SPECIAL REPAIR TO SNCOs MESS (VN) TRANSIT BLOCKS AT AF STN PUNE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving's not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantalling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar

M & L cement concrete type B0 1:2:4 (12.5 mm graded agg) 25mm thick as in sub floors complete all as specified and directed.

M&L for 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6 complete all as specified and directed.

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 6) complete all specified and directed.

M&L for non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm in floors {Superior/Premium quality}, set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 6) complete all specified and directed.

All as per Item No 06 above but as in skirting/dados over and including 10mm thick rendering in CM 1:4 complete all as directed.

M&L Glazed Ceramic Coloured Tiles, 350X250X7mm/450X350X7mm thick in size, set on Vertical Surfaces such as Skirting, Dado,etc,over and including 10mm thick rendering in cement mortar 1:4 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incluidng rubbing and polishing complete including screed bed 15mm thick in cement motar 1:6 complete all as specified and directed.

M&L for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with 10mm thick plaster in CM 1:4 all as specified and directed.

M&L granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in CM (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and as directed.

M&L Rounding to edge of stone slabs granite,such as in steps, cooking platform,and other similar situations complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 15mm dia complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 20mm dia complete all as specified and directed.

M&L for GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors in repairs complete all as specified and directed.

Fixing only 15mm dia tubes, any grade, to walls and ceilings or laying in floors complete all as specified and directed.

M&L for GI tubing 20mm dia medium grade with all fittings & fixtures complete laid in trenches fixed in repairs complete all as specified and directed.

Fixing only 20mm dia tubes, any grade, to walls and ceilings or laying in floors complete all as specified and directed.

M&L for GI tubing 25mm dia medium grade with all fittings & fixtures complete laid in trenches fixed in repairs complete all as specified and directed.

Cutting of existing steel tubing for alternation or addition of 15m m dia pipes all as specified and directed.

Cutting of existing steel tubing for alternation or addition of 20m m dia pipes all as specified and directed.

Cutting chases pinning in making good to facing where required for concealed water tubing and making good in stone/concrete walls complete all as specified and directed by Engr-in-Charge.

S&F vitreous chinaware EWC including connection to drain or outgoing pipe and to PVC flushing pipe, antisyphonage pipe with and including, PVC low level flushing cistern 10 ltr capacity and PVC seat cover etc complete all as directed and specified

S&F in repair 15 mm dia CP brass PVC connection 60 cm long including check nuts etc complete all as specified and directed

S & F wall mixter 3-in-1 system with provision of hand shower complete with 115mm long bend pipe connecting legs and wall flange (wihtout hand and over head shower) all as specified and directed.(Model No FUS-29281 of Jaquar)

S &F Two way bib cock with wall flange 15mm dia all as specified and directed.(Model No FUS-29041 of Jaguar)

S &F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in position complete in all as specified.

M&L in repair for 15 mm bore bib tap chromium plated cast copper alloy with wall flange complete all as specified and directed

Dismantling of PVC water tanks of exc 250 and n.exc 500 ltr capacity and removing to store and all as specified and directed by Engr-in-Charge.

S&F rotational moulded polyethylene double layer water storage tank 500 Litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

S & F in repair PVC low level flushing system plastic valve with inlet ball valve float chain and ball (of capacity 10 liters) ISI Marked incl 32mm PVC flush pipe complete all as specified and directed

S & F vitreous china counter wash basin white flat back size 560X410X180 mm rested on counter including waste coupling and PVC waste pipe 75 cm long connecting to PVC connection etc complete all as specified.

M&L Centre hole basin mixer without pop up Pillars taps fancy type cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia fixed as in repairs

S&F in repair angle valves fancy,cast copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed.

S& F looking mirror for counter wash basin of desired shape etc complete all as approved and directed by Engr-in-Charge.

S &F in repair brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges all as specified and directed.

S & F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed bothends for iron pipe

S & F 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed bothends for iron pipe

S &F Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union all as specified and directed.

S &F in repair 15mm dia stop valves cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iorn pipe or for unions and fixed (concealed type) all as specified and directed.

S&F sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, waste pipe and coupling and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified and directed.

S & F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) all as specified and directed

S&F CP soap case all as specified and directed

S&F stainless steel kitchen plate rack of 0.65 mm thick of approved make with plugs, washers, over all size 750mm x 600m complete all as specified and directed.

