 125mm dia along with 150mm arms for fixing with 15mm pipe complete all as specified.

S&F in repairs Pillar taps, fancy type, chromium plated, screwed down, high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore complete all as specified and as directed.

Dismantling /taking down PVC/Cast iron soil/waste pipes 100mm/75mm bore including all fitting like bends etc.

S&F PVC (SWR) pipes of dia 110mm bore double socketed in any length with rubber ring joints fixed to walls.

S&F PVC (SWR) pipe of 75mm bore in double socketed in any length with rubber ring joints fixed to walls.

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap complete all as specified and as directed.

S&F PVC (SWR) bends of 75mm bore in radius.

S&F PVC (SWR) bends of 110mm bore in radius.

M&L for PVC Bottle trap having miniumum water seal of 25mm. (Miniumum weight 32mm-260gms/40mm-270gms) of 32mm dia.

S&F PVC (SWR) branch piece double Y equal or unequal of 75mm bore in radius.

S&F PVC (SWR) branch piece double Y equal or unequal of 110mm bore in radius.

S&F PVC (SWR) cowl of 75mm bore in radius.

S&F PVC (SWR) cowl of 100mm bore in radius.

S&F 20mm dia SS curtain rod with fancy brackets with fixing arrangement complete all as specified and directed

Supply integral water proofing compound.

M&L for Preparation of Old steel surface of steel and applying two coats of synthetic enamel paint over a coat of red oxide primer

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for PCC 1:3:6 Mix Type C2 (using 40mm graded stone aggregates), 75mm thick as in plinth protection, complete all as specified and as directed.

Disconnecting existing tanks disconnecting existing tank, setting aside (or lowering if required) for repairs, cheaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repainring, etc. measured separately) , exc 250& not exc 500 litrs tanks complete all as specified.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and as directed.

M&L for pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/manglore tile roof drops fixed with self tapping screws complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F trusses (framed), sunshade frames, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-410-W(Gde-E-250) all as specified and directed by Eng-in-Charge.

Removal of demolished material/ debries from site exc 5km & n.exc 10km as per direction of Engr -in charge complete all as specified and directed.

Dismantling wrought or mild steel work of any description not otherwise provided for

S&F in repairs steel rolling shutters thickness of laths in 1mm, without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete push pull or manual type

S&F in repairs steel rolling shutters thickness of laths in 1mm, without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete gear operated type with bevel gear box and crank handle

S&F Ball bearing for rolling shutters

S&F safety lever locks mild steel with 4 levers for rolling shutters

M&L 80 mm thick Machine pressede precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of Grade M-40 laid over 50mm thick sand cushion complete all as specified

Demolition of reinforced cement Concrete in any description and any position complete all as specified and directed (Old RCC Tank)

RCC in chajja type B1 1:2:4

Formwork to chullah hoods, chajjas, troughs and similar items including edges

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips on slab, MH cover etc. complete all as specified and directed by Engineer-in-charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth; for foundation , etc or for shafts, wells, cesspits, manholes, pair holes, etc n.exc 10 Sqm on plan and n.exc 1.5 in depth and getting out in hard/dense soil etc compete all as specified.

Returning filling in, including, spreading levelling watering and well ramming in layers not exc 25cm in soft/loose soil etc complete all as specified and directed.

M&L for cement concrete type D-2 1:4:8 using 40 mm graded stone aggregate in filling foundation , sub base of floor and mass concrete complete all as specifed and directed.

M & L for walling of random rubble uncoarsed, well bonded, bedded and solidly hearted,built in CM 1:6

M & L for extra over stone walling for hammer dressing (not exceeding 40mm depression) to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) concrete as in Coping & Floor finished etc all as specified and directed.

M & L for Flush pointing to random or polygonal rubble, uncoursed or brought upto courses in CM 1:4.

S & F 75 mm bore PVC (SWR) pipes in any length as in weep holes.

SAI SAMARTH ENTERPRISES

SHAILENDRA B TULSANI

M/s S.D Construction Co