SPECIAL REPAIR TO BLDG NO P-197 (01 TO 04), P-476 AND BLDG NO P-641 AT SRI GANGANAGAR MIL STN

Amount

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames) complete all as specified and directed by Engr-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)

All as per item No. 03 above but size of frame/chowkhats 65X 100 mm complete all as specified and directed by Engr-in-Charge.

All as per item No. 03 above but size of frame/chowkhats 45X 70 mm complete all as specified and directed by Engr-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type skelton/Gauzed door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including stainless steel 304 grade (natural finish) wire cloth. complete all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf

S&F Aluminium Haydraulic door closer springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

S&F powder coated aluminium grill of approved design/pattern with aperture size 50mm dia 3-4mm fixed to aluminium window with all necessary fixing arrangement of size 50mmx5mm thick complete all as specified and directed by Engineer-In-Charge.

S & F framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290 – Gde – 165 complete all as specified and directed by Engineer - in - Charge.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified and directed by Engr-in-Charge.

S&F in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified and directed by Engr-in-Charge.

M & L toughned glasss, figured glass ordinary quality 5 mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing and removing rubbish off the premises complete all as specified and directed by Engr-in-Charge.

M&L for double charged, vitrified, stain & scratch resistant, joint free, premium quality coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed adhesive of Sika (Ceram Grey) @ 5 Kg/sq.m and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-Charge.

M&L for double charged, vitrified, stain & scratch resistant, joint free, premium quality coloured tiles 600 X 100 mm and 9-10 mm thick in any pattern of light & dark tiles as approved,on vertical surfaces such as in skirting/dado etc ,length of each unit not less than 600 mm and height not more than 150mm, set and jointed adhesive of Sika (Ceram Grey) @ 5 Kg/sq.m over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-Charge. Note : Skirting should be flushed with the wall plastering.

M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-Charge. Note : Dado should be flushed with the wall plastering.

M&L for anti-skid ceramic joint free premium quality coloured tiles 300 X 300 mm and 6-7 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-Charge.

Dismantling stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed by Engr-in-Charge.

M&L for 18 to 20 mm thick Granite (of any type) slab of approved shade as in kitchen platform,steps,jambs,pillars,window cills,cooking plateforms etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 25mm thick screed bed (bedding layer) in CM 1:4, complete all as specified and directed by Engr-in-Charge.

M&L, Machine cut kota stone slab flooring, cills 18-20mm thick over cement screed base laid and jointed With grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

M&L, Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engr-in-Charge.

Water proofing treatment to sunken slab and adjjoining vertical surfaces as specified under :- (a) M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compound trowel even and smooth with steel trowel on sunken surfaces (Note : only Plan area should be meassured for payment WPC shall be measured and paid separately) (b) Applying first coat of chemical pidifin 2K(Dr Fixit) on cleared RCC surfaces @ 0.86 Kg/Sqm (Minimum) as recommended by manufacturer. (c) Provide a layer glass fibre mesh of size 2.25mm x2.25mm (45 GSM) over first coat of chemical Pidifin 2K as per manufacturers recommendation. (d) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25mm x 2.25mm (45 GSM) as recommended by manufacturers.

Supply only Integral water proofing compound ISI marked confirming to IS 2645 - 2003 complete all as specified and directed by Engr-in-Charge..

M&L for PCC 1:5:10, type E-2 as in filling of sunken floors etc. complete all as specified and directed by Engr-in-Charge.

M&L 40 mm GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as specified and directed by Engr-in-Charge.

Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, complete all as specified and directed by Engr-in-Charge.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, complete all as specified and directed by Engr-in-Charge.

M&L for applying Pitch free PU based Liquid applied single component elastomeric seamless, water and vapour membrane system for concrete @ 2.50 Kg/M2 (02 Coats). Typical application will include roofs, podium, balconies, floor slabs, suspended floors, patios, bathrooms, inspection pits, swimming pool, bridge decks, Conforming Tensile Strength (2N/mm2) (ASTM D412)/Tear resistance (15 KN/m) (ASTM D624-00) and Crack bridging (ASTM C 836/ASTM c 1305 modified) 2mm. After 72 hours of curing, flood test can be carried out to a minimum depth of 50 mm of water for 24 hours. Drains shall be plugged and barriers placed to contain the water. Make : Equivalent of Fosroc/Sika/Bostik/Choksey etc Note :- (i) All above operations to be done by auth application in order all as specified and directed. Note: Auth company will submit confirmation of their Auth Applicator before execution of work.

M&L for cement concerete type C2 1:3:6 (40mm graded aggrigate) as in filling and mass concerete etc complete all as specified and dirceted by Engineer-In-Charge.

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 8-10 mm) with SRI (solar refractive index) > 78, on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, complete all as specified and directed by engineer in charge

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge.

M & L for PCC (1:3:6) type C-2 (using 40mm graded agg) 75mm thick as in plinth protection complete all as specified and directed by Engr-in-Charge.

Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engr-in-Charge.

S&F CPVC ISI SDR 11 pipes 20 mm dia with all fitting, including all Brass Fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. In brick walls complete all as specified and directed by Engr-in-Charge..

Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engr-in-Charge.

S&F CPVC ISI SDR 11 pipes 25 mm dia with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 25 mm complete all as specified and directed by Engr-in-Charge.

Dismantling water tanks of any description exc 250 and n.exc 500 ltrs capacityand removal from site complete all as specified and directed by Engr-in-Charge.

Dismantling water tanks of any description 1000 ltrs capacity and removal from site complete all as specified and directed by Engr-in-Charge.

S&F 1000 ltrs capacity Rotational moulded polyethylene in white coloured three layered ISI Marked water storage tanks (cylindrical vertical with closed top) including 25 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe hoisted and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F 500 ltrs capacity Rotational moulded polyethylene in white coloured three layered ISI Marked water storage tanks (cylindrical vertical with closed top) including 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe hoisted and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F in repairs 25 mm bore cpvc gate valve with handle, screwed both ends for inlet & outlet pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F central hole wash basin mixer 15mm bore brass without polp up waste with 10mm dia 450mm long copper pipes. complete all as specified and directed by Engr-in-Charge.

S&F in repairs, Brass CP Kitchen Mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

S& F single lever High flow consisting of exposed part kit with operating lever , wall flange & button and concealed body ,cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure complete all as specified and directed by Engr-in-Charge. Make Cera:(exposed part F1020721, concealed part F4030101, bath Spout F1020661), Jaquar or equivalent in same Pattern

S&F in repairs 15mm bore Long body bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engr-in-Charge.

S&F CP angle valve for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type fixed as in repair complete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china premium/1st quality wash down water closet wall hung EWC white (closed pattern incl all necessary like rag bolts/gel gasket, PVC (SWR) WC connector benty type etc.) Plastic water closet soft slim seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device complete all as specified and directed by Engr-in-Charge.

S&F in repairs concealed cistern set with full frame compatible with wall hung type water closet complete all as specified and drected by engineer in charge.

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified and directed by Engr-in-Charge.

S&F stainless steel plate racks of size 900mm x 600mm x 250mm and thickness of SS strip of 1mm fixed on wall etc complete all as specified and directed by Engr-in-Charge.

S&F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe including 40mm dia CPBrass waste fitting amd waste pipe overall size of SS sink 495mm x 420mm bowl size 410mm x 330mm x 160mm, etc complete all as specified and directed by Engr-in-Charge.

S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and directed by Engr-in-Charge.

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store(measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.

Dismantling and disconnecting existing CI soil waste/vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed by Engr-in-Charge.

Dismantling and disconnecting of existing CI soil waste/vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps complete all as specified and directed by Engr-in-Charge.

S & F 75 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes as directed complete all as specified and directed by Engr-in-Charge.

M&L PVC (SWR) branch pieces, 110 mm bore, (equal or unqual), double (double Y) complete all as specified and directed by Engineer-in-Charge.

M&L PVC (SWR) 110 mm vent cowl complete all as specified and directed by Engineer-in-Charge.

