SPECIAL REPAIRS TO BLDG NO T 5 OR MD ACCN AT RA LINE OF 512 ABW UNDER GE CENTRAL KIRKEE

Amount

Taking down chowkats and frames n.exc 1.5 Sqm each including shutters without taking off shutters from the frame and removing from site complete all as specified and as directed.

Taking down chowkats and frames exc 1.5 Sqm but n.exc 4.00 sqm each including shutters without taking off shutter from the frame and removing from site complete all as specified and as directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet of size 105x60mm for doors, ventilator with single rebates including necessary fixing lugs, hinges, lock strike plate etc. including M & L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) to fill the frame & making good the surface to match with the existing surface complete all as specified and as directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet of size 165x60mm for doors, ventilator with single rebates including necessary fixing lugs, hinges, lock strike plate etc, M & L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) to fill the frame & making good the surface to match with the existing surface complete all as specified and as directed.

S & F For 35 mm thick II class HW wood plain framed , paneled shutter ( two panel) with lock rail and of 9 mm B. W. P. commercial ply or 12 mm veneered particle board with commercial veneering on both stile as per : 1003 ( part I ), kiln seasoned and chemically pressure treated etc. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemicaly pressure treated complete all as specified and as directed.

S & F For 35 mm thick II class HW glazed and skeleton shutters , open rebated and prepared to receive glass, gauze, etc. ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass or gauze etc, sizes of members of shutters as specified in SSR-part-I, Section 8, clause 8.24 (a); etc. complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixing in opening as per manufacturer's instructions and as directed by Engineer-in-Charge. complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position unframed work complete all as specified and as directed

M & L for second class hard wood, clean sawn, in scantlings 40 sqcm and over in section, unframed work complete all as specified and as directed.

All as per item No 10.00 above but except timber. (Retrieved material from dismantling shall be used) complete all as specified and as directed.

M&L for Preparing surfaces of wood and wood based materials new or old of any description and girth, not other wise described and treated with two coat of creosote oil complete all as specified and as directed.

S & F Rolled sections as in main and cross beams, hip and jack rafters; columns, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe -410-W Gde E-250 quality A complete all as specified and as directed.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour as approved, having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including dismantling of Single or double layer Mangalore pattern or similar tiles in roofing complete all as specified and as directed.

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour as approved, having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified including dismantling of Single layer Mangalore pattern ridge or similar tiles in roofing complete all as specified and as directed.

S&F for MS framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S & F 200mm long Aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S & F Aluminium handles, cast type, anodised of size 150mm, fixed with screws or welded complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S & F ventilator shutters made out of aluminium alloy powder coated standard hollow section for ventilators as per approved sample and as per IS specifications, weighting not less than 0.55 kg/RM and rectangular frames of section 101.6x44.45x3.18mm weighing not less than 2.54kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete all as specified and as directed.

Taking up or down carefully 15mm bore steel water tubing, and connections with fittings including cleaning for re-fixing or removable to store or credit to the contractor complete all as specified and as directed.

Taking up or down carefully 20mm bore steel water tubing, and connections with fittings including cleaning for re-fixing or removable to store or credit to the contractor complete all as specified and as directed.

S&F 15mm bore GI tubing ISI marked of size 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /wall/ceiling and including clips, wall hooks etc, including testing complete all as specified and directed

S&F 20mm bore GI tubing ISI marked of size 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /wall/ceiling and including clips, wall hooks etc, including testing complete all as specified and directed

Refixing only 15mm bore GI tubing ISI marked of size 'medium grade' with and including new all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /ceiling and including clips, wall hooks etc, complete all as specified and directed (Note: Old GI pipes as obtained from taking down shall be used under this item)

Refixing only 20mm bore GI tubing ISI marked of size 'medium grade' with and including new all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /ceiling and including clips, wall hooks etc, complete all as specified and directed (Note: Old GI pipes as obtained from taking down shall be used under this item)

S & F in repairs PVC flexible connections 15 mm dia, 600 mm long with brass check nuts complete all as specified and as directed.

S&F in repairs 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair 20mm bore dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repair 25mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 2 5 m m - 455 g m s ) complete all as specified and as directed.

S & F rotational moulded polyethylene water storage tanks of capacity 500 ltrs ( cylindrical vertical with closed top) double layered 'ISI' marked hosted and fixed in position all as specified in SSR part-I (2009) including dismantling of existing water tank complete all as specified and as directed.

S & F in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete bedding complete including making good to floor complete all as specified and as directed.

S&F in repair PVC low level flushing cistern 10 ltrs capacity with float ball valve and bracket including fixing of flush pipe & 15mm dia PVC connector pipe 450mm long with two nos brass fly nuts complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and as directed.

S&F in repairs PVC (SWR) bend with access door of any radius 110mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) bend with access door of any radius 75mm bore complete all as specified and as directed.

