Loading
Loading…
Loading…
Tender Value
₹1.2 Cr
EMD Value
₹2.3 L
Closing Date
8 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
TECHNICAL
16 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Note: In case, date of tender inviting is on or after date of statutory deadline for audit of balance sheet of previous FY (i.e. 30th Sept or as further extended for this FY), audited balance sheet of 4th previous year shall not be considered unless concerned CA certifies that balance sheet is not audited yet as on date of invitation of this tender.
The contractor should have valid Electrical Contractor License issued by Govt. and submit along with tender document. If valid Electrical Contractor License is not submitted along with tender document, then offer will be summarily rejected.
16 conditions · 3 needing a document upload
The tenderer shall submit all relevant documents as detailed in para 14 & 18.10 of Tender Form (Second Sheet) of Part I of GCC work-2022.
The tenderer shall submit copy regarding status of firm i.e. sole proprietorship, partnership, Company, Society/Trust etc. and also submit a power of attorney and other relevant documents as detailed in Para no. 15 of Tender Form (Second Sheet) of PartI of attached GCC-2022.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. Following documents shall be submitted by the tenderer:
a) Sole Proprietorship Firm: (i) All documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022.
(b) HUF: (i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC2022.
(c) Partnership Firm: (i) A notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm. (iii) An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were / are partners/members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract. (iv) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022.
(e) Company registered under Companies Act 2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) of GCC-2022.
(f) LLP (Limited Liability Partnership): (i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm / LLP or JV in which they were / are partners / members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022.
(g) Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022.
The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he / they be partner(s) of the firm or any other person, specifically authorizing him / them to sign the tender, submit the tender and further to deal with the Tender / Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association / Board resolution, failing which tender shall be summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he / they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the Power of Attorney is being issued. However, the Power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Apostille certificate.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Contractor should quote only the above/below percentage on estimated value, in the space provided at web portal for the purpose & nowhere else. Financial & Technical conditions quoted at any place other than prescribed space shall not be entertained while evaluating the offer.
Tenderer are required to go through the documents attached along with the tender and submit their bids accordingly.
Electrical work in c/w provision of Distributed Electronics Interlocking at Hisar & Sri Ganganagar station over Bikaner Division.
15-El-BKN-E-Tender-26-27~NWR
15-El-BKN-E-Tender-26-27
Open
Works - General
9 Months
Bikaner, Rajasthan
₹0
₹2.3 L
16 Sept 2026
16 Sept 2026
24 Sept 2026
95 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,15,43,539 | ||
| — | 800.00 | — | — | ||
| 1Supply of material and wiring of LP/TP/FP/Ex. Fan point with 1.5sqmm PVC single core multi-stranded copper wire insulated concealed in stone/brick masonry wall in 19/20 mm PVC conduit with 1.5sqmm PVC wire insulated copper for earth wire 1-way / 2-way switch 5/6A as required and good quality ceiling rose, holder including connection. This item includes modular switch, modular ceiling rose, holder, PVC conduit and required chase as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 3,32,000 | |
| — | 300.00 | — | — | ||
| Supply and fixing 5/6A socket, modular 3-pin 230V including modular switch in the modular board and connection as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 80,700 | |
| — | 240.00 | — | — | ||
| Supply and fixing 15/16A socket, modular 6-pin 230V including modular switch in the modular board and connection as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 72,720 | |
| — | 900.00 | — | — | ||
| Supply and fixing 2 module modular switch board plate for fixing of modular switches - socket with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 1,13,400 | |
| — | 200.00 | — | — | ||
| Supply and fixing 4 module modular switch board plate for fixing of modular switches - socket with sheet metal box of good quality concealed fixing of MS /PVC as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 37,600 | |
| — | 160.00 | — | — | ||
| Supply and fixing 6 module modular switch board plate for fixing of modular switches -socket with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 37,920 | |
| — | 160.00 | — | — | ||
| Supply and fixing 8 module modular switch board plate for fixing of modular switches - socket with sheet metal box of good quality concealed fixing of MS /PVC as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 49,920 | |
| — | 120.00 | — | — | ||
| Supply and fixing 12 module modular switch board plate for fixing of modular switches - socket with sheet metal box of good quality concealed fixing of MS /PVC as per site requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 41,280 | |
| — | 6000.00 | — | — | ||
| Wiring of sub-main with 2x2.5 sqmm PVC insulated, single core, multi-stranded copper wire in PVC conduit concealed and 2.5sqmm PVC insulated, single core, multi-stranded copper wire for earth wire as per spec. This item includes wire, PVC conduit (25 MM) and chase as per requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 4,50,000 | |
| — | 3000.00 | — | — | ||
| Wiring of sub-main with 2x4 sqmm PVC insulated, single core, multi-stranded copper wire in PVC conduit concealed and 4.0 sqmm PVC insulated, single core, multi-stranded copper wire for earth wire as per spec. This item includes wire, PVC conduit (25 MM) and chase as per requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 3,87,000 | |
| — | 2000.00 | — | — | ||
| Wiring of sub-main with 2x6 sqmm PVC insulated, single core, multi-stranded copper wire in PVC conduit concealed and 6.0 sqmm PVC insulated, single core, multi-stranded copper wire for earth wire as per spec. This item includes wire, PVC conduit (25 MM) and chase as per requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 2,82,000 | |
| — | 445.00 | — | — | ||
| Fixing of LED tube light complete. (Fitting will be supplied by Railway). Inspection: Consignee, Inspection charges: None. | — | — | — | 15,130 | |
| — | 90.00 | — | — | ||
| Fixing & commissioning of ceiling fan with nut bolt ensuring all safety aspects. Contractor is responsible for falling of fan within a period of 12 month.( Fan will be supplied by Railway. ) Inspection: Consignee, Inspection charges: None. | — | — | — | 2,430 | |
| — | 90.00 | — | — | ||
| Supply and fixing of modular (2 module) fan regulator electronic type 4-step or more (suitable for BLDC fan) as per specification. Inspection: Consignee, Inspection charges: None. | — | — | — | 38,970 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of single phase, 230 volt 50 Hz wall mounting/bracket fan of sweep 400 mm. Fan should be of reputed make. Inspection: Consignee, Inspection charges: None. | — | — | — | 25,860 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of 36 watt, size 2'x2' LED Panel Light with accessories for mounting as per site requirement. Light should be of reputed make with 5 years warranty. Inspection: Consignee, Inspection charges: None. | — | — | — | 69,700 | |
| — | 20.00 | — | — | ||
| SITC of 4 meter length B Class 50 mm dia GI pipe earth station with digging pit & refilling with charcoal & salt. (Asper specification). Inspection: Consignee, Inspection charges: None. | — | — | — | 29,480 | |
| — | 20.00 | — | — | ||
| Construction & supply of earth pit CC furnished chamber 300 x 300 x 250 mm, 50 mm thick with CI/RCC earth pit cover 300 x 300 x 25 mm with lifting hooked in center. Inspection: Consignee, Inspection charges: None. | — | — | — | 12,900 | |
| — | 400.00 | — | — | ||
| Supply, laying and fixing of 25 x 5mm GI earth strip at 0.5 meter below ground level or on walls/poles / along pipes etc, including connection / termination with GI nut, bolt, washer etc as required (jointing shall be done by overlapping and with 2 sets of GInut bolt & spring washer spaced at 50 mm). Note:- Suitable GI saddle swith screws shall be provided to secure earth strips run on walls /floors etc. Inspection: Consignee, Inspection charges: None. | — | — | — | 65,200 | |
| — | 36.00 | — | — | ||
| Supply and fixing of junction box size 390/388x305/304x170mm comprising of SMP/FRP material with rubber gasket, locking arrangement, zinc passivated earth bolt, etc. Make Sintex or similar with 4 no. aluminum busbar cap 200 Amp., suitable for 415 volt supply requirement. The box shall be fixed robustly with clamps at pole/ wall as per requirement. All the material should be of good quality. Inspection: Consignee, Inspection charges: None. | — | — | — | 80,712 | |
| — | 30.00 | — | — | ||
| Supply, installation, testing and commissioning of SPN DB 12 Way with suitable IP protection having 1 No. RCBO 40 Amp Cap., sensitivity 30 mA in the incoming and in outgoing 06 Nos. 10-32 Amp. SP MCB, 10 kA, 'C' curve, 10KA as required with bus bar, neutral bar and necessary wire sets. As per specification. MCB, RCBO and DB should be as per tech spec. and of same make. Inspection: Consignee, Inspection charges: None. | — | — | — | 2,24,670 | |
| — | 200.00 | — | — | ||
| Supply and fixing of Modular mini MCB SP 25/ 32Amp, C series. Breaking capacity not less than 3 kA of reputed make. Inspection: Consignee, Inspection charges: None. | — | — | — | 55,800 | |
| — | 80.00 | — | — | ||
| Supply, fixing, testing and commissioning of single phase, 230-volt, 50 Hz operating ventilation fan of 300 mm. sweep with louver shutters. Fan should be of reputed make and as per tech. spec. Inspection: Consignee, Inspection charges: None. | — | — | — | 1,84,320 | |
| — | 24.00 | — | — | ||
| Supply of unit maintenance free earth material as per RDSO Specs. No RDSO/PE/SPEC/PS/0/0109 (REV.0) 2008 or Latest. Inspection: Consignee, Inspection charges: None. | — | — | — | 2,44,656 | |
| — | 24.00 | — | — | ||
| Installation of unit maintenance free earth material as per RDSO Specs. No RDSO/PE/SPEC/PS/0/0109 (REV.0) 2008 or Latest. Inspection: Consignee, Inspection charges: None. | — | — | — | 1,03,056 | |
| — | 110.00 | — | — | ||
| Supplying, fixing and commissioning of street light fitting accessories e.g. GI pipe of suitable bore as per fitting, clamps, nuts, bolts, cable etc as per instruction of site engineer. Inspection: Consignee, Inspection charges: None. | — | — | — | 16,170 | |
| — | 110.00 | — | — | ||
| Fixing of Street light complete. (Fitting will be supplied by Railway) Inspection: Consignee, Inspection charges: None. | — | — | — | 13,750 | |
| — | 22600.00 | — | — | ||
| Laying, testing, commissioning & transportation of LT cable in Air/ Pole/Pipe/Trench/wall/cable tray etc. with complete lugs/glands and transportation of cable etc. Note- Cable will be supplied by Rly. from main depot. As per specification. Inspection: Consignee, Inspection charges: None. | — | — | — | 5,19,800 | |
| — | 2700.00 | — | — | ||
| Supply of HDPE pipe conforming to IS 4984:2016, 110 mm dia, PN 6, PE 80 as per requirement. Inspection: RITES, Inspection charges: Borne by Railways | — | — | — | 10,01,700 | |
| — | 2700.00 | — | — | ||
| Laying of HDPE pipe conforming to IS 4984:2016, 110 mm dia, under the ground/road. The work involves laying of HDPE pipe along with transportation. Inspection: Consignee, Inspection charges: None. | — | — | — | 37,800 | |
| — | 22000.00 | — | — | ||
| Supply of HDPE pipe conforming to IS 4984:2016, 50 mm dia, wall thickness 3 mm, PN 6 under the road. Inspection: RITES, Inspection charges: Borne by Railways | — | — | — | 15,18,000 | |
| — | 22000.00 | — | — | ||
| Laying of HDPE pipe conforming to IS 4984:2016, 50 mm dia, wall thickness 3 mm, under the ground/road. The work involves laying of HDPE pipe along with transportation. Inspection: Consignee, Inspection charges: None. | — | — | — | 1,98,000 | |
| — | 600.00 | — | — | ||
| Supply of HDPE pipe conforming to IS 4984:2016, 75/80 mm dia, PN 6, PE 80 as per requirement. Inspection: Consignee, Inspection charges: None. | — | — | — | 57,000 | |
| — | 600.00 | — | — | ||
| Laying of HDPE pipe conforming to IS 4984:2016, 75/80 mm dia, under the ground/road. The work involves laying of HDPE pipe along with transportation. Inspection: Consignee, Inspection charges: None. | — | — | — | 7,800 | |
| — | 2500.00 | — | — | ||
| Laying of Spun/MS/GI/HDPE pipe 100mm to 200 mm by drilling of Horizontal bore by machine in Railway yard/below track/Road. Inspection: Consignee, Inspection charges: None. | — | — | — | 30,95,000 | |