S & F 75 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes as directed complete all as specified and directed by Engr-in-Charge.

M&L PVC (SWR) branch pieces, 75 mm bore, (equal or unqual), double (double Y) complete all as specified and directed by Engineer-in-Charge.

M&L PVC (SWR) 75 mm P Trap complete all as specified and directed by Engineer-in-Charge.

Cutting in to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for as specified dia of pipe 150mm complete all as specified and directed by Engr-in-Charge.

M &L for providing Modular Kitchen Cabinet/cup board with shutters in required sizes & shape at site made out of 18 mm thick one side decorative laminate and other side balancing lamination sheet consisting of carcass 18 mm thick PVC sheet & PVC sheet with all required brackets SS screws e.t.c. The panels shall be fabricated using adhesive and screws where ever required . All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per manufacturer instructions and as directed by Engineer-in-Charge.

Supply & fixing Factory made prefabricated Pressed steel Door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary MS rawl plug/bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm (Make Godrej/Harison/Navtal) including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not -visible from front) and hammer tone paint on exterior surface ( visible from front) as per Godrej Pattern complete all as specified and as directed by Engineer-in-charge.

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:4 (10mm thick rendering in first layer and 5 mm thick rendering in second layer)on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for prepration of New plastered Internal wall surface complete applying the following :- (a) M&L wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of interior acrylic emulsion over a coat of chalk whitening priming by using Airless spray / Roller over complete all as specified . Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible .

M&L for prepration of New external plastered wall surface complete all as specified complete all as specified and applyingthe following :- (a) Applying wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) two coat of exterior acylic emulsion by using Airless spray / Roller over and incl a coat of acrylic emulsion external primer complete all as specified . Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of where using of Mechanical equiment are not posiible.

M&L for prepration of New plastered ceiling surface complete applying the following :- (a) M&L wall care putty in two coats on ceiling surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of interior acrylic emulsion over a coat of chalk whitening priming by using Airless spray / Roller over complete all as specified .

M&L for complete removal of existing treatment including filling depression of scraped surface with wall care putty in two coats on old internal wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as specified and directed complete and applying two coat of interior acrylic emulsion of approved tint over a coat of primer on old prepared surface by using Airless spray / Roller over complete all as specified & directed. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible .

M&L for complete removal of existing treatment including filling depression of scraped surface with wall care putty in two coats on oldceiling surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as specified and directed complete and applying two coat of interior acrylic emulsion of approved tint over a coat of primer on old prepared surface by using Airless spray / Roller over complete all as specified & directed.

M&L for complete removal of existing treatment including filling depression of scraped surface with wall putty two coats 1.5 mm thick each on Old external wall surfaces of any desciption , prepratio of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology , complete all as specified and applying the following :- (a) M&L two coats of exterior acylic emulsion by using Airless spray / Roller over and incl a coat of acrylic emulsion external primer complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of where using of Mechanical equiment are not posiible

M&L for Obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work etc complete all as specified and directed by Engineer - in - Charge.

M&L for Writing letters or figures with fluorecent paint ( Block. Roman, Italic or Indian) n exc. 30 cm high etc complete all as specified and directed by Engineer - in - Charge.

Dismantling of brickwork built in cement mortar of any description complete all as specified and directed as per Engineer-In-Charge

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

M&L for welding in repairs Thickness of metal to be welded will be Exc 9 mm but not exc 20mm complete all as specified and directed by Engineer - in - Charge.

Demolition of RCC of any description such as Kitchen chimney, chajja, shelves, OHT Tanks. etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition)

M&L for reinforced cement concrete (nominal mix) type B1 1:2:4 (20 mm graded stone aggregate) as in Slab supported on walls for tank staging and in shelves and etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-charge

M&L for reinforced cement concrete type M-25(20 mm graded stone aggregate) Design mix as in Slab supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-charge

M & L RCC M-25 (20mm graded stone aggregate) design mix as in beams,cantileavers,bressummers,lintel over 1.50m span complete all as specified and directed by Engineer-in-charge

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

Use and waste of form work torough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick complete all as specified and directed by Engr-in-Charge.

Use and waste of form work torough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick complete all as specified and directed by Engr-in-Charge.

Formwork to sides and soffits of lintels & beams including supports, overhangs, etc. with rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.

Formwork to chajjas, troughs and similar items including edges for rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.

S&F vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including all accessories as recommended by manufacturer and incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size complete all as specified and directed by Engr-in-Charge.

M&L for Machine pressed Precast cement concrete interlocking coloured ( glossy finished / ruberised paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with and including 40mm thick sand cushining complete all as specified and directed by Engr-in-charge.

M&L providing and fixing precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in Kerb Stone of any section indicated with plain fair faces including chamfers weatherings throughting etc and setting in CM (1:4) complete with joints to match all as specified and directed by Engineer-in-Charge.

M & L 75mm thick Cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed by Engr-in-Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm laid in floor set and jointed in cement slurry including 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish even & fair and pointed in epoxy grout mixed with pigment to match the shade of tiles complete all as specified and directed.

M&L for 25 thick cement concrete flooring type B-0 1:2:4 (12.5 mm graded stone aggregate) complete all as specified and directed.

M&L for PCC 1:2:4 type B2(20 mm graded aggregate) as in roof padding/roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engineer in chgarge.

S & F of Fiber Glass Reinforced plastic (FRP) Door Frames of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Doorframe laminate shall be 2 mm thick and shall be filled with suitable wooden black in all the three legs. The frame shall be covered with fiberglass from all sides MS stay shall be provided at the bottom to steady the frame.complete all as specified and directed by Engineer - in - Charge.

S & F of 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required color and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F Aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge

S&F Aluminium window and ventilator shutters, side hung type without sash bar, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, powder coated aluminium snap beading screws, powder coated aluminium fitting such as hinges type B-21 100 mm size (2 Nos), suitable handle (2 Nos) of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 125x60mm complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 105x60mm complete all as specified and directed by Engineer - in - Charge.

M&L Cement concrete 1:2:4 type B–0(12.5 mm graded stone aggregate) filling of pressed steel frame and hold fast blocks etc complete all as specified and directed by Engineer - in - Charge.

M & L for applying two coats of synthetic enamel paint (ordinary tint) over one coat of red oxide primer on new steel surface over 10 cm width or girth, not otherwise described including preparation of surface complete all as specified and directed by Engineer - in - Charge.

S & F for 35mm thick factory made gauged skelton shutters open rebated and prepared to receive gauze etc edges of framing plain, chamfered or rounded fitted with cut and mitred beady for receiving gauze etc of 35mm thick and door for Iind class hard wood rail and style as specified in SSR Part-I Section 8, cluase 8.24(a) and all as specified and directed by Engr-in-Charge.

S & F for 35mm thick factory made IInd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

M&L for preparation of surfaces of new wooden Surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F 100 mm Butt hinges stainless steel with galvanised mild steel hinge pin and fixed type C-21 all as specified and directecd by Engr-in-charge.

S& F aluminium anodised barrel tower bolts of extruded section and fixed 150 mm size complete all as specified & directed by Engineer in charge.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed by Engineer in charge.

S & F aluminium handles D type with back plate, anodised, 150mm long complete all as specified and directed by Engineer - in - Charge.

S&F 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-charge.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor and overall length of cover plate 140 mm complete all as specified and directed by Engineer in charge.

S&F in repair 15 mm dia chromium plated concealed type stop valves, cast copper aloy with crutch or butterfly handles screwed down high pressure, screwed both ends for iron and fixed.

S&F in repairs, Angle valves, chromium plated cast screwed down, high pressure copper alloy, with crutch or butterfly handles, screwed both ends for but fancy type 15mm bore iron pipe or complete all as specified and directed by Engineer - in - Charge.

S&F in repairs SS soap dish of any size fixed with screws complete all as specified and directed by Engineer in charge.

S&F in repairs grating doom 100 mm dia of stailess steel with and without hole complete all as specified and directed by Engineer vin charge.

S & F in repair stainless steel tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.

S & F in repair stainless steel towel ring min 30mm dia including brackets complete all as specified and directed by Engineer - in - Charge.

S&F in repairs fancy type long body bib taps,15 mm cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule for 15mm bore complete all as specified and directed by Engineer - in - Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

S&F in repair water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) including all joints and making good to the floor complete all as specified including CI 'P' trap/S trap all as specified and directed by Engr-in-charge.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, PVC connections 15 mm size with PTMT nuts of length 450 mm ,including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed by Engineer - in - Charge.

S&F, in repair vitreous china wash hand basin table top type, including brackets, 32mm bore brass chromimum plated waste coupling & 32mm bore low density ployethylene (LDPE) flush pipe of pressure rating 6Kgf/Sq cm (1.00 M long) complete, including 15mm bore 450 mm length PVC connection with PTMT nuts.

S&F in repairs low density polyethylene pipes (LDPE) 32 mm dia and 1000 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer in charge.

Supply only fancy type swan neck pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure of 15 mm bore diawith or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer in charge.

S&F hat pegs and hooks (cloth hanger with six peg set each) complete all as specified.

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron 'Y' tee sand cast fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

M&L for CI floor trap 100 mm with anti cockroaches grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

M&L for CI floor trap 75mm with anti cockroaches grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

M&L bands straps supports or stays for rainwater ventilating pipes including bolts confirming to Fe 290 Gde E-165 all as specified and directed by Engr-in-charge.

Taking up or down for 25mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 15mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 20mm bore, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 25mm bore, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

S&F push type Metropole flush valve, made of brass with CP finishing suitable for 40mm CPVC pipe complete all as specified and directed by Engineer - in - Charge.(make - Jaquar, Prayag-BEA-35, ESS ESS or equivalent and approved by AO.

S&F CPVC pipes ISI marked IS 157778 with all brass fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors of 40mm bore dia ( SDR 11. of make:- astral or equivalent of supreme / finolex )

S&F in repairs vitreous china urinals, half stall type flat back complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe including waste pipe and trap complete all as specified and directed by Eng in charge.

S&F Urinal spreader of PTMT any colour for fixing 15 mm dia pipe complete all as specified and directed by Engineer in charge.

M&L for granite (of any type) 20 mm thick machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, rounding of edges (moulding of edges) and polishing complete laid over 15 mm thick screed bed in CM 1:4 etc all as specified and directed by Engineer in charge.

Demolition of RCC as in Roofs, floors ( other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by EIC.

M&L for RCC nominal mix 1:1 1/2: 3 (using 20mm graded aggregate ) as in slabs suppotred on walls, beams and columns complete all as specified and directed.

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer - in - Charge.

S & F for 20mm dia Gun metal , gate or globe valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F for 25mm dia Gun metal , gate or globe valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F steel windows with side hung shutters including projecting types hinges with steel handles and steel peg stay complete with glazing bars complete with dove tailed or welded including one coat of red oxide primer all as specified and directed by Eng-in-charge.

S&F steel windows with side hung shutters including projecting types hinges with steel handles and steel peg stay complete without glazing bars complete with dove tailed or welded including one coat of red oxide primer all as specified and directed by Eng-in-charge.

S&F Harrison rails mild steel chromium plated with fixing brackets, stops, rollers etc 20mm bore dia complete all as specified and directed by engr-in-charge.

S&F plain mild steel sheeting 0.80mm thick in expansion/bldgs joints gutter valley, hips with screw and fastners including all fixing cleats etc complete all as specified and directed by engr-in-charge.

Material and labour for repair of chajja facia using cement mortar (1:3) n.exc 300 mm girth finishing the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.

Providing & Applying corrosion resistance single component, Polimer modified cement mortar to patch up the damaged concrete section in planks of 25mm thickness. Providing and applying corrosion resistance single component, polimer modified, fibre reinforced cementitious repair mortar having water powder ratio in the range of 0.12-0.14 and the mixed density of around 2300+50 kg/m3. The repair mortar shall achieve a minimum compressive strength of 60 N/mm2 @ 7days when tested as per BS :6319: Part 2 and a flexural strength of 19 N/mm2 when tested as per BS :6319 part 3. It shall achieve a minimum adhesionb bond strength of 5 N/mm2 when test on standard electometer as per ASTM C 881 . The tensile strength shall be a minimum of 6N/mm2 when tested as per BS6319: part7.( Material Make: Sika-Sikadur 32LP/Fosroc-Nitobond SBR(EP)/Pidilite Dr Fixit Super Latex(EP), Asian paint repair polymer or Techno commercial equivalent make approved by GE in writing from E-in-C branch approved list height upto as per site complete all as specified and directed.

M&L for Mild steel work as ISMB,joists channel,angle or tee section fixed adjacent to ceiling and embedding in floor and brickwork including cutting welding and the like including caps.bases,splices etc,built from one or more beam or channel section or angle with plates including all lattice bars, stiffeners,gusset plates including necessary welding,rivetting etc.confirming to Fe 410 (Gde E-250) quality A etc all as specified and directed by Engineer-in-charge.

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and as directed by Engineer-in-charge.

Grouting, injecting two part, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and as directed by Engineer-in-charge. Note :- Mode of measurement: per kg of material consumed Make: Sika - SikaDur 52 LP/ Fosroc- Conbextra EP 10/ Pidilite Dr Fixit Epoxy Injection Grout or equivalent make approved by GE in writing from E-in-Cs Br approved list.

M&L for providing and applying jacketing around coloumns/beams/Rcc or any other RCC members with micro concrete having a minimum compressive strength of 60N/mm2@ 28 days when tested as per ASTM C-109 and a flexural strength of 6 N/mm2 when tested as per ASTM C580 . The tensile strength shall be a minimum of 2.5 N/mm2 when tested as perASTMC 307. It shall provide an unrestrained positive expansion of upto 0.405 when tested as per ASTM C307. including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete. Note: Reinforcement shall be measured and paid seperately.(Rates including jacketing, formwork and microconcrete) complete all as specified and directed.(Make: Sika-SikaDur 32LP/ FOSROC-Nitobond SBR (EP)/Pidilite Dr Fixit Super Latex (EP) ,make approved by GE in writing from E-in-C' Br approved list.

Supply for Pipe supporting clamping - single pipe of dia 110mm(4'') down take pipe fixing done with clamping system consists of profile bracket+continuous slotted C channel +U bolt rubber sleeve mounted system running vertically with wall distance 75mm (3'') pipe support clamping made of : 1. Profile bracket having wall distance 75mm(3'') made of low carbon Hot roll guage corrected oil pickled and drawn(HROPD) Steel (IS 1079): material size 32mm X3mm with ribbs and notch are hot dip galvanized+ Zn Al flake coated having salt spray test(test method-ASTM B-117-2019) results 2000hrs with SS304 Hex flange bolt with serration 5/16x3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex flange nut BSW 5/16X18X8X13 with serration as per DIN 6923 .2. Continuous slotted "C' Channel with ribs to be used of size 250mm (10'') made of low carbon hot roll guage corrected oil pickled and drawn(HROPD) sTEEL (is 1079) are hot dip galvanized+Zn Al flake coated with material thickness of 3mm. 3. U bolt rubber sleeve mounted are made of low carbon mild steel with rod diameter 7mm approx: Zn Al flake coated with noise absorbing semitransparent ribbed silicon rubber sleeve; with Hex flange nut BSW5/16X18X8X13 with serration set as per DIN 6923-Zn Al flake coated.Hotdip galvanizing: as per IS 2629(1985)-610grams/m2(>85 microns). Material grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material qty: for one unit: 1. Profile bracket wall distance 75mm(3'')-02 Nos. 2. Continuous slotted C channel of size 250mm(10"). 3. U bolt rubber sleeve mounted for 110mm(4")CI or PVC pipe dia-01 No: and 4. Fixing nail Zn coated of thickness 6.5mm and length 63mm(2.5'')-04Nos. Fixing detail: