Special repair of House No. 26 on Minar road Karnal

Amount

Dismantling brick work, tile masonry or tile lining and tile terracing . (b) in cement,[HSR 8.5(b)]

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled:- (HSR 8.18) a) Doors

(b) window

Scrapping white wash and colour wash[HSR 8.32(a)]

Scraping of cement plaster(HSR 8.32( c)

Dismantling white or coloured glazed tiles (to be carefully removed) [HSR 8.38]

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. [HSR 10.38]

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level ( HSR 11.9)

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg. per sqm on top of RCC the slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

Precast chequered tiles of 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement course sand mortar 1:3 with neat cement slurry between joints and over the base in floors , treads of steps and landings [HSR 14.45+ Note

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSON. (HSR 14.89)

Providing and fixing ceramic tiles / anti skid tile of size 400 mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, RAK & JOHNSON. (HSR 14.91)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) b) Size of ceramic Glazed tiles 300 x 450 mm

Providing & laying Baroda Green marble stone 17mm or above thick flooring including Matching the grains of marble slab in any patterns as specified over 12mm thick cement sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marble i.e. rubbig & polishing. The rates are for all height / story. The sample shall be got approved from EIC (HSR - 14.99)

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

15mm thick cement plaster 1:4 on the rough side of single or half brick wall. (HSR 15.10)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Painting two coats with synthetic enamel paint in all shades on old wood-work or metalic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25).

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58).

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Cost of aluminium fittings complete for doors and windows such as tower bolts, handles etc. and screws for these fittings (excluding sliding bolts) [HSR 17.72]. a) for single leaf shutter

Supplying and fixing hydraulic door closer,I.S.I. Mark, with necessary screws etc. complete (c) I.S.I. Designation No. III (size of door 851 mm to 1000 mm) [HSR 17.82(c)]

Providing and fixing sliding bolt with nuts and screws, etc., complete (b) Aluminium [HSR 17.83(b)] 300 mm x 16 mm.

250 mm x 16 mm

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc.,(non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (execluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) [HSR 17.90 (b)(-)Note (i) under item No. 17.18] ii) 35 mm thick.

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollocks, champ, chikrassy and chaplash, etc., (non-coniferous timber other teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chocks/cleats,stops, nails etc., complete fixed in position (execluding the cost of any fittings, other than specified above but including labour for fixing the same in position) [HSR 17.92 (-)Note (i) under item No. 17.18] ii) 35 mm thick.

Wrought iron and mild steel(using angles, flats ,square bars , tee and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) b) Door and window frame of size 76 mm x 38 mm with 35 mm wide single rebate

(d) door and window frame of size 114 mm x 50 mm with 35 mm wide double rebate

Providing and fixing in position best indian make (as approved by the Engineer-in-Charge) European type water closet suit with non-concealed 'P' or 'S' trap with or without vent and all other necessary fittings as fully described in item no. 30.3 above [HSR 30.4 (i)] White

Extra over item Nos. 30.1 to 30.4 and 30.6 for providing and fixing 15 litres capacity low level vitreous china ware cistern complete with flush bend all other necessary fittings instead of C.I. High level cistern complete with fittings. [HSR 30.12 (i)] White

Extra over item Nos. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. [HSR 30.13 (i)] White plastic seat (Solid)

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass chain and rubber plug, 15mm C.P. brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-Charge). All fittings best Indian make and; to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] white (iv) Size 550mm x 400mm with one no. tap.

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in item No.30.51 above [HSR 30.53] (a) size 600mm x 450mm x 200mm

Providing and fixing in position best Indian make shower with 15 or 20 i/d in-let. [HSR 30.66] c) C.P. brass with revoiving joint

Providing and fixing in position best Indian make Towel rails fixed in with rawl plugs embedded in walls with C.P. brass screws. Complete in all respect including cutting and making good the walls etc. [HSR 30.68] d) C.P. brass two swivel towel rail 400 mm long

Providing and fixing in position glass shelf fixed in with rawal plugs with C.P. brass screws complete including cutting and making goods the walls etc. [HSR 30.69] With C.P. brass brackets and guard rail (i) 600 mm x 125 mm

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc. [HSR 30.70] a) C.P. Brass (i) Soap dish large

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) complete including cutting and making good the walls etc. [HSR 30.71] a) Indian make (i) 600 x 450mm

Providing and fixing in position 15mm i/d C.P.brass & bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] a) Bib cock long body

c) Bib Cock

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). [HSR 30.76] 15mm stop cock (b) Concealed stop cock with flange

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) [HSR 30.78] b) Two way

Providing and fixing in position best Indian make flexible tube connection [HSR 30.82 a (iii)] a) Aluminium (iii) 15 mm x 450 mm

Providing and fixing in position automatic brass ball valves in tanks [HSR 30.110] WITH PEASTIC BALL (ii) 20mm i/d

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K., Supreme make with covers / lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with sutiable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (except civil work). (HSR 30.119) 1000 Ltr. capacity.

500 Ltr. Capacity

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. Including cost of Special. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (NS) a) 15 mm internal diameter of pipeline

20 mm internal diameter of pipeline

Recovery items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Dismantiling of bricks and Removing of Door and windos in the DNIT. In case it is not possible to use this material on the work, the agency can take away this material after approval from employer. This material will be issued at the price quoted by the agency. However the reserve price is as under:- i) Doors @ 800/- Each

ii) Windows @ 500/- Each

iii) Good Tiles @ 5/- Each

iv) Brick Bats @ 450/- cum

v) Iron Gate @ 3500/- Each Note:- All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

Ayush Enterprises

Sh. Raj Kumar

rameher contractor

Raj Laxmi Construction Co