S&F for Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S & F in repairs brass CP shower rose 125mm size with swivel joint including fixing to steel pipe 15mm complete all as specified and as directed.

M&L for Chitter Black Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and cutting to shape as required including dismantling existing platform stone complete all as specified and as directed.

S&F in repairs sink made of stainless steel sheeting 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar (1:4) on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm 15mm thick screed bed complete all as specified and as directed.

S & F in repairs vitreous china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but including necessary brackets CP waste coupling and other fittings complete all as specified and as directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.

S&F E-board 'Everest' make 600x600x4mm thick white prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm center to centre securely fixed to the structural soffits by approved hangers at 1200mm maximum center to centre. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600mmx600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction including taking down wall / ceiling board of any thickness including fillets complete all as specified and as directed.

Taking down cement plaster on brick/ block walling including raking out joints, hacking for key, scrubbing down with water etc removing debries outside the MD land complete all as specified and as directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of surfaces walls in CM (1:4) finished even and smooth (without using extra cement) complete all as specified and as directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of walls surfaces in CM (1:6) finished even and smooth (without using extra cement) complete all as specified and as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles, and precast concrete block walling including removing debries outside the MD complete all as specified and as directed.

.M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving below or above GL including removing debries outside the MD and depositing where directed complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 ( Using 40mm graded stone aggregate) as in foundation filling filling and mass concrete complete all as specified and as directed.

Demolition of Concrete reinforced (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for removing debries (except steel) outside the MD and depositing where directed complete all as specified and as directed.

M&L for RCC types A1 (1:11/2:3) (20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC type A1, (1:11/2:3) (using 20mm graded stone aggregate) as in beam, cantilivers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for RCC type A1, (1:11/2:3) (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces complete all as specified and directed.

M&L for preparing old plastered surfaces of wall including preparation of surfaces and applying two coats of oil bound distemper on wall surfaces complete as specified and as directed.

M&L for preparing new plastered surfaces of wall including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer on wall surfaces complete as specified and as directed.

M&L for Preparation of new surfaces (Plastered or un-plastered) of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for Preparation of old surfaces (Plastered or un-plastered) of walls and applying two coats of cement base paint complete all as specified and as directed.

M & L for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M & L for preparing old wood surfaces of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of new or old steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M & L for 25 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor, pavings etc, finishing the surface fair and even without using extra cement complete all as specified and as directed.

M & L coloured ceramic tiles 400 mm x 400 mm x 7-8mm thick, in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:6 including demolition of existing flooring of any type and description and removing the debris outside MOD land complete all as specified and as directed.

M & L coloured ceramic tiles 400 mm x 400 mm x 7-8mm thick, in skirting or dado set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces including demolition of existing skirting or dado of any type and description and removing the debris outside MOD land complete all as specified and as directed.

M&L for glazed ceramic tiles coloured in vertical surface (300 x 200 x 7mm thick) on walls, set & jointed in neat cement slurry & pointed colour cement to match over and including rendering 10mm thick in cm (1:4) on fair faces of brick work or concrete surfaces including finishing the surface fair and even and dismantling of existing wall tiles of any type and description and removing the debris outside MOD land complete all as specified and as directed.

M&L for PCC 1:3:6 type C1 ( Using 20mm graded stone aggregate) as in plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection including finishing the surface even & smooth without using extra cement complete all as specified and as directed.

M & L for 40 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor, pavings etc, finishing the surface even and smooth with using extra cement complete all as specified and as directed.

M&L for glass dividing strips, 3mm thick and 38mm width, inserted in position to conform to design complete all as specified and as directed.

Demolition and breaking up drain pipes (SGSW/ AC/RCC) including haunching and benching set in cement mortar for 150mm to 200mm dia pipe, including removing debries outside the MD complete all as specified and as directed.

M & L for 150 mm dia (internal dia) RCC hume pipe class NP -2 laid and jointed complete with collars complete laid in trenches and tested complete all as specified and as directed.

M& L for PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in bed to drain pipes 150 mm bore including forming cradles complete all as specified and as directed.

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.50 mtr depth n.exc.10 Sqm on plan for foundation etc. or for manhole / laying of pipe and getting out in any type of soil complete all as specified and as directed.

Returning filling in including spreading , leveling watering and well ramming in layers not exceeding 25 cm thick (soil) complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 mtr above starting point complete all as specified and as directed.

M & L for precast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in manhole covers ,septic tank slab etc. set in CM 1:6 complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FR Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FR Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan point or one call bell point controlled by one, one way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switchs, regulators or bell push and casing capping terminal box for mounting ceiling rose/ holders etc including dismantling and taking down old unserviceable point wiring and fittings and fixtures and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one 5 amps socket point on independent board including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switchs, sockets including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one 5 amps socket point on same board with other switches including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm as earth lead and connected to earth dolly for one 16amps socket (Power) point on independent board including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switches, sockets including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 6.0 sqmm (Nominal area) drawn through in and including PVC casing caping/PVC conduit size with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 6.0 sqmm as earth lead and connected to earth dolly including dismantling and taking down old unserviceable wiring and making good to disturbed surfaces complete all as specified and as directed. NOTE: (a)Two run of cable with one run of earth wire and one run of casing capping/conduit will be measured as one length.

S&F 5 Amp switch piano type single pole one way including dismantling and taking down unserviceable switches complete all as specified and as directed.

S&F socket flush type 6 amps, 5 pin, 230v including dismantling and taking down unserviceable sockets complete all as specified and as directed.

S&F switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v including dismantling and taking down unserviceable switch socket complete all as specified and as directed.

S&F bell push flush type 5 Amp single pole one way including dismantling and taking down unserviceable bell push complete all as specified and as directed.

S&F ceiling rose surface type bakelite three terminal including dismantling and taking down unserviceable ceiling rose complete all as specified and as directed.

S&F flush type electronic fan regulator with 5 step type,120 W, AC 240 Volts, 50 Hz including dismantling and taking down unserviceable fan regulator complete all as specified and as directed.

S&F MCB distribution board, as MCCB incomer, IP 30 protection, Double door, metal enclosure,ETPN, 415 Volts, 4 way complete all as specified and as directed. Make cat No. 5076-60 of Legrand or equivalent of schneider or ABB as approved by GE

S&F MCB distribution board, as MCB incomer, IP 43 protection, Double door, metal enclosure, SPN, 230 Volts, 8 way ETPN complete all as specified and as directed. Make cat part no. 5076-11 of Legrand or equivalent of schneider or ABB as approved by GE

S&F MCB,TPN, 63 Amps, 415 Volts,10 KA complete all as specified and as directed. MAKE- Cat Part No- 4086-83 of Legrand or equivalent of Schneider/ABB as approved by GE

S&F MCB, Single Pole and neutral 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve. Make-cat part no.4086-9 to 4086-17 of Legrand or equivalent of schneider/ABB as approved by GE

S&F MCB, Single Pole 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve. Make-Cat part no.4085-87 to 4085-95 of Legrand or equivalent of schneider/ABB as approved by GE

Supply, assemblying & fixing ceiling fan Energy efficient BEE approved 5 star rated, 1200 mm (48") sweep 230V SP and connecting up complete including provision multistranded, FRLS, copper conductor, flexible, twisted cord of 1.5 Sqmm cross sectional area, of required length from ceiling rose to porcelain connector block of the fan, including suitable fan down rod with suitable FI clamp as per site requirement, nut, bolt & washers including flush type electronic fan regulator with 5 step type,120 W, AC 240 Volts, 50 Hzcomplete all as specified and directed

S&F LED Tube light fitting, 18 watt, CDL, 230 Volts, 4 feet long , complete with all accessories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable including LED lamp and mounting casing box 2 nos+E12 any type including dismantling taking down unserviceable one all as specified and directed. Make-HPL, Cat Part No Pheonix Plus HPLLEDT1818 (CW) or equivalent in Havells/Bajaj/Philips/CG as approved by GE

S&F lamp Holder insulated body with back plate for batten fitting complete all as specified and as directed.

S&F LED lamp 12 watt, CDL, B-22 cap, (Pin type), 230V, PF-0.95 (min) complete all as specified and as directed. Make-HPL/Havells/CG/Bajaj/ Philips as approved by GE

S&F LED security light 25 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20/25mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener including dismantling and taking down unserviceable fitting any type all as specified and directed. Make-CG, Cat Part No LSTS-25-CDL or equivalent in Bajaj /Philips /HPL /Havells as approved by GE

M & L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wire mesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion complete all as specified and as directed.

S&F 25mm bore GI tubing ISI marked of size 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in trenches including taking out old unserviceable pipe complete all as specified and as directed.

Supply and fixing in repairs gun metal globe or Gate valve 25 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and as directed

S&F 40m bore GI tubing ISI marked of size 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in trenches including taking out old unserviceable pipe complete all as specified and as directed.

Supply and lay LT UG cable 3.5 core 50 sqmm XLPE insulated sheathed armoured 1100 volts grade laid in trenches complete including taking out old unserviceable cable complete all as specified and as directed.

Material and labour for dry sand cushioning to underground cables in trenches including spreading, leveling, hand punning and consolidating complete all as specified and as directed. Note: Punned thickness of sand shall be measured for payment purpose.

M & L for reinforced precast concrete cable cover class LV type -1 flat of size 250mm x 150mm x 40 mm for cable protection complete all as specified and as directed.

S.R.M.K Enterprises