Provision of Wayfinding/signage at JPNI Airport, Patna

Amount

Traffic Statutory Sign Refer design drawing 1.4aS, 1.4aG - Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Providing and fixing sign face panels 3 mm thick Aluminium sheet fixed to sign structure. White retro-reflective vinyl pasted over edge to edge aluminium sheet. Graphics in plotter cut red Pantone 485C and black Pantone 6C exterior grade opaque vinyl pasted over white retroreflective vinyl. Sign Structure MS square post 50x50, hotdipped galvanised and P.U. painted to match RAL 9006 grouted in ground. The actual structural design of the sign for its stability shall be responsibility of the EP Ccontactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Traffic Information Sign Refer design drawing 1.4bS, 1.4bG Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Providing and fixing sign face panels 3 mm thick Aluminium sheet fabrication, Aluminium sheet fixed to sign structure. White retro-reflective vinyl pasted over edge to edge aluminium sheet. Graphics in plotter cut RAL 5013 exterior grade opaque vinyl pasted over white retroreflective vinyl. Sign Structure The sign mounting frame made up of 25 x 25 x 1.29 mm MS Square section and provided with same material ties at centre of length welded to top and bottom member, provided with holes for fixing to the back surface. All fabrication shall be done using CNC machines. Complete mounting frame to be powder coated to match RAL 9006 duly approved by Engineer-in-Charge. . >> The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. MS square post 50x50, hotdipped galvanised and P.U. painted to match RAL 9006 grouted in ground. The actual structural design of the sign for its stability shall be responsibility of the EP Ccontactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Airline Listing - Announcer Refer design drawing 1.5bS, 1.5bG Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Box Providing and fixing sign box with lasercut Bent Fabrication in 8mm thick clear acrylic with pantone yellowC Vinyl pasted on it. Text in opaque blck vinyl matching with RAL 9011. Complete box excluding bottom side is lited with internal LED lighting. Acrylic fabrication shall have transparent structural supports for obstruction free lighting. Box to be directly mounted on the sign structure. Sign Face Providing and fixing sign face panels 3 mm thick Aluminium sheet fabrication, Aluminium sheet fixed to sign structure with black colour RAL 9011 with a provision of through and through laser cutting for airline branding panel. Airline Branding Panel Logo: Vinyl with printed media pasted on 8mm thick 040 White transluscent acrylic with a backlit provision. Text: Plotter cut opaque vinyl to match RAL 9011 Sign Structure Providing and fixing MS square post 50x50 mm fabrication, hotdipped galvanised and fixed to the ground. Frame to receive the sign faces. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor.Secret fixing methods should be used to fix parts together. Crash Guard Providing and fixing Protection for sign from trollies ,wheeled baggage in 50 mm outer dia stailess steel pipe brush finished fixed with 8 mm thick SS plate bracket. Lighting All internal illumination shall be using Power LED Lights 1.44 watts per modules from LT technology with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Arrival/Departure Zone Marker Refer design drawing 1.6aS, 1.6a G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Providing and fixing entire Sign face all 4 sides, made of printed vinyl flex of high quality, with the letters/pictogram to match Pantone Black 6C and the rest of the vinyl to match Pantone Yellow C. To be mounted onto framework using appropriate clips and edge ties to be perfectly taut with no sagging. Stiching of the vinyl flex should not be visible to the customers, prefereably given at the back side of the box. Suspender Providing and fixing suspension for the signs using Stainless steel Hollow section100mm OD (assuming typical length of 15 ft ), cut, fabricated as per drawing and provided with connectors plates for mounting with holes and entire assembly finished in brush finish as approved by the Engineer -in-chagre. Suspender shall be made to required lengths for each sign for its location after studying the site and ensuring a perfectly aligned and leveled sign installation. This item includes all work done on false ceiling like opening/dismantling/local cutting to pass the suspender and reinstalling/doing good/assembling the same after fixing and installation on the sign. Sign Frame Providing and fixing 25mm x 25mm m.s. square sections hot dipped galvanized and welded together to form a framework. Frame to be directly fixed to the sign suspender. Frame to receive the sign faces. Streching Member Providing and fixing 8mm thick acrylic strips vertically to the sign frame to help stretching the sign face. Bottom panel Bottom MS Panel powder coated in colour to match Vinyl Black of Pantone Black 6C. Lighting All internal illumination shall be using Power LED Lights 1.44 watts per modules from LT technology with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>> The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together.

Facility Announcers - Wall Mounted Refer design drawing 1.7bS, 1.7bG Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Plotter cut Blockout vinyl Pantone Yellow C, vinyl for text Pantone Black 6C as per graphics, pasted over 8mm thick White translucent 040 acrylic. Sign Structure 25mm wide powder coated, colour RAL 9006 aluminium extrusion with inbuilt frame to recieve the sign face. The panel should be made easily openable for maintainance. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Facility Announcers - Building Mounted Refer design drawing 1.7cS, 1.7cG Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Box The sign box shall be made in 18 gauge thick P.U.Painted aluminium in specified blue colour RAL 5013. Router cut, grooved and folded to achieve the desired shape as per drawing fixed with the internal frame structure. Sign Face The sign face shall be made in 18 gauge thick P.U. Painted aluminium in specified blue colour RAL 5013, provided with backlit LED lighting and shall have laser cut profiles to recieve milky white 6mm thk acrylic sheet from back. All panels fixed using counter sunk screws. Sign Structure M .S. square sections 25x25mm hotdipped galvanised and powder coated to match RAL 9006 . Structure to be directly fixed to the wall surface. Structure to receive the sign box and the sign face. Lighting All internal illumination shall be using Power LED Lights 1.44 watts per modules from LT technology with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Facility Announcers - Passenger Amenities Refer design drawing 1.7dS, 1.7dG Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Box 1 Providing and fixing sign box with lasercut Bent Fabrication in 8mm thick clear acrylic with pantone yellowC Vinyl pasted over acrylic with white diffuser film on inside face. Blockout vinyl for text Pantone Black 6C. Complete box excluding bottom side is lited with internal LED lighting. Acrylic fabrication shall have transparent structural supports for obstruction free lighting. Box to be directly mounted on the sign structure. Sign face Providing and fixing sign face with 3 mm thick Aluminium sheet fabrication with black colour RAL 9011, Aluminium sheet fixed to sign structure with a provision of niche for telephone as specified in the drawings. Sign Structure Providing and fixing MS square 50 x 50 mm fabrication, hotdipped galvanised and fixed to the ground. Frame to receive the sign face with 3 mm thick Aluminium sheet fabrication with specifie grey colour, Aluminium sheet fixed to sign structure as specified in the drawings.The actual structural design of the sign for its stability shall be responsibility of the EPC contactor.Secret fixing methods should be used to fix parts together.Secret fixing methods should be used to fix parts together. Lighting All internal illumination shall be using Power LED Lights 1.44 watts per modules from LT technology with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Message 3 Ceiling Hung Directional Sign Refer design drawing 2.1aS, 2.1aG Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinyl form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide Powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with 3M brand dual lock syatem in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign internal Structure Providing and fixing Framewrok of Aluminium 25mmx 25mm hollow square sections. Shall be directly fixed to the sign frame. Suspender Providing and fixing Stainless steel 35 x 35mm Hollow sections (assuming typical length of 1 metre) mounted on slabs/beams/walls. All hardware used for fixing of sign shall be Stainless steel. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Message 5 Floor mounted directional sign - Without FIDS Refer design drawing 2.1b-2G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side. The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 and horizontal cross tie member square sections 75x75mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Information Panel Providing and fixing FIDS (lcd screen 46”) mounted on cross ties with brackets designed for the specific sizes. Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Foundation: Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Message 4 Floor mounted directional sign - Single Refer design drawing 2.1b-3S, 2.1b-3G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl.Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Tension Rod Providing and fixing tension rod in brush finished S.S. with the turn buckle syatem. Tension rod shall be fixed to the sign structure and the sign frame with S.S. gusset plates. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Message 5

Message 3 Floor mounted directional sign - Double Refer design drawing 2.1b-4S, 2.1b-4G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl.Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinyl form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Tension Rod Providing and fixing tension rod in brush finished S.S. with the turn buckle syatem. Tension rod shall be fixed to the sign structure and the sign frame with S.S. gusset plates. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

2.2d-2 Counter mounted facility Announcer - With Screen Refer design drawing 2.2d-2S, 2.2d-2G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 5 mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign face shall be provided with through and through cutout to accomodate 32" FIDS Information Panel / FIDS 32" Digital screens mounted on cross ties internally, with brackets designed for the specified sizes. The screen shall be provided by AAI. Sign Frame Providing and fixing sign frame 100 mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Ceiling Hung Facility Announcer - Information Refer design drawing 2.2e-1S, 2.2e-1G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinyl form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign internal Structure Providing and fixing Framewrok of Aluminium 25mmx 25mm hollow square sections. Shall be directly fixed to the sign frame. Suspender Providing and fixing Stainless steel 35 x 35 mm Hollow sections (assuming typical length of 1 metre) mounted on slabs/beams/walls. All hardware used for fixing of sign shall be Stainless steel. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Ceiling Hung facility Announcer - With Screen Refer design drawing 2.2e-2S, 2.2e-2G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8 mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign face shall be provided with through and through cutout to accomodate 32" FIDS Information Panel / FIDS 32" Digital screens mounted on cross ties internally, with brackets designed for the specified sizes. The screen shall be provided by AAI. Sign Frame Providing and fixing sign frame 100 mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Suspender Providing and fixing Stainless steel 50 x 50 mm Hollow sections (assuming typical length of 1 metre) mounted on slabs/beams/walls. All hardware used for fixing of sign shall be Stainless steel. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Boarding Gates - Wall Projected Refer design drawing 2.2g2-S, 2.2g2-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective over laminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Belt No. sign Refer design drawing 2.2h-S, 2.2h-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign Box Providing and fixing sign box with lasercut Bent Fabrication in 8mm thick clear acrylic with pantone yellowC Vinyl pasted over acrylic with white diffuser film on inside face. Blockout vinyl for text Pantone Black 6C. Complete box excluding bottom side is lited with internal LED lighting. Acrylic fabrication shall have transparent structural supports for obstruction free lighting. Box to be directly mounted on the sign structure. Bottom panel Bottom MS Panel powder coated in colour to match Vinyl Black of Pantone Black 6C. Sign Structure : Type 2 All structural members in SS square post 75 x 75 mm (assuming typical length of 2.7 metre), brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together.

Baggage Screening Pole Refer design drawing 2.2j-1S, 2.2j-1G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Washroom / Drinking Water / Baby care Refer design drawing 2.4a-S, 2.4a-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>> Wall Projected/mounted ((Single side content - Sign Face: acrylic, and Back: 3mm ACP)

Service Areas Refer design drawing 2.4b-G Providing and fixing non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Digitally printed Graphics on vinyl pasted on 3mm thick black acrylic mounted on walls/calddings/ panelllings using VHB Tape

Lift No. Sign Refer design drawing 2.4c-S, 2.4c-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system.The panel should be made easily openable for maintainance. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Poster Size A0 Refer design drawing 2.5aG Statutory Signs Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign Face Digitally printed Graphics on vinyl pasted on 3mm thick black acrylic mounted on walls/calddings/ panelllings using VHB Tape

Poster Size A1 Refer design drawing 2.5bG

Poster Size A4 Refer design drawing 2.5eG

Emergency Direction Signs - Illuminated Refer design drawing 2.6a-G Providing and fixing illuminated emergency signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 6mm thick Laminated acrylic (as specified) having graphics pasted on the inside with transluscent white vinyl pasted over plotter cut Transluscent vinyl. The Plotter cut transluscent vinyl to match the specified colour (colour Pantone XXXX) and of specified make duly approved by the Engineer-in-Charge. Sign Box The sign box 80 mm deep shall be made out of 1.6 mm thick CRCA MS sheet fabricated and provided with same material support channel and ties welded to sign channel. All fabrication shall be done using CNC machines. Sign box shall be provided with openings with Mesh from inside for ventilation. Complete sign box including channel supports are to be powder coated to match RAL9016. Sign box flange receiving the sign face shall be provided with slots to receive the rivets to fix the sign frame. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>> 1) Exit

2) Emergency Exit

Emergency Signs - Photoilluminiscent Refer design drawing 2.6b-G Providing and fixing all Photoluminiscent signs in the dedicated fire escape passages of the airports as per locations given in sign schedules, made of screen printing using artworks provided and with photoluminiscent material as per technical specifications.Screen printing shall be done on self adhesive vinyl and pasted on 2mm thick powdercoated white (RAL 9016) aluminium plate and fixed at location using screws. as per specification and using provided artwork including all operations from procuring the correct materials and made to sizes as specified and approved by the Engineer-in-charge. including all installation activities like marking, alignment and fixing with screws into the wall/cladding/face to the satisfaction of the Engineer-in-Charge.>> 1) Fire equipment signs

2) Fire doors inside

3) Fire doors Outside

4) Emergency escape direction sign

Direction to assembly point Refer design drawing 2.6c-S Providing and fixing Non-illuminated emergency signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Signs graphics in exterior grade plotter cut opaque vinyls, made of screen printing using artworks provided and with photoluminiscent material as per technical specifications.Screen printing shall be done on self adhesive vinyl pasted over panels made out of 3mm thick aluminium,Powder coated in white, mounted over central structure using aluminium rivets. Sign Frame Internal MS structure receiving the signs faces using equal angles, hot-dipped galvanised and welded to the sign post. Sign Post 75 mm OD MS post PU painted to match RAL 9011 grouted in ground with concrete footing as per detail.The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Assembly point Refer design drawing 2.6c-S, 2.6c-G Providing and fixing Non-illuminated emergency signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Providing and fixing Photoluminiscent signs made of screen printing using artworks provided and with photoluminiscent material as per technical specifications.Screen printing shall be done on self adhesive vinyl and pasted on 2mm thick powdercoated white (RAL 9016) aluminium plate and fixed at location using screws. as per specification and using provided artwork including all operations from procuring the correct materials and made to sizes as specified and approved by the Engineer-in-charge. including all installation activities like marking, alignment and fixing with screws into the wall/cladding/face to the satisfaction of the Engineer-in-Charge.>> Sign Frame Internal MS structure receiving the signs faces using equal angles, hot-dipped galvanised and welded to the sign post. Sign Post 100 mm OD MS post PU painted to match RAL 9011 grouted in ground with concrete footing as per detail.The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

SATIN NEO DIMENSIONS PVT LTD

POSHDECOR