| — | 1880.00 | — | — | ||
| Supply and providing of cable marker- The cable marker shall be made of MS sheet 1.5 mm thick size 150 x 100 mm welded with 12 mm dia MS rod 85 cm long. The lower end of rod should be turned in MS hook shape and attached with the cable at the time of laying. Inspection: Consignee, Inspection charges: None. | — | — | — | 3,32,760 | |
| — | 21300.00 | — | — | ||
| Digging and filling of trench size 0.4 x 0.8 mtr as per spec. (trench work may be on kuchha/pucca land and all type of soil as per site requirement and without protective layer of brick) Surface of trench shall be made good in all respect and satisfaction of site engineer. Inspection: Consignee, Inspection charges: None. | — | — | — | 8,94,600 | |
| — | 2.00 | — | — | ||
| Design, manufacturing, supply, testing, erection and commissioning of LT panel made by 2 mm CRCA sheet with 1 no. Incomer 250A MCCB and Outgoing - 2 no. 4 pole MCCB 125 amps., 2 nos. 4 pole MCCB 63 amps. and 2 nos. 4 pole MCCB 40 amps. with meter & indication LED, copper bus bar etc. as per spec. with foundation. Inspection: Consignee, Inspection charges: None. | — | — | — | 2,70,992 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of fabricated feeder pillar distribution box made of MS sheet 1.6 mm thick size 600mmX300mmX600mm with suitable MS stand copper bus bar of 200 Amp. capacity and 2X63 Amp MCB four pole as per technical specification. Inspection: Consignee, Inspection charges: None. | — | — | — | 1,29,580 | |
| — | 450.00 | — | — | ||
| Supply, laying and fixing of GI pipe medium "B" class (Blue) confirming to IS 1239 part-I for passing incoming and outgoing cable from ground through it size 50 mm dia. Pipe should be of reputed make and as per tech. spec. Inspection: Consignee, Inspection charges: None. | — | — | — | 1,04,400 | |
| — | 100.00 | — | — | ||
| Supply, fabrication and fixing of MS cage made of suitable size MS angle and MS jali 1"x1" to provide protection of pit light /electrical equipment/water cooler with two no. of key locks & two nos hinges including one coat of red oxide and two coats of Enamel paint along with fixing arrangement on existing wall/ rail/pipe by nut-bolt/clamp/washer etc. per specification. Inspection: Consignee, Inspection charges: None. | — | — | — | 7,600 | |
| — | 1.00 | — | — | ||
| Supply of ISI marked self-contained drinking water cooler of 150 Ltrs/Hrs as per GeM PO no. GEMC-511687722504838 dated 4.11.2024 specification, Make Usha, Climatrol, Voltas, Blue star, Sanrian or similar. Inspection: Consignee, Inspection charges: None. | — | — | — | 47,100 | |
| — | 1.00 | — | — | ||
| Supply, fixing, testing and commissioning of RCBO 25A, double pole, four modules, 30mA with Earth leakage, overload and short circuit protection as per spec. Inspection: Consignee, Inspection charges: None. | — | — | — | 2,721 | |
| — | 1.00 | — | — | ||
| Supply and fixing of 4 module metal enclosure for fixing of RCBO as per IEC 61439-3, Suitable for flush mounting and surface mounting with door for IP 54, similar to Legrand model no. 507793 of reputed make. Inspection: Consignee, Inspection charges: None. | — | — | — | 692 | |
| — | 150.00 | — | — | ||
| Supply of materials & laying of perforated GI cable Tray cable Tray Size 100 mm X 50mm with cover and fixing arrangement as per site requirement. . Inspection: Consignee, Inspection charges: None. | — | — | — | 60,000 | |
| — | 150.00 | — | — | ||
| Supply of material and laying of perforated GI cable tray of size 300mm X 50 mm with cover and all fixing arrangements as per specification and as per site requirement. . Inspection: Consignee, Inspection charges: None. | — | — | — | 1,81,500 | |
| — | 150.00 | — | — | ||
| Supply and installation of PVC trunking of size 35mm X 30mm. These PVC Trucking shall be made up of High Quality Rigid Polyvinyl Chloride Material which is Fire Retardant & CE Certified, which adheres to international standards in all process of manufacturing, thus enduring a product which meets the high level of Quality and Safety. The installation work shall be executed to the satisfaction of Site Engineer. . Inspection: Consignee, Inspection charges: None. | — | — | — | 9,150 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCwithACS10.pdf
ATTACHMENT
CableCutJPOBikanerDivision.pdf JPO Cable cut
ATTACHMENT
15-DEIforHSRSGNR.pdf
ATTACHMENT
CableCutJPOBikanerDivision.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .