SPECIAL REPAIR TO SMQs AT 1 WING AF SRINAGAR

Amount

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 sqm each complete all as specified and directed. Note: The damaged portion of the tiles/rendering shall be made good with the same material to match with the adjacent surface.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n exc 4 Sqm each and credited to the contractor all as specified and directed. Note: The damaged portion of the tiles/rendering shall be made good with the same material to match with the adjacent surface.

Supply and fixing for pressed steel frames for doors made out of mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crushed stone aggregate for filling back of chowkats complete all as specified and as directed.

Supply and fixing for Glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc, (without rash bars) divided into squares, with plain, chamfered or rounded, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); in second class hardwood, Complete all as specified and directed.

Supply and fixing for Plain, framed, panelled shutters (any number of panels), 35mm thick with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, suppled and fixed to chowkats in second class hardwood, Complete all as specified and directed.

Supply and fixing for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixing in opening Complete all as specified and directed.

Supply and fixing for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel heaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for tip rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointing together with solvent cement, supplying & fixing in the frame at site complete all as specified & directed.

Supply and fixing for factory made PVC cupboard shutter flush type 22 mm thick consisting of panel of hollow PVC profile section of 12 mm thickness consisting of M S frame made out of MS tubes of 19 gauge thickness and size of 12 mm x 12 mm inserted all around the hollow profile section and inserting one 12 mm x 12 mm MS tube in the centre of this section and lipped with 10 mm (5 mm x 2) thick and 12 mm wide on stiles and rails using solvent cement the inner panel shall be laminated with 5 mm thick termite proof, water proof and fire retardant printed PVC sheet using solvent cement on both the sides of the panel. The front side of the panel visible in the front of the cupboard to be edge bonded using 20 mm x 1 mm thick PVC leaping on both the edges with locking arrangements of both panel etc complete all as specified and as directed.

Supply and fixing for factory made PVC shelf 22mm thick consisting of panel of hollow PVC profile of 12mm thickness consisting of M S frame made out of M S tubes of 19 gauge thickness and size of 12mmx12mm inserted all around the hollow profile section and insert one 12mmx12mm M S tube in the center of this section and lipped with 10mm(5mmx2)th and 12mm wide on stiles and rails using solvent cement.The inner panel shall be laminated with 5mm th termite proof water proof and fire retardent plan PVC sheet using solvent cement on both the sides of panel.The front side of the partition visible in the front of the cupboard to be edge bonded using 20mmx1mm thick plain PVC Leaping on both edges etc. complete all as specified and as directed.

Supply and fixing for Aluminium alloy, anodised, sliding door bolt 300mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

Supply and fixing for 150 mm long Aluminium anodised,handle of extruded section fabricated type anodised and fixed complete all as specified and directed.

Supply and fixing for Aluminium, anodised, barrel tower bolts 150mm size of extruded section, complete all as specified and directed.

Supply and fixing 125 mm long Aluminium anodised,handle of extruded section fabricated type anodised and fixed complete all as specified and directed.

Supply and fixing Aluminium, anodised, barrel tower bolts 125mm size of extruded section, complete all as specified and directed.

Supply and fixing mild steel Butt hinges 100mm size, medium weight, cold rolled, complete all as specified and directed.

Supply and fixing mild steel Butt hinges 75mm Size, medium weight, cold rolled , complete all as specified and directed.

Floor door stopper of aluminium alloy body and tounge, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140mm, complete all as specified and as directed.

Supply and fixing door strip comprising of aluminium holds & rubber strip fixed at bottom of door shutter with screws complete all as specified and as directed.

Supply and fixing sheet glass 3mm thick, ordinary quality and glazing with oil putty/wooden beads in square or rectangular in section n exc 0.5 sq.m in each pane complete all as specified and directed.

Material and Labour for galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tack or galvanised wire staples or fixed with nails and wooden beads, complete all as specified and directed.

Supply and fixing Figured Glass pin head type 4mm thick n exc 0.5 Sqm and glazing with oil putty, Complete all as specified and directed.

Supply and fixing factory made steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm including grill of 8mm square bars, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. ecomplete all as specified and as directed.

All as per Srl item No 22 above but steel ventilators top/side hung.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Material and Labour for Providing and fixing GI powder coated frame work for Gypsum board ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylone sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with clips of 10.5mm fixed to the intermediate channel at 457mm centre to centre, fixed in repairs, complete all as specified and directed.

Material and Labour for Non asbestos fibre cement building board Size 590x590x6mm thick fixed or laid/inserted to timber/GI/Aluminium framework with screws to ceiling flat or sloping complete all as specified and directed.

Material and Labour for preparation of new or previouly untreated plaster/ AC sheet surfaces of ceiling including cornices and applying two coats of oil bound distemper colour/tint complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Supply and fixing 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws., complete all as specified and directed.

All as per ser item No 29 here-in-above but except sheeting.

Supply and fixing 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Material & Labour for preparation of new or previously untreated steel and iron surfaces and applying two coats of synthetic enamel paint of any description over 10cm width or girth over a coat of red oxide primer complete all as specified and directed.

Supply and fixing mild Steel ordinary rat tail rod pattern springs including roller and roller plate 300mm length, complete all as specified and directed.

Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for, Complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finished surface; not exceeding 200m thick (Horizontal or sloping), complete all as specified and directed.

Material and Labour for RCC, Type B1 1:2:4 (20 mm graded aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material and Labour for MS TMT bars 6mm to 8mm dia, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed

Supply and fixing Hasp & Staple, 125 size, safety type aluminium anodised with mild steel hinge pin including bolt, to hinge plate and fixed with screws, complete all as specified and directed.

Supply and fixing in repair drapery rod 25mm dia fency type mild steel plastic coated inculding wooden funnel and wooden brackets, Complete all as specified and directed.

Material and Labour for preparation of new or previously untreated wood and wood based surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors aprons etc laid in cement mortar of any thicknes, complete all as specified and directed.

Material and Labour for granite (of any type) work (table rubbed and polished) 20mm thick as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking , sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3 kg of cement per sqm complete all as specified and directed.

Material and Labour for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface including 20 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM 1:6 complete all as specified and directed.

Material and Labour for Coloured Glazed ceramic tiles in vertical surface 450X300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the existing surface including Rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as backing coat, complete all as specified and directed.

Material and Labour for machine cut kota stone slab flooring 20-25 mm thick over screed bed or bedding layer 20 mm thick in CM 1:6, and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing & polishing complete all as specified and directed.

Material and Labour for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with plgment to match the shade of the slab, rubbing and polishing including backing coat 10mm thick in CM 1:4 , complete all as specified and directed.

Demolition of plain cement concrete in ground floors and pavings not exceeding 15 cm thickness, Complete all as specified and directed.

Material and Labour for 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in hard standing/pavings/plinth protections, finished even and smooth without using extra cement, Complete all as specified and directed.

Material and Labour for Machine pressed, glossy finished 25 mm thick coloured cement concrete chequered tiles of size 300mm x 300 mm of pattern as approved set jointed and pointed in neat cement slurry in floors complete all as specified and directed

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. Complete all as specified and directed.

Material and Labour for brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, Complete all as specified and directed.

All as per ser item No 53 here-in-above but except bricks

Material and Labour for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 Complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Material and Labour for Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement complete all as specified and directed.

Material and Labour for Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement complete all as specified and directed.

Material and Labour for rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement, complete all as specified and directed.

Material and Labour for preparing new plastered surfaces and applying two coats of distemper oil emulsion including Thin layer of wall care putty and priming coat preparatory to distempering on surfaces of wall, complete all as specified and directed.

Material and Labour for preparing of new surface of plaster and applying three coats of white wash on ceiling, complete all as specified and directed.

Material and Labour for Preparing of new surface of wall and applying two coats of snowcem over one coat of primer,complete all as specified and directed.

Taking up or down steel water tubing 15mm bore and connections, including cleaning or re-fixing for removal to store complete all as specified and directed.

Supply and fixing GI tubes 15 mm bore 'medium grade' with all fittings and fixed complete to walls and ceilings or laid in trenches complete all as specified and directed.

Taking up or down steel water tubing 20mm bore and connections including cleaning for re-fixing or removal to store complete all as specified and directed.

Supply and fixing for GI steel water tubing 20mm bore medium grade with all fittings and fixed to walls, ceiling or laid in floor complete all as specified and directed.

Material and Labour for Lagging to pipes 20mm bore used in external water supply or plumbing all around with 25mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25mm gauge 20mm mesh complete all as specified and directed.

Supply and fixing in repairs vitreous china wash hand basin white flat back, size 630x450 mm including brackets complete all as specified and directed .

Supply and fixing in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fixing in repair PVC waste pipe flexible for WHB of 32mm size complete all as specified and directed.

Supply and fixing in repair, Vitreous china squating pan, orissa pattern size 580 x 440mm and making good, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., including trap set in and including concrete Complete all as specified and directed.

Supply and fixing in repairs PVC valveless, syphonic action type, flushing cistern, low level 10 ltr capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply and fixing in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm Complete all as specified and directed.

Supply and fixing in repair, Kitchen plate rack made of stainless steel 1 mm thick with plugs washers as overall size of 75cm x 75 cm including fixing to wall and all accessories Complete all as specified and directed.

Supply and fixing in repairs 15 mm bib tap chromium plated, cast copper alloy with capstain head screwed down screwed for iron pipe or for brass ferrule fancy type, complete all as specified and directed.

Supply and fixing in repairs chromium plated angle/stop valve of cast copper alloy screwed down high pressure with capstain head screwed both ends for iron pipe or for unions and fixed 15 mm bore complete all as specified and directed . Make: Cera/Prayag/Jaquar

Supply and fixing in repairs chromium plated shower roses with CP Arms, 15mm bore, complete all as specified and directed. Make: Cera/Prayag/Jaquar

Shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic Cleats complete all as specified and directed (minimum weight300gms)

Supply and fixing in repairs brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges completed all as specified and directed.

Supply and fixing in repairs concealed stop cock fancy type chromium plated with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed.

Supply and fixing in repairs 15mm dia Brass chromium plated wall mixer for mixing hot & cold water fixed in repairs, complete all as specified and directed.

Supply and fixing in repair 15mm dia Brass chromium plated Sink mixer (wall mounted) for mixing hot & cold water complete all as specified and directed.

Supply and fixing in repair 15mm dia Brass chromium plated central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water, complete all as specified and directed.

Supply and fixing in repairs Soap dish, brass chromium plated any type, fixed to plugs with chromium plated brass screws Complete all as specified and directed.

Supply and fixing in repairs, PVC (SWR) pipes 75mm dia single socketed, in any length with rubber ring joints laid in trenches, floors or fixed to wall, complete all as specified and directed.

Supply and fixing in repairs, PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints laid in trenches, floors or fixed to wall complete all as specified and directed.

Supply and fixing in repairs 75mm bore dia PVC floor trap(SWR) plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed .

Supply and fixing in repairs 75mm bore PVC(SWR) bends any radius complete all as specified and directed.

Supply and fixing in repairs 75mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

Supply and fixing in repairs 110 mm bore PVC(SWR) bends any radius provided with access door complete all as specified and directed.

Supply and fixing in repairs 110mm bore PVC (SWR) junction single (Single T) equal or unequal with access door complete all as specified and directed.

Supply and fixing in repairs 125/110mm bore PVC (SWR) 'P’ trap complete all as specified and directed.

Material and Labour for complete removal of existing treatment of walls and applying thin layer of wall care putty and preparing the smooth surface with sand paper and applying two coats of distemper oil emulsion (OBD) paint on walls complete all as specified and directed.

Material and Labour for preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying one coat of white (lime) wash complete all as specified and directed .

Supply and fixing 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks and removing from site including 20 mm Ball brass valves, high pressure, with polythene float and flynut complete all as specified and directed .

Material and Labour for preparation of old painted steel surfaces of any description and applying one coat of synthetic enamel paint including preparation of old painted steel and iron surfaces of any description exc 10cm width or girth complete all as specified and directed.

Complete removal of existing treatment from brick walls or concrete surfaces including scraping down smoke soots, moulds, moss and trading oil and greasy spots etc including cornices, pilasters etc (Plastered or un plastered surfaces) and applying two coat of cement based paint over a coat of cement primer including preparation of surfaces on walls complete all as specified and directed .

Dismantling timber scantling, 40 Sqcm and over in section in any position including rafters and purlins complete all as specified and directed .

Supply and fixing second Class hard wood as in scantling, wrought, timber framed and fixed complete all as specified and directed .

Taking down carefully copper/aluminium point wiring (light, fan, socket, bell or power) including all electrical fittings & fixtures(DBs, submain,cables etc) and making good disturbed surfaces of wall , floor etc and matching with original colour of wall, complete all as specified & directed.

Material and Labour for Point wiring with 1.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable 1100 volt grade in and including concealed/surface , non metalic rigid pvc medium grade ISI marked conduit not less than 19 mm with all fittings & other accessories and also including PVC insulated ISI marked unseathed FRLS cable 1100 volts grade of size 1.5 sq mm copper conductor as earth wire to common earth dolly including concealed in wall/ceiling, modular MS box with modular cover plate with frame suitable for modular switches, sockets, fan regulator etc for the following complete all as specified and directed :- Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

One light/fan point controlled by one way switch 6 amps 240 volts

One light point controlled by two way switch 6 amps 240 volts

One bell point controlled by one bell push switch 6 amps 240 volts

One 3 pin 6 Amps switch socket out let point on independent Board

One 3 pin 6 Amps switch socket out let point on same board

Material and Labour for Point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable 1100 volt grade in and including concealed/surface , non metalic rigid pvc medium grade ISI marked conduit not less than 19 mm with all fittings & other accessories and also including PVC insulated ISI marked unseathed FRLS cable 1100 volts grade of size 1.5 sq mm copper conductor as earth wire to common earth dolly including concealed in wall/ceiling, modular MS box with modular cover plate with frame suitable for modular switches, sockets 16 Amps, 240 volts complete all as specified and directed Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

Supply and fixing modular one way switch 6 Amp 240 volt marked light/fan suitable for one model etc complete as specified and directed.Make- Legrand/ Anchor/ Havells or equivalent .

Supply and fixing modular two way switch 6 Amp 240 volte suitable for one model etc complete as specified and directed. Make- Legrand/ Anchor/ Havells.

Supply and fixing Modular 6 Amp 5 pin universal socket suitable for two model , 250 volts complete all as specified and directed by Engr-in-charge Make- Legrand/ Anchor/ Havells.

Supply and fixing modular switch one way 16 Amps 240 volts suitable for one model complete all as specified and directed Make- Legrand/ Anchor/ Havells .

Supply and fixing Modular 6/16 Amp socket suitable for two model , 250 volts complete all as specified and directed Make- Legrand/ Anchor/ Havells .

Supply and fixing modular bell push switch with indicator 6 Amp 240 volte suitable for one model etc complete as specified and directed Make- Legrand/ Anchor/ Havells

Material & Labour for for ceiling rose with three terminal as per relevant IS complete all as specified and directed Make SSK/havells/legrand /Anchor

Supply and fixing modular step type two model fan regulator suitable for 120 watt 250 volts complete as specified and directed Make- Legrand/ Anchor/ Havells.

Supply and fixing bell electric AC, 230V, Single phase, Dingdong type complete all as specified and directed.Make- Legrand/ Anchor/ Havells or equivalent.

Supply and fixing decorative Self ballasted LED Batten With Extruded Thermoplastic body with PC diffuser fitting with>120º wide Distribution 20 watt luminaire complete all as specified & directed .Make:- CG C&S ,Havells ,Crompton.

Supply and fixing Energy saving new generation 10 W LED IP 65 bulkhead luminaire with opal diffuser with 10 LED lamp complete as specified and directed .Make:- CG C&S ,Havells ,Crompton.

Supply and fixing mirror light sleek LED mirror light provided with high output diffuser 10Watt with suitable capacity driver with all components as per manufacturer complete all as specified and directed .Make:- CG C&S ,Havells ,Crompton.

Supply and fixing surface mounted round type energy saving ceiling mounted decorative LED 8 watt luminair with opal diffuser for soft light with suitable driver etc complete all as specified and directed .Make:- CG C&S ,Havells ,Crompton.

Supply and fixing Decorative type lamp holder suitable for pin type LED 10 watt including lamp etc complete all as specified and directed .Make:- CG C&S ,Havells ,Crompton.

Disconnecting all water and electric connections of geysers and taking down carefully installed storage type electric geysers of any capacity of any make/type/size (horizontal/vertical) lowering and setting aside opening geysers examining and checking thoroughly for requisite repair/ replacement of defective/worn-out/ unserviceable components/parts materials including preparing inventory for each geyser separately in presence of Engineer-in-Charge and removing all scale and dirt de-scaling of deposited in inner copper tank and outer tank and heating elements by HCL or aqua clear pedilite solution, thermostat, indicator lamp, assemble checking electrical connection, stopping of minor leaking by soldering/brazing of the inner copper tank and replacement of defective worn out unserviceable components/parts and painting of geyser 25 ltrs after scraping, cleaning, knotting and stopping including preparation of surface of geyser and rubbing with ammery paper for painting with one coat of duco paint by spray painting mation to achieve glossy finish of approved make first quality and re write MES No. on the body of geyser with black synthetic enamel paint (letters and figures 2cm high ) & re-fixing geyser in its original location including hoisting, connecting to water & electric connection and testing for proper functioning of geysers including earthing to the entire satisfaction of the Engineer-in-Charge including the replacement of the following items etc complete all as specified & directed. (a) Supply only Fiber reinforced PVC nylon pipe heavy duty size 450 mm long 15mm bore with brass coupling chromium plated with rubber washers as both ends as per IS.-01 Nos (b) Supply only Flexible chromium plated connection pipe size 450 mm long 15 mm bore with brass chromium plates coupling suitable for geyser any capacity-01 Nos

Taking down carefully ceiling fan any type, sweep and make for overhauling including dismantling of blade frame and opening and examining motor cleaning of dust/dirt of fan cleaning and greasing of ball bearing and bushes with fresh oil and best quality of grease respectively and reassembling of complete fan after re-fixing parts in its original location and hanging connecting and testing ceiling fan for smooth functioning incl replacement of rubber real insulator,split pin,nut,bolt, washer, 3 core flexible cable from connector to ceiling rose, and painting with one coat of synthetic enamel paint with spray painting machine & marking MES No. with black paint complete all as specified and directed.

Material and Labour for epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 8 way SPN suitable for MCB DB's 230 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush mounting complete all as specified and directed.

Supply and fixing epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 4 way TPN suitable for MCB DB's 415 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed.

Supply and fixing MCB single pole ISI marked ISI Marked `C' series working on 240 Volts 50 HZ AC supply for incomming and out going controlling cercuit of capacity 6-32 Amp breaking capacity 10 KA etc all as specified and directed. Make Legrand/ Havels/Anchor.

Supply and fixing MCB single pole ISI marked ISI Marked `C' series working on 240 Volts 50 HZ AC supply for incoming and outgoing controlling circuit of capacity 40-63 Amp breaking capacity 10 KA etc complete as specified and directed.

Supply and fixing MCB single pole and neutral ISI marked `C' series working on 240 volts 50HZ AC supply for incoming & outgoing controlling system of capaicty 40-63 Amps 10 KA breaking capacity etc complete as specified and directed.

Supply and fixing MCB triple pole and neutral ISI marked `C' series working on 240 volts 50HZ AC supply for incoming & outgoing controlling system of capaicty 40-63 Amps 10 KA breaking capacity etc complete all as specified and directed.

Material and Labour for sub main wiring with two single core, PVC insulated,ISI marked, unsheathed, 1100 volts grade multistranded copper conductor FRLS cable drawn into and including suitable size non metalic rigid pvc conduit (ISI marked) concealed/surface with all accessories and including one single core pvc insulated multistranded unsheathed 1100 volts grade copper conductor FRLS cable as earth wire of the following size complete all as directed & specified.

(a ) 2x6.0 sqmm + 1x6.0 sqmm earth wire

Supply and fixing meter box made out of 1.6mm thick ms sheet of size 45x30x20cm with front opening & locking arrangement incl painting with two coat of synthetic enamelled paint over a coat of red oxide incl taking down serviceable energy meter from existing position and fixing in ms box incl suitable size hole for incomming and out going cable etc complete as specified and directed.

Material and Labour for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground (earth pit not less than 2.25 metre deep below ground level) vertically, with top edge of the plate not less than 1.25 mtr below normal ground level, connected to galvanized iron wire 4mm dia by means of nuts, bolts, washers of GI steel all as shown on electrical plate No 3 of MES Schedule Part I connected to earthing test point and testing on completion with and including necessary excavation and earth work, earth electrode, earthing lead from electrode to equipment/substation, adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded black trap/granite/Basalt stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm graded black trap/granite/Basalt stone aggregate) 40mm thick cover, reinforced with 6mm dia bars 3 Nos both way with 12mm dia round bar handle, GI light grade watering pipe 15 mm dia with funnel and wire mesh, and 40 mm dia GI light grade earth lead protection pipe , complete all as specified and directed. Note :- Earth strip and protection pipe upto test point i.e. upto 7.5 RM is included in the unit rate of this item. Contractor shall quote his rate accordingly.

M/S Abdul Ahad Rather

M/S Wani and Sons

M/S A.R.TANTARY

M/S maqsood enterprises

M/S MIR AND CO

M/S M.R. Construction

M/S MUBASHIR SHABIR WANI

M/S RATHER CONSTRUCTION CO