REPAIR/MAINT OF MES INSTALLATION IN THE AOR OF AGE B/R-II UNDER GE(WEST)PATHANKOT

Amount

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site.

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the freme) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and removing from site complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats Note: wire cloth shall be measured separately

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, confirming to IS- 2202(Part-I-1999) , ISI Marked complete all as specified and directed

S&F solid PVC door frame of size 50 x 47mm made out of 5mm wood grain printed & edges will be painted to match with painted sheet, PVC sheet reinforced with MS square tube suppling fixing in opening as per specification & drawing complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 156 of SSR 2010 (Part-II).

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, Length of bolt in 150mm complete all as specified and directed

S&F Aluminium handles, fabricated type, anodised Size of handle in 125mm complete all as specified and directed.

S&F Butt hinges 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-1 complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed Length of bolt in 200 mm complete all as specified.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding to steel frames.complete.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

S&F steel window/Ventilator factory made box type and shutter (double shutter) with sash bar made out of section using flash butt welding, hinges shall be provided to both shutters complete including all fittings including grills made out of 10 mm dia round bars glazing with 3 mm thick oridinary glass, guaging (wire mesh stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts ) and two coat synthetic enamel paint over and including a coat of red oxide primer, atrred hold fasts, PCC bed blocks for fixing hold fast, all as per drg No CEPZ/ TD/032/13 Sheet 1/1 &2/2 including taking out old windows complete all as specified & directed.

S&F in repair 3 mm thick sheet glass ordinary quality and glazing with oil putty wire clips in square n.exc 0.5 sqm in each pane upto tripple story building complete all as specified and directed.

S&F in repair 3mm thick figured glass, pin head type and glazing with oil putty in square n-exc 0.5 sqm in each pane upto tripple story building complete all as specified and directed.

M&L for repairing of Hinges in old steel windows for repairing or welding drilling out old bolts or set screws as required. including repairing for handle pegstag, wiremesh and glass change, painting one coat etc as servicable condition as per directed by Engr-in Charge.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

M&L for one coat of synthetic enamel paint on old treated wooden surfaces of any description not otherwise described over 10cm width or grith including preparation of old surfaces complete all as specified and directed by Engr-in-charge

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

M&L for joint free non skid coloured Ceramic tiles 08mm to 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed.

Demolition of brick work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc including demolition of precast rcc articles and disposal of debris out of MoD land complete all as specified and directed.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed .

M&L for PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) in surface channels and drains complete all as specified and directed by Engr-in-Charge.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete all as specified & directed. (Inner girth only measured)

M&L for precast cement concrete type B-1, 1:2:4 (Using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregate as in sub base finished surfaces of concrete to be even and rough to receive the topping layer complete all as specified and as directed.

M&L for non abrasive paving (endura) tiles 300mm x 300mm x10mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15mm screed bed CM 1:4 to match complete al as specified and directed.Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for Coloured machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-40 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks (50% yellow and 50% Red) & laying pattern approved by GE.

M&L for sand filling under floors or in foundations including watering and consolidation or layer of sand cushioning below interlocking paver block complete all as specified and as directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.(Note:- WPC shall be measured and paid separately)

M&L for Preparing newly plaster surfaces & applying two coats of cement base paint over a Coat of Cement Primer of, any colour complete all as specified & directed.

M&L for complete removal of existing treatment from wall surfaces and applying two coat of cement base paint without any brush marks on the surface complete all as specified and as directed.

M&L for rendering 10 mm thick in cm 1:6 on other than fair faces of brick work , concrete surfaces of wall,finishing surfaces even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

M&L for preparation of newly plastered internally surfaces of wall and applying one coat of wall care putty on the surfaces & making the surface absolutely smooth surface and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion finished without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned complete all as specified and as directed.

M&L for complete removal of existing treatment internally surface of wall and applying minimum 1.5 mm thick wall care putty on the surfaces and making surface absolutely smooth and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned complete all as specified and as directed.

M&L for Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

M&L for complete removal of existing treatment from ceiling surface and applying two coat of white wash on undecorated surfaces without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

M&L for 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

Fixing only 15mm bore old Steel water tubing including all new galvanized fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

M&L for 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

Fixing only 20mm bore old Steel water tubing including all new galvanized fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe

S&F in repair Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S&F in repair Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S&F in repair Ball valves 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 20mm-210 gms)

S&F in repair PVC tank lid/cover for water storage tank of 500 ltrs capacity with fixing arrangement complete all as specified and directed.

S&F in repair 15 mm bore long body CP Bib taps cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe complete all as spd & directed.

S&F in repair CP stop cock/angle valve cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as specified & directed

S&F in repair stop valves (ISI marked), 15mm dia, cast copper alloy,chromium plated fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe all as specified and directed.

S&F in repairs Swan neck CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs Brass CP shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan including P or S trap of bore 125/110 mm (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and wash down water closet complete all as specified and as directed.

S&F in repair viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor complete all as specified and as directed.

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed.

S&F in repairs Viterous China wash basin, white, flat back, size 550x400mm excluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specfied and as directed.

S&F in repair 15mm dia 600 mm long PVC connection including brass check nut at both ends screwed both end for iron pipes.

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, Internal dia of pipe in 75MM/100mm

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia all as specified and directed.

S&F PVC (SWR) bends any radius 110mm dia all as specified and directed.

S&F in repairs 75mm PVC floor trap, ISI marked with cp grating with/without waste pipe hole incl jointing to waste pipe fixed with solvent cement complete all as specified and as directed.

M&L for glass dividing strips 3 mm thick, 38 mm wide and inserted in position to conform to design all as specified and as directed.

Demolition of existing roof treatment of any description such as worn-out tar felt, debris, mortar of any description & any thickness, surface cleaning of all foreign material such as fungus, moss, dust etc. by wire brushing and dusting including disposal of debris out of MoD land then surface levelled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instructions and ensure water does not stand anywhere after Sprinkle water on the roof surface including Applying roof treatment on top of roof with APP modified membrane with non–woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of weight not less than 3.5 Kg/Sqm & thickness not less than 3mm, laid by torch application method with overlap 100mm on length side and 100mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS-3384) @ 0.30 Litre/Sqm complete all as specified. Note: (a)Water proofing treatment shall be provided with APP modified membrane on plastered surface as per manufacturer’s instructions and under strict supervision of manufacturer technical representative. (b) Manufacturer/approved agencies for APP modified membrane shall be as per approved list.

S&F in repair suspended false ceiling system using chicago metallic (E grid)exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) incl dismantling of existing ceiling complete all as directed.

Dismanting of Asbestos cement (corrugated, semi corrugated , etc) sheets in roof coverings etc complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 62,255.00 and any other reduction if any from quoted amount.

OMKAR SHARMA AND CO (BID ID -3107521)

GANDOTRA CONSTRUCTION CO (BID ID -3107960)

M/S PREMI CONSTRUCTION CO (BID ID -3121901)

JP AND CO. (BID ID -3106993)

V K Sharma and Sons (BID ID -3120787)