PROVN OF FORWARD SPEED LANDING AREA FOR ALH AND MT AND CHT CONTROL ROOM WITH ATTACHED TOILET AND BATHROOM AND PARKING SHED INFRONT OF DSI AT DINJAN MIL STN UNDER GE DINJAN

Amount

Surface dressing not exceeding 15 cm deep in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc. and getting out in Soft/ loose soil complete all as specified and as directed.

Returning filling in, including, spreading, levelling, watering and well ramming in layers not exc 25cm in soft / loose soil complete all as specified and as directed.

Removing excavated material soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Excavation in post holes or (similar holes) each not exceeding 0.5Cum, getting out, returning filling in and ramming earth or broken rubber mixed with earth around in layers, not exceeding 25cm watering and removing surplus soil to a distance n.exc 50m and making good surfaces in soft/loose soil complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 (40mm graded stone aggregate) as in foundation of post holes filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (Using 40 mm grade aggregate) in foundation, filling and mass concrete complete all as specified and as directed.

M&L for TMT Bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed not less that 0.90 mm dia or securing with clips) complete all as specified and as directed.

S&F TMT bars 5 to 8mm dia, cut to length, bent to shape required, inlcuding cranking, stirrups, bending spirally for hooping for columns, hooking endsand binding with mild steel wire (annealed) not less than 0.9mm dia, or securing withclips quality complete all as specified and as directed.

M&L for use and waste the form work to sides of concrete foundation, footings plinth beam etc, vertical or to batter complete all as specified and as directed.

M&L for use and waste the form work to sides of pillars, posts, struts, piers, columns, fair finished surface complete all as specified and as directed.

M&L for use and waste the form work to sides and soffits of floor or roof beams, beam, lintels, cantilevers etc, fair finished surface complete all as specified and as directed.

M&L for use and waste the form work to soffits of suspended slab such as roof slab, landings and similar work (Horizontal or sloping) for fair finished surface not exceeding 200 mm thick complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 nominal mix (using 20mm graded aggregate) as in foundation footings, foundation beam,plinth beams and bases of columns basement slabs, and mass concrete complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 nominal mix (using 20mm graded aggregate) as in columns pillers, piers, posts and struts complete all as specified and as directed.

M&L for RCC 1:2:4 type B1, nominal mix (using 20mm graded aggregate) as in beams, cantilevers, bressummers, lintels over 1.5mtr clear span complete all as specified and as directed.

M&L RCC 1:2:4 type B1 (20 mm graded aggregate) as in slabs supported on walls beam and colums in floors, roofs, landind, deck slabs and shelves and the like complete all as specified and as directed.

M&L for brick work with subclass ‘B’ bricks old size straight on curverd on plan exceeding 6m mean radius built in cement mortar (1:6) as directed complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius built in cement mortar (1:4) in half brick thick walls complete all as specified and as directed.

M&L 15mm thick rendering on other than fair faces of brick work or concrete surface in cement mortar (1:6) to be finished even and smooth with out suing extra cement complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:4) to be finished even and smooth with out using extra cement using WPC as per manufacturer's instruction complete all as specified and as directed.

M&L for rendering 5mm thick on concrete surfaces in cement mortar (1:3) and finished surfce even and smooth without using extra cementas as in ceiling complete all as specified and as directed.

M&L for preparing of plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

M&L two coats of oil bound distemper over a coat of primer and putty on plastered wall surfaces including preparation of surfaces complete all as specified and as directed.

M&L two coat of cement base paint over a coat of primer including preparation of surfaces complete all as specified and as directed.

M&L for spreading and levelling in layers not exceeding 25cm thick with well ramming including waterrng as required complete all as specified and as directed.

M&L for hardcore of broken stones or boulders n .exc 15 cm thick of gauge n.exc 63 mm, deposited, sprayed and levelled in layers n exc 15 cm thick watered and rammed to a true surfaces complete all as specified and as directed.

M&L for sand filling under or in foundation inclding watering and consiolidation complete all as specified and as directed.

M&L for 100mm thick PCC type D-2 1:4:8 (using 40mm graded aggregate) as in sub base complete all as specified and as directed.

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade st.-240 complete all as specified and as directed.

S&F for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for mild steel screw bolts (machine made) with heaxgonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, 16 to 20mm dia, but length of bolt exceeding 5.0cm but not exceeding 10.0cm complete all as specified and as directed.

S&F for prepainted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as dirfected.

S&F for prepainted galvalume aluminium zinc coating galvanised ironbased plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as dirfected.

M&L for preperation of new steel surfaces of any desciption over 10 cm in width or girth not other wise descibed and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

M&L for preparing new wooden surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

S&F for 20mm thick, second class hard wood boarding clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc complete all as specified and as directed.

S&F for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 to 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 mtr length) of 0.55 mm thickness having kurled web of 50mm and flange 0f 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed.

S&F for hangers 6mm dia GI (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3mm size 60mm long complete all as specified and as directed.

M&L for seamless calcium silicate ceiling board 12mm thick made out of 1800 X 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specifically formulated jointing compound and 48mm wide fibre tape to provide seam less finish fibre tape to provide eseam less finish (frame work for ceiling shall be measured and paid separately) complete all as specified and as directed.

M&L for two coats of oil bound distemper over a coat of primer on newly ceiling surfaces including preparation of surfaces complete all as specified and as directed.

S&F for pressed steel door frame 125x60mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates complete all as specified and as directed Note : PCC filling of holloow section measured and paid seprately.

S&F for pressed steel door frame 105x60mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates complete all as specified and as directed. Note : PCC filling of holloow section measured and paid seprately.

M&L for water proofing treatment on new RCC roof etc comprising with the following operation and as specified herein below and and as directed :- (a) 15mm thick plastering in cement mortar (1:4) finished even and smooth (b) Preparing & cleaning of fully dried cement plastered surface. (c) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 ltrs per sqm confirming to IS-3384 (d) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm ) shall applied over bituminous primer as specified above. Application of polymeric membrance shall be torch application. The over lap shall be minimum 100mm on transverse direction and 75mm longitudinal direction. (e) One coat of aluminium paint over the APP baed membrane @ 0.11 Kg/Sqm.

S&F for mild steel hold fast and similar articles confirming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for PCC type C-1, 1: 3:6 (using 20mm graded stone aggregate) for cills, hold fast filling of hollow of pressed steel door frame etc complete all as specified and as directed.

S&F for aluminium anodised powder coated (minm thickness of powder coating 50 micron) frame for doors, windows etc with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S&F for aluminium anodised powder coated (minm thickness of powder coating 50 micron) door shutters , aluninium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neopriene paccking, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed.

S&F for anodised aluminium powder coated (minm thickness of powder coating 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55Kg/RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

S&F for 12mm thick prelaminated particle board, interior grade both sides with decorative choice laminations, fixed in to the wall with aluminium clip and bolt, complete all as specified and as directed.

S&F for 150mm floor door stopper of aluminium alloy body and tongue ,anodised, with hard drawn steel spring fixed an floor complete all as specified and as directed.

S&F for 100 mm size brass mortice lock of 4 levers complete all as specified and as directed.

S&F for aluminium anodised (Deco) pattern grill 75x75mm size 7to 8mm thick including suitable aluminium cleats/ plate fixed with steel screws to window frame complete all as specified and as direcetd.

S&F for 35mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamferd or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.24(a), etc complete all as specified and as directed.

M&L in repairs 18/19 mm thick prelaminated particle board, exterior grade, prelimated both sides with decorative cation and fixed with screws to timber frame work including teakwood lipping 6 mm thick fixed withj nails in repairs complete all as specified and as directed.

S&F solid PVC door frames of sizes 50mm x 47mm made out of 5mm but single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement in the frame at site as per specification complete all as specified and as directed.

S&F for 100mm long butt hings medium weight cold rolled mild steel & fixed to chowkats complete all as specified and as directed.

S&F for 150mm long aluminium handle cast type anodised complete all as specified and as directed.

S&F for 200mm long aluminium anodised barrel towe bolt of extruded section complete all as specified and as directed.

S&F for 100mm size Aluminium handles, cast type, anodised complete all as specified and as directed.

S&F for aluminium anodised barrel tower bolts of size 150mm extruded section and fixed complete all as specified and as directed.

S&F for mild steel sliding door bolts, 300 mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

S&F for galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with mastic filling in proportin of bitumen and sand (1:2) complete all as specified and as directed.

Drilling and tapping cast iron water mains (in position) for branch connections of internal dia of 25mm bore galvanised iron pipe complete all as specified and as directed.

S&F for outer diameter of CPVC pipes 20mm bore SDR 11 and plain CPVC SDR 11 including with all fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S&F for outer diameter of CPVC pipes 25mm bore SDR 11 and plain CPVC SDR 11 including with all fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S&F for outer diameter of CPVC pipes 32mm bore SDR 11 and plain CPVC SDR 11 including with all fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Cutting chases, pinning in making good to faceing where required and pointing in cement mortar (1:3) to ends or edges of landing, and cutting chase for concealed water tubing or concealed conduit wiring etc and making good cutting exc 10cm but not exceeding 20cm complete all as specified and as directed.

S&F for vitreous china wash down water closet pan (pedestal pattern) with seat cover white with 'P' or 'S' trap, including and flushing pipe etc complete all as specified and as directed. (excluding fixing bolts, flushing cistern and flush pipe)

S&F for vitreous china squatting pan "Orissa" pattern size 580mmx440mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete all as specified and as directed.

S&F for 10 Litres capacity PVC valveless syphonic action type, flushing cistern low level with inlet, ball valve, float bracket and flush pipe complete all as specified and as directed.

S&F for vitreous china wash basin, white size 550 x 400 mm with brackets, excluding pillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and as directed.

S&F for 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F for 15mm pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nut, screwed for iron pipe and fixed complete all as specified and as directed.

S&F for 15mm bore stop valves, Chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fancey type chromium plate complete all as specified and as directed.

S&F for PVC connection 15 mm size with PTMT nuts length of pipe 600 mm complete all as specified and as directed.

S&F in repairs tubular towel rail brass chromium plated, 20mm dia, D type 60 cm long between flanges complete all as specified and as directed.

S&F for rotational moulded poly ethylene water storage tanks 1000 litres (cylindrical or vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed.

S&F for 20mm bore, ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and as directed.

S&F for brass chromium plated shower rose 125mm dia with or without swivel joints, any size, including fixing to teel pipe or union complete all as specified and as directed.

S&F for 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 350X450X7mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as dado/skirting and facea of side bldg over and including 10mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

M&L for non skid coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm (400X400X7mm) in floor, over 20mm thick screed bed or bedding in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed.

M&L for Non skid coloured tiles 7 to 8mm thick (Square/rectangular) area of each tiles exceeding 0.18sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and 15mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and as directed.

M&L for non skid coloured tiles 7 to 8mm thick (Square/rectangular) area of each tiles exceeding 0.18sqm but not exceeding 0.38 Sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match and 10mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

M&L for 18mm to 20mm thick granite stone slab machine cut, bedded over 15mm thick (1:4) cement mortar scree and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

S&F for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F for grating doom 100mm dia of PTMT, (minimum weight 25 gms) complete all as specified and as directed.

M&L for salt glazed stone ware drain pipes 150mm bore, grade 'A' laid in trenches, jointed and tested complete all as specified and as directed.

M&L concrete 1:3:6 type C-2 (using 40mm graded aggregate) as in bed to 150mm bore pipe including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

M&L for precast reinforced cement concrete 1:2:4, type B1 (using 20 mm graded aggregate) as in cover slab of manholes, septic tank etc, set in cement mortar (1:4) including necessary from,moulds etc and including taking out/removal of existing unserviceable cover slab from manholes/septic tank ccomplete all as specified and as directed. Note : Reinforcement shall be measured andpaid separately

Cutting into existing manholes for connecting new drain , making good to pipe rendering ,cutting out existing bencing for and forming branch channel (1/2 round are 3/4 section)in cement concrete (1:2:4)type B1 smooth finished and reforming bencing as required for 200mm dia complete all as specified and as directed.

S&F for 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor/walls complete all as specified and as directed.

S&F for 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor/walls complete all as specified and as directed.

S&F for 75 mm dia PVC (SWR) bends any radius with access door complete all as specified and as directed.

Bringing approved earth (as approved by Garrison Engineer) from sources outside defence land including all cost such as royalty if any, transportation, taxes if any etc (exceeding 5 KM but not exceeding 10 KM) complete all as specified and as directed. Note : (i) Earth require for the item, shall be supplied by contractor, from out side MOD land of any lead at his own arrangement. (ii) All cost of procurement of earth including cost of transportation, compaction, royalties, tax etc shall be demeed to be included in the unit rate quoted by the contractor. (iii) Total quantity/partial quantity of earth may not be available in Dinjan area. The contractor shall bring the earth outside area and it is advised to quoted the rate considering availability of soil and its lead involved.

Forming embankment including raising spreading in layers not exceeding 30cm thick each layer and rolling and finishing to required size and shape etc, not exceeding 1.5m heigh from base, earth to be obtained from out side MoD land exceeding 1.5 KM not exceeding 15 KM complete all as specified and directed.

M&L for concealed point wiring with 1.5 sq mm (nominal area) single core pvc insulated FR unsheathed multi-standared copper conductor cable (maintaining colour code), 1100 volt grade and including pvc conduitct (size as required site) concealed and sunken terminal boxes with 3 mm hylam sheet top cover of adequate size for mounting switches , sockets , regulators light fitting etc complete with all fitting and accessories fixed to wall /ceiling for one light /fan/call bell point concealed by one switch including one run 1.5 sq mm (nominal area) PVC insulated frame retardant unsheathed multistranded copper conductor cable green in colour for earth continuity conductor connected to common earth point duly completed all as specified and as directed.

All as per item No. 104 here-in-above but on 5 amp 3/5 pin socket outlet on independent board complete all as specified and as directed.

All as per item No. 104 here-in-above but on 5 amp 3/5 pin socket outlet point on same board with other switches complete all as specified and as directed.

All as per item No. 104 here-in-above but wiring with cables of size 2.5 sqmm for wiring & cables of size 2.5 sqmm both as continuous earth wire for one 15 Amps, 3 pin Switch/Socket outlet on Independent board complete all as specified and as directed.

S&F for switch piano, flush type single pole, one way 5 Amp complete all as specified and as directed.

S&F for socket outlet 2 in 1, 5 Amp flush type complete all as specified and as directed.

S&F for switch socket combination 2 in 1, 5 Amp flush type complete all as specified and as directed.

S&F for switch socket combination 5A/ 16A, 5 in 1flush type complete all as specified and as directed.

S&F for ceiling rose, 3 way PVC insulated body complete all as specified and as directed.

S&F for stepped type electronic fan regulator flush type complete all as specified and as directed.

S&F for 18 W surface and wall mounted LED batten with polycarbonate housing and intigrated including the fitting to be fitted on PVC block of suitable size complete all as specified and as directed. Make :Cat No. LUMILINEBS18WLED865SPCWH of Havells /Philips/Bajaj/CG/Wipro

M&L for lamp holder, PVC/ poly carbonate type with black plate suitable for batten fittings complete all as specified and as directed.

S&F for LED Lamp 7 Watt complete all as specified and directed by engineer in charge complete all as specified and as directed. Make : Havells/Philips/Bajaj.

S&F for 25 W LED building security new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminum housing with hight power LED as lighting source and lens imbedded PC Cover having TOP OPENING seperate driver cmpartment with IP 65 protection and inpact resistance of IK07 including clamps/nut bolt/GI pipe for holding the security light complete all as specified and as directed.. Make : Cat No ENDURAPEARLSL25WLED757SASYTOPC Havells/Philips/Bajaj/ CG/Wipro

S&F for fans ceiling complete 230 V,1200 mm sweep BEE 5 star rated Colour white, including fixing arrangement complete all as specified and as directed. Make : Model No Entrust 50-5 star opel white of Crompton/Havells/Usha/Bajaj.

S&F for exhaust fans AC single phase 230/ 240 V of size 380 mm sweep 1 phase 1400 RPM including LOUVER SHUTTER of suitable size complete all as specified and as directed. Make : Model No EXHD380-4-1 of Crompton/Bajaj/Usha.

S&F new Sheet metal enclosure for MCB DB double door single pole & Neutral 4 way, 240 V with common bus bar at incomming end complete all as specified and as directed.

S&F MCB 'C' curve single pole and neutral 6 to 32 Amps with breaking capacity 10 kA, complete all as specified and as directed. Make: Cat No. 408609-17 of Legrand/L&T/Havells.

S&F MCB 'C' series SP 6 to 32 Amps, 240 volts, breaking capacity 10KA, complete all as specified and as directed. Make: Cat No. 4086 09-17 of Legrand/L&T/Havells.

S&F for 1100 volts grade heavy duty cable PVC insulated aluminium conductor, srved with inner sheathing of PVC tape and overall PVC sheathed in service connection's suspended by insulating hangers not more than 1.0m apart including 4mm suspention wire, one twin core cable slat or circular 10.0 sqmm including suitable size bracket for suitable connection/holding of cable complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.0mm GI wire by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no 3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering including the earth pit base in which pit cover rests made up of MS angle iron frame complete all as specified and directed and tested on completion complete all as specified and as directed.

M/S A K BROTHERS

M/s GANDHESWAR PHUKAN

FREEZCON

M/S HAZARIKA CONSTRUCTION

M/S CHANDAN ENTERPRISE

Construction House