Demolition and breaking up drain pipes Upto 150 mm bore (Salt glazed ware /PVC/ AC or Reinforced concrete) set in cement mortar

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors

Ditto all as per item No 48 as above but 110mm dia

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed on walls

Ditto all as per item No 50 as above but 110mm dia

M&L for PVC (SWR) bends of any radius with oval access door of 75mm dia

ditto All as per item No 52 as above but 110mm dia

S &F 75mm dia of PVC (SWR) junction single T equal or unequal all with acess dooras specified and directed.

S &F 110mm dia of PVC (SWR) junction single T equal or unequal all with acess dooras specified and directed.

M&Lfor PVC (SWR) vent cowl of 110mm dia

S&F in repair PVC SWR floor trap of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4).

S & F Grating doom 100mm dia of Stainless steel with holes for waste pipes all as specified and directed. (Make Prayag Cat part No FT -06)

S & F Grating doom 100mm dia of stainless steel all as specified and directed. (Make Cat part No FT -05 of prayog)

S&F in repair PVC SWR Nahani trap of diameter of outlet 75 mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) etc complete all as specified

S&F in repair PVC SWR Gully trap of diameter of outlet 75 mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) etc complete all as specified

Demolition RCC of any description and in any position not otherwise specifically provided for complete all as specified and directed

Supply and fix Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc of Fe-410W (Gde E-250 quality A) with and including necessary cutting bending drilling holes welding, rebates etc, complete all as directed by Engr-in-Charge.

S&F pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Taking down chowkat with shutter without taking out shutter from the frame exc 1.5 and n.exc 4 Sqm each

Taking down chowkat with shutter without taking out shutter from the frame n.exc 1.5 Sqm.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as directed .

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

S F Butt hinges, extruded aluminium alloy with galvanised 100 mm long mild steel hinge pin, anodised and fixed, type B-21

S & F 100 mm size Butt hinges, Medium weight, cold rolled mild steel, and fixed all as specified and directed.

S & F continuous (piano ) hinges 30mm width flaps ,mild steel ,bright finish or electrogalvanised all as specified and directed.

S&F 150 mm long, Aluminium barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100 mm long, aluminium barrel tower bolts of extruded Aluminium section complete all as specified and as directed.

S&F 150 mm size handles, Extruded aluminium alloy handles, abricated type, anodised complete all as specified and as directed.

S&F 300 mm long mild steel sliding door bolt, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length 150 mm fixed in floor complete all as specified and as directed .

S & F for 300 mm, MS ordinary rat tail rod pattern Helical door springs including roller and roller plate complete all as specified and directed.

S &F of 125mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified and directed.

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

M & L for 18/19 mm thick Block boards, fixed in repair grade 2 quality, interior grade, commercial type,fixed with screws to timber and nails for storage almirah to the size and pattern as shown in Drg and as directed by Engr-in-charge.

M&L for 0.90mm thick decorative laminate type – I of surface finish (colour & pattern as approved) fixed with approved adhesive as per manufacturer’s instruction finished to approved size for working table all as directed by Engineer-in-Charge.

M&L for 2nd class H.W. plain cover fillets square, rectangular or triangular in section bull nosed, splayed chamfered or rounded on one edge or face in I st class H.W. sectional area n. exc. 6 Sqcm.

S & F for magnetic catcher such as in cupboards etc to catch & support shutters of best quality all as specified

M & L for 165mm x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed all as specified and directed.

M&L for cement concrete type C1 1:3:6 (12.5 mm graded aggregates) for chowkhat filling and hold fast as reqd all as specified and directed.

M & L for Factory made of 35 mm thick glazed and skeleton shutters made of 2nd class hard wood, open rebated and prepared to receive glass gauge edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc for window, ventilator shutters, etc. as specified in SSR Part I, Section 8 clause 8.24(b) and fitted to chowkhat complete all as specified and directed .

M & L for Factory made of 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides: supplied and fitted to chowkats complete all as specified and directed .

S & F Anodised aluminium frame powder coated to (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S& F Anodised aluminium window and ventilator shutters, powder coated fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified all as specified and directed.

Supply and fix sheet glass 3.0 mm thick in glazing with rubber and aluminium beading/packing with rubber gasket complete as specified and directed.

Supply and fix only figured /frosted sheet glass 3.0 mm thick in glazing with rubber and aluminium beading/packing with rubber gasket complete as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F almunium powder coated louvers for ventilltor 4/6 blades fixed to almunium frame complete all as specified and directed .

M&L for Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165

M & L for Preparation of new wooden surfaces of any description having width/girth exceeding 10cm and applying two coat of synthetic enamel paint over pink primer for material and labour complete.

Preparation of new painted surfaces of steel and applying two coat of synthetic enamel paint over one coat of red oxide to steel surfaces of any description not otherwise described over 10 cm width or girth complete all as specified and directed.

Demolition of cement /concrete masonry of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 75mm thick PCC in (1:2:4) type B2 using 20mm graded stone agg as in sunken floor complete all as specified and as directed.

M & L rendering 10mm thick on surface of brick work/concrete surface in CM 1:3 finish smooth with using extra cement and use of WPC complete all as specified directed (Note:- WPC shall be measured and paid separately)

M&L for PCC 1:5:10 type E2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as directed.

M&L for PCC 1:1½ : 3 or Bitumastic Gola with 80/25 bitumen and coarse sand mixer 1:3 by weight 8cm x8cm at the junction of roofing to vertical surface as in sunken or similar work complete all as directed.

M&L for Bitumen blown any grade applied hot, two coats to concrete bedding surface @ 1.5Kg/Sqm per coat as in sunken floor complete all as directed

M&L for polythene flim black 50 micron laid in sunken floor complete all as directed

M&L for spout of 50mm bore GI pipe and projection 450mm clear from outer wall in any length or description with rubber ring joints and fixed in sunken floor etc for drain out logging as in sunken floor etc or similar work complete all as specified and as directed

M&L for 25mm thick PCC 1:2:4 type B0 using 12.5mm graded stone agg as in sunken floor mixed with water proofing comound finished fair and even complete all as specified and as directed (Note:- WPC shall be measured and paid separately)

Taking down existing roof treatment of any type any description and disposing rubbish out of premises complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick works / Concrete surfaces finished even and smooth without using extra cement in cement mortar 1: 4 with using WPC @3% by wt of cement or as per manufacture instructions complete all as specified and as directed ( WPC shall be measured and paid separatly)

M & L for appling bitumenious primer ready mix @ 0.25 kg /sqm on concrete surface by brush or spray gun depending upon the porosity of the surface uniformity wetting and covering entire surface complete all as specified and directed.

M & L for 3 mm thick APP polymer modified bituminous waterproofing membrane sheet HYDROSTOP 3PY-P composed of non-woven polyster mat as core reinforcing media suitably finished with thermo fusible polythylene film on top and bottom side of sheet weight not less than 3.5 kg/sqm apllication with torch-on-method , complete all as specified and directed.

M & L for applying premium quality asphalt based aluminium paint consisting of high grade aluminium blended with water resistant petroleum asphalt @ 160ml/sqm per coat depending upon the age of surface, uniformly wetting and covering the entire surface , complete all as specified and directed.

Supply only integral waterproofing compound.

M&L cement concrete1:2:4, type B0 using 12.5mm graded stone aggregate as in roof rounded or chamfered in edges finished even and smooth with out using extra cement complete all as directed by Engr-in-charge.

Taking down cement plaster on brick/stone/concrete surface including wall tiling and hacking out joints hacking for key scrubbing down with water etc complete

M&L rendering 15mm thick on surface of concrete surface in CM 1:4 and is to be finished even and smooth with out using extra cement with Water profifing compund complete all as specified directed. ( WPC will be measured and paid seperately)

M&L for 5mm thick cement plaster in CM 1:3 on fair faces of concrete surfaces and finishing the surface even and smooth (without using extra cement) etc.

M&L for 10mm thick cement plaster in CM 1:6 on fair faces of stone or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc.

M & L for preperation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

All as per item No. 117 above but on walls.

M&L for prepartion of newly plastered surfaces and appyling two coat of DISTEMPERING WITH 1ST QUALITY acrylic distemper (over a coat of alkali resistant primer) having VOC content less than 50 gm per ltr of approved manufacturere colour complete all as specified and directed.

M & L for prepartion of newly plastered surfaces and applying Two coats of 100% Premium acrylic emulsion paint (Weather Proof) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10sqm over new surfaces complete all as specified and directed.

M&L for 3mm thick wall care putty on wall all as specified and directed by Engr in Charge.

M&L for Preparation of old plastered surfaces/un plastered surfaces including brooming down with steel wire brushing scrapping down smoke spout moulds, moss and efflorescence, salt treating oil and greasy spots etc and applying two coat of white washing on old plastered surfaces of walls all as specified.

M&L for complete removal of existing treatment of walls plastered or unplastered, Washing, rubbing down and two coat of DISTEMPERING WITH 1ST QUALITY acrylic distemper over a coat of alkali resistant primer having VOC content less than 50 gm per ltr complete as per manufactures specifications,all as specified and directed.

All as per ser item No 122 above but on surface of on ceiling /soffits of slabs, chajjas all as specified and as directed at site.

M & L for complete removal of existing treatment of walls plastered or unplastered applying Two or more coats of 100% Premium acrylic emulsion paint ( Weather Proof) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

S & F Harrison rail 20 mm Dia(Curtain rod), of anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc.all as specified and directed.

M&L for precast solid cement concrete block masonry exc 10cm in width built with solid blocks Grade C1 (1:3:6 mix) and set in CM (1:6).

M&L for RCC 1:2:4 (type B0) using 12.5mm graded aggregate as in Slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelve including sup- ports, overhangs, etc. also splays between floors and beams, etc.of rough finished of concrete complete all as specified & directed

M&L for 100 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in sub base of floor and path, plinth protection etc.complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 30 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'A' in plinth protection

Removing building materials etc. (other than spoil ) to a distance of 100m or under, beyond the lead included in the rates, including, loading, unloading and stacking at the destination complete all as specified and directed.

Forming jambs etc, to opering ( to foregoing items), incl cutting toothing and properly bonding into work, also jointing and pointing to match existing work in CM (1:4) complete all as specified and direted.

Cutting down the plant/trees of girth n exc 15cm, from roof/top sides of external walls of bldgs, in chajjas, wall junctions, junctions of GI/CI/AC/PVC pipes and taking out roots entered in wall/slabs, applying emulsion of non toxic chemicals including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and repairing the pipes and joints which was affected by cutting down/taking out process all as specified and as directed for plants / trees located upto a ht of 7.50 mtrs from GL.etc. complete all as specified and directed.

M&L Green Marble work (other than white or black) 18 to 20 mm thick (table rubbed and polished) in cooking platforms, jambs,cills and like over in single peice and including provision of 10mm thick cement mortar (1:4) including pointing in colour cement (1 :2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

S & F Corner glass shelf 300mm with brackets all as specified and directed.

Taking down the existing surface batten type/concealed point wiring of aluminium for Light, Fan, Sockets, power sockets, stair case light pint complete with switch socket regulator, bracket fitting etc and making good distributbed surfaces for wall, floors etc as directed by Engr-in-charge including sorting out serviceable and unserviceable light fitting and keep serviceable fitting in safe gaurd for reuse as required on site.

Taking down the sub main wiring of any dia/sq mm on teak wood batten/ PVC conduit GI earth wire all as specified and directed.

Taking down cearfully by unscrewing the unserviceable DB Boxes, MCB distribution boards SP & TPN with porcelain cutouts etc all as specified and directed.

Material and labour for providing point wiring with two runs of 1.5 Sqmm multi stranded copper conductor FRLSH PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated 1100 Volts grade wire for continuous earthing complete in and including PVC casing and caping with all fittings/fixtures etc and modular PVC Switch box with Cover plate for housing switches/sockets all as specified and directed for one light point controled by one switch

All as per item No 142 above but one Exhaust/Wall mounted/Ceilling point controlled by one regulator/switch

All as per item No 142 above but one 3 pin socket 5 A on independent board.

All as per item No 142 above but one One 3 pin socket 5 A on same board

Material and labour for providing point wiring with two runs of 2.5 Sqmm multi stranded copper conductor FRLSH PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core copper stranded FRLSH PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping, ISI Marked complet for housing one 15 A Switch/sockets complete Note : Metal sunken box, cover plate and frame etc will be measured and paid seprately in respective item.

M & L for sub main wiring with two runs of single core 6.0 Sqmm FRLSH PVC insulated unsheathed multi stranded copper conductor 1100 V grade with colour code and one run of 6.0 Sqmm single core FRLSH PVC insulated unsheathed multi stranded copper conductor green colour cable as earth continuity conductor drawn in & including casing & caping all as directed and specified. (Note : Two runs of 6 Sqmm copper cable & one run of 6 sqmm copper cable including PVC casing & caping shall be measured & paid as one length)

Supply and fix sheet metal enclosure MCB DB double door SPN 12 way 230 V with neutral link with bus bar including fixing concealed in wall including cutting chasing in stone masonary/ Brick masonary and making good the disturbed surface making all necessary incomming and out going connections using proper size copper thimbles complete all as required on site all as specified and directed

S&F MCB SPN 40 to 63 Amp 10 KA 240 Volt, 'C' Curve and electric connections with copper thimbles completed all as specified and directed by Engr-in-Charge.

S&F MCB SP 240 Volt 6 to 32 A 'C' series complete.

Supply and fix Modular switch 1 way 6A, 1 module ISI Marked 230V

Supply and fix Modular socket, 6A-2/3 pin combined 2 module ISI Marked 230V

Supply fix Modular switch 1 way 16A, 1 module ISI Marked 230V

Supply and fix Modular Socket, 6A-2/3 pin combined 2 module ISI Marked 230V

Supply and fix ceilling rose surface type bakelite/PVC three terminal 65x50mm ISI Marked 230V

S & F modular Fan step regular, 120W-2 module ISI Marked 230V.

Supply and fix in replacement high quality indoor Surface and wall mounted batten suitable for 20 Watt T8 Tube rod 4 feet long, including LED retrofit Tube rod 20 Watt T8 Tube rod 4 feet long 6000K colour temperature with extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated industrial grade heavy duty electronic driver having THD<10%. complete with all accessories internally pre-wired and including connecting up with three core 0.5 Sqmm flexible copper conductor cable ceilling rose to fitting terminal.

M&L for providing earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm as earthing lead buried in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers etc made of GI and connected to earthing test point, proving charcoal and common salt all as shown in electrical plate No. 5 of SSR Part I of 2009 & as specified or indicated and testing on completion including exaction/earth work in any type of strata PCC (1:3:6) type C1 earthing chamber, pre cast slabe 50 mm thick in cement concrete (1:2:4) type B1 (reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg/sqm), funnel with wire mesh, watering pipe of 20mm bore medium grade and lugs, including galvanised iron wire 4 mm with GI protection pipe of 15mm medium grade 7.5 meter long, etc complete all as specified.

Taking down the existing street light fitting and Supply & fix (in Replacement) energy saving and envirenmental frindly long life LED Street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics IP65/IP66 road way luminaries with LEDs as light source and lens toughened glass cover and impact resistance of IK07 and electronic driver fixed on wall with and including suitabel dia size bracket as per manufacturer recommendation, bracket 1.5 m long complete with MS flat iron clamps (clamp shall be 40 x 5 mm MS flat), nuts and connection complete all as specified and directed.

Disconnecting & taking down ceilling fan of 1200mm sweep/exhaust fan of 300mm sweep for sevicing strip opening of fan including servicing and greasing complete at site. Re-assembling and refixing to the same/other location after replacing rubber reel, fixing bolts and nuts with lock pins, connectors for complete fan including writing MES No all as required and direction by Engr -in- Charge. Testing complete after servicing and fixing for smooth and noise free operation.

Supply install, test and commioning LT wall mounted indoor Panel board factory fabricated made out of 2 mm thick CRCA sheet & suitable size to accormodate all accessories/fittings, compartmentalized in construction to accommodate incoming and outgoing MCCB, MCB and TPN copper bus bars of rating not less 1.5 times the rated cap of incorner MCCB. The TPN bus bars shall be insulated with colour coded heat shrikable sleeve and shall be mounted on DMC/epoxy insulator. The incoming as well as outgoing MCCBs shall have copper extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. A detachable predrilled gland plate of thickness not less than 2 mm thick should be used at the bottom for entry of armoured cable of adequate size with glands. The above panel shall be front openable lockable/ openable by key. The Panel shall be manucatured from CPRI approved manufacturer of makes stipulated. The cost is inclusive of disconnecting existing cables, taking down existing panel, reconnecting the cables with lugs & glands, Excavation, making good of distribued PCC all as directed and including following MCCB/MCB etc :- (a) Incoming MCCB FP 415 Volt 100 Amps 25 KA - 01 Nos (b) Outgoing MCB SPN 40 Amps, 230 Volts, 10 KA - 10 Nos (c) Outgoing MCB TPN 40 Amps, 415 Volts, 10 KA - 1 Nos (d) Space for fixing of 4 Nos single phase energy meter. Note :- (i) The coste quoted is deemed to be inclusive of taking down of energy meter from existing panel and fixing the same in new panel including necessary connection etc. (ii) Provision should be made in panel to visible of energy meter reading fixed in panel door. (iii) Layout diagram of panel shall be got approved by GE.

M/s Mangesh Nikam (BID ID -3376218)

R k construction (BID ID -3367040)

SHAH BUILDERS (BID ID -3367229)