Special repairs to road at equipment park 500 m and special repairs to roads in the unit area Med Regt under GE West at Jalandhar

Amount

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 Sqm and depth exceeding 50mm and not exc 100 mm deep including removal of rubbish material not exceeding 50 m, complete, all as specified and directed.

M&L for 150mm thick (in 2 layers of 75mm thick each, compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated with 8 to 10 ton power road roller to gradient and camber required using granite, trap or basalt stone. Complete all as specified and directed.

M&L for 75 mm thick WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated with 8 to 10 ton power road roller to gradient and camber required using granite, trap or basalt stone. complete, all as specified and directed.

M&L for preparation of WBM surfacess by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally faming the surfaces with gunny bags to remove all loose dirt etc and applying evenly a tack coat with paving bitumin @ 10 Kg per 10 sqm, 40 mm thick (consolidated thickness) semi dense asphaltic concrete with 5.5% binder content, laid with mechanical paver rolled and compacted to required comber and gradient with pneumatic roller. Complete all as specified and directed. Note: Mix shall be prepared in Hot mix plant as per job mix formula obtained from authorised testing lab and laying will be done by mechanical paver.

M & L for applying a tack coat of paving bitumen VG-10 @ 5Kg/10 Sqm of road surface, complete all as specified and directed.

M & L for premix bituminous macadam laid, rolled and compacted to required gradient and camber (consolidated thickness 50mm or less) with paving bitumen VG-30, complete, all as specified and directed .

M& L for Preparing old existing black top surfaces by brushing with wire brushes for removing cacked mud etc sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all dirt and loose material applying evenly a tack coat with paving bitumen VG-10 @ 5kg/10 sqm of road surface, laying Semi dense bituminous premix asphaltic concrete 30mm thick consolidted thickness with 5.5% binder content of bitumen VG-30 by weight of total mix laid using mechanical paver, and rolled to a uniform smooth surface with 8 to 10 ton power road roller to required camber and gradient, complete, all as specified and directed.

M&L for repair to pot holes any depth not exceeding 1 Sqm each including sweeping free from dust and mud, or water scoring sunken surfaces in road path etc cutting around edges, at least 25mm in depth and making good by applying tack coat using paving bitumen VG-10 @ 5 Kg per 10 Sqm, putting in semi dense asphaltic concrete well rammed and sealed with binder using paving bitumen @ 9.8 Kg per 10 Sqm blinded with 0.09 cum stone chipping 6.3mm size and again well rammed (including supply of premixed macadam binder and chippings) and compacted to required gradient with 8 to 12 tonne power road roller, depth of pot hole exceeding 30mm complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete, all as specified and directed.

M&L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS-3262-1989 with special applicator machine all as per manufacturers instruction and accordance with manufacturers specifications, complete, all as specified and directed.

Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. complete, all as specified and directed.

S&F in repair solar delineators made of polycabonate & toughened Auminium alloy body of 80mm dia, height of pole one metre comprises of 4 ultra bright flashing LEDs including 30cm x30cm x 30cm cm size block of PCC (1:2:4) type B1 using 20mm graded stone aggregate. (Make: Dark Eye Cat Part No DA 112 or equivalent from other specified makes in Particular specifications)

S&F in repair High quality ABS Plastic Speed Bump of height 50mm Fixing on road with two highly reflective reflectors moulded in HDPE material are welded with ABS plate having high resistance capacity to withstand severe impacts. (Make: Dark Eye Cat Part No DA 1009 or equivalent from other specified makes in Particular specifications)

M/S Kuldip Construction Co. (BID ID -3348956)