Construction of compound wall, Removing Relaying of cuddapah slab Frame work for plant Renv Honey Bee Shed erection of transformer Renv existing ponds and existing fountain Chairs Renv old Toilet Function light arrangmnt Focus light Spot light at KCP

Amount

Boring through the 300mm dia liner tube in all type of soil strata including sea silt or clay sand and weathered rock. The rate should include the removal of bored material, cleaning the loose particles, bailing chiseling and taking all measures to retain the sides and prevent necking of line from bed level excluding installing of lines & driving of liners etc., complete complying with standard specification and as directed by the departmental officers.

Trimming of Pile head of 300 mm dia. Piles upto cut off level and stacking the debris in convenient place and transporting to low lying area inside the fishing harbour within a lead of 1 km as directed by the Engineer's representatives and all associated cleaning of projecting reinforecement etc complete as directed by the department officers.

Providing and placing insitu design mix reinforcement cement concrete of M30 (M.Thirty only) by weight basis using ordinary port land cement (OPC) 43 Plinth confirming to IS 8112 and as per table 5 of BIS-456-2000 with minimum cement concrete of 380 Kg/M3 (Three hundred and Eighty kilogram) and Plinthd course aggregate using 20mm and 12mm gauge HBG stone jelly in the ratio of 70:30 (Seventy part of 20mm and thirty part of 12mm stone jelly) with maximum water cement ratio of 0.45 and using Superplasticizer 250 ml per 50Kg of cement but the rate excluding cost of steel reinforcement and form work etc. complete complying with standard specification. Labour Charges for Welding, cutting and Removal of Linear tube including cost of materials for cutting and welding as directed by the departmental officers to a hight of 1.25 mtr

Earthwork excavation for foundation (for narrow excavation) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. Refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete

Supplying and filling in foundation and basement with M - Sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Plain Cement concrete 1:4:8 (One cement four M sand and eight broken Machine crushed stone jelly) using HBG Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete

For column footing, Column pedestals, plinth beam, grade beams, staircase stpes, etc.,

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc

Brick work in following Cement Mortar using best quality of Second class ground moulded chamber burnt bricks 9"x4-3/8"x2-3/4" for foundation and basement including curing etc, complete complying with standard specification.

In Cement Mortar 1:5

For Foundation and Basement

Plastering the walls with Cement Mortar 1:5 - 12 mm thick using the M sand including curing and finishing neatly complying with standard specification and as directed by the departmental officers etc. complete.

Special ceiling plastering and finishing all RCC exposed surfaces such as RCC slabs, sunshades, canopies, stair case steps, landing slabs etc with CM 1:3 (One cement and three M sand) 10mm thick including hacking the surfaces and providing necessary CM nosing, beading as per size specified wherever necessary using the same mix etc., complete complying with standard specification and as directed by the Departmental Officer.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

For New Iron work Two coats including primer

Painting the walls with Two coats with first class quality Plastic Emulsion paint of approved colour over a priming coat including thorough scraping, clean removal of dirt. The rate includes cost of brushes, sand paper, plaster of parries, putty wherever required and neat finishing etc., complete complying with standard specification and as directed by the Departmental Officer (the colour and quality should be got approved by the Executive Engineer before use)

constuction of Rain water drainage chamber with 90 cm dia RCC ring with Cover Slab having 40mm thk 0.3m ht prefabricated RCC Ring Filling With 40 MM HB jelly at a depth of 1.50m including sinking of 6'' to 8'' borewell using hand bore set ,inset 8" pipe 20-feet including transportations.,labours charges .....,etc completed

Removing the flooring with cuddapah slab of size 50 mm thick including labour for Stacking etc., complete complying with standard specification and as directed by the Departmental Officer

Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam 250 mm thick specification including premixing the materials with water at OMC in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Paving the flooring with Old cuddapah slab of size 50 mm thick for flooring using CM 1:3 (one cement three M sand) including labour for fixing in position i etc., complete complying with standard specification and as directed by the Departmental Officer

Supply, Fbrication and fixing in position of frame work for fixing of plants in flower tunnel by using 6 mm ,8mm and 10mm RTC grills. The rate includes the cost of materials,transportation, labour charges and painting etc.,complete as directer by the departmental officers.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Finishing the Floor with Machine pressed Mangalore ornamental Tiles Hexagon type of size laid in cement mortar 1:3 20mm thick mixed with WPC at 2% by weight of cement used and top pointed with the same red oxide mixed mortar etc complete., complying with standard specifications

White washing one coat with freshly burnt white shell lime in all floors including cost of lime, blue powder, fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers.

For Two coat -100 m2

Supplying and fixing AC sheet roofing with 6mm thick asbestos cement sheets of fully corrugated (grey colour) of approved quality by drilling holes (and not by punching) with necessary ‘J’ / ‘U’ bolts and nuts of 8mm dia of suitable length and providing one set of bitumen washers of 25mm dia and 1.60mm thick for each bolt including protruding portion of bolts in roof shall be covered with bitumen compound etc., complete complying with standard specification and as directed.

Fabricating and supplying and erecting the required number of trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessary bolts nuts anchor bolt of approved quality hoisitn aligning and glazing the trusses inposition as per plan. The rate should include the cost painting the members with one coat of red oxide primer and zinc chromate etc., complete complying with standard specification and an directed bya the departmental officers.

Plain Cement concrete 1:2:4 (One cement Two M sand and four broken Machine crushed stone jelly) using HBG Machine crushed stone jelly of size 20mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete

Brick partition wall in CM 1:3 (One of cement and three of M sand) 11.50CM thickness using IInd class chamber burned bricks of size 9”x 4 3/8”x2 3/4” and using hoop iron with reinforcement if found necessary etc.., complete

Foundation and Basement

Supplying and fixing solid Blocks of following size confirming to SS 2145-1965 ( including jam blocks closures etc.,) made in CC 1:3:6 in CM 1:4 ( One of cement and four of M sand ) and partion wall including curing neat finishing etc., complete complying with standard specification and as directed by the departmental officers etc.,

Paving the flooring with cuddapah slab of size 50 mm thick both side machine polished edge and machine polished cutting for flooring using CM 1:3 (one cement three M sand) including labour for fixing in position i etc., complete complying with standard specification and as directed by the Departmental Officer

Cuddapah slab 38 to 40 mm thick

Manufacturing, supplying and fixing Precast Reinforced Cement concrete slabs of following thickness in RCC 1:2:4 (One cement, two sand and four aggregates) using following 10-12mm HBGs jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

50mm thick slab (using 20mm HBGs jelly)

Supplying and fixing in position of "L" angle of size 50x50x 6 mm for vertical post and supporting posts for fixing and tying the barbed wire as per standard specification and as directed by the departmental officers.

Supplying and fixing in position of Chain link (Fencing - TATA Brand or Equivalent)of size 2"x2" using 10 guage binding wire and tying with 2.5 mm GI wire at 0.50m vertical interval from base level (3 lines for 1.50m height) to the entire length of fencing with suitable RCC 1:2:4 or L Angle Post at centre to centre and to centre inserted with 2.5 mm GI Barbed wire (5 lines) at a vertical spacing of 0.30 m centre to centre to the entire length of fencing and further tigntened with 10 gauge binding wire etc., complete complying with standard specification. (Including barbed wire 5 lines - 0.30m c/c and excluding cost of RCC Post)

Supplying and laying of Galvolume sheet 0.5 mm thick of approved quality for roofing with necessary U or J bolts and unts bitumen GI washers etc., complete complying with standard specification.

constuction of Rain water drainage chamber with 90 cm dia 3Nos of RCC ring having 40mm thk each 0.3m ht prefabricated RCC Ring Filling With 40 MM HB jelly at a depth of 0.60m The Rate including Loading, Unloading,Transportations.,labours charges .....,etc completed

Providing and Fixing of polyurethane foam for Sloped roofas thermal insulation panels or Sandwich insulated panels with external 0.50mm total coated thickness pre painted Galvalume sheet with trapezoidal roofing profile having crest height of 38mm at every 333mm span , whereas internal 0.50mm total coated thickness pre painted galvanized iron sheet with micro ribbed profile and the insulation material will be chlorofluoro carbon and hydro chlorofluoro carbon free , high performance rigid polyurethane foam (PUF) conforming to IS 12436 having density not less than 40±2Kg/M3, Thermal conductivity (K-Value) 0.024 W/m.K measured at 10 degree C mean temperature along with necessary flashings such as L flashing, C flashing etc& accessories such as screws ,fastners ,sealants etc for fixing the panel etc., complete complying with standard specification.

Supply and fixing in position best quality PVC Soil/ waste pipes of various size having ISI mark and providing leak proof joints including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever necessary and making good the dismantled portion to the original condition, complying with standard specification etc., complete. - Below Ground Level

12V pixel Serial warm white 7days rent

LED 200W focus light warm white 7days rent

50W Spot light 7 Days rent

50W Spot light 3 Days rent

200W focus Light warm white 3 Days rent

thoranam serial light (3 Days rent)

5V RGB Pixel serial light(3 Days rent)

12V pixel Serial (orange,white) (3days rent)

100W focus Light warm white (3days rent)

Labours charges for fixing light Arrangments for rent inculding cost of labour for fixing , transport .,complete complying with standard specification and as directed by the departmental officers etc.,

Red carpet (40nos) ,shamiyana tent (5nos) ,chairs (100 nos),table(40nos) Arrangment for rent inculding cost of labour for fixing transport .,complete complying with standard specification and as directed by the departmental officers etc.,

Renovation of lilly pond with water proofing treatment near cafe ,lotus pond water proofing treatmentSize of(4.50mx2.50mx1.65m)near zipline,jet fountain with water proofing treatment ,landing tower near water fountain water proofing treatment Size of (4.20m dia x1.10m H),museum front pond water proofing treatment Size of(2.50m diax0.75m height), inculding cost of labour,material, transport etc.,complete complying with standard specification and as directed by the departmental officers etc.,

Supplying and fixing of Gallery Chairs.,complete complying with standard specification and as directed by the departmental officers etc.,

Supplying and fixing of Fixing additional SS support for chair ,Ms plate for fixing chair .,complete complying with standard specification and as directed by the departmental officers etc.,

Supplying of handicapped wheel chair .,complete complying with standard specification and as directed by the departmental officers etc.,

Re Painting the walls with Two coats with first class quality Plastic Emulsion paint ( Exterior) of approved colour over a priming coat including thorough scraping, clean removal of dirt. The rate includes cost of brushes, sand paper, plaster of parries, putty wherever required and neat finishing etc., complete complying with standard specification and as directed by the Departmental Officer (the colour and quality should be got approved by the Executive Engineer before use)

Two Way Blb Cock with Health Faucet

Removing and fixing of New 10 Lit cap PVC low level flushing tank for IWC or EWC coset Parryware

Supplying and fixing in position 15 mm dia Brass Chromium Plated Screw down tap (Heavy type) / Pillar tap / Stop Cock of approved make conforming to IS specification and quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete complying with standard specification and as directed by the Departmental officers. (Taps should be got approved by the Executive Engineer before use on the works)

Swan Neck Tap

GST at 18 percentage

SRE MCM & CO (BID ID -1219042)

PHOENIX & CO (BID ID -1219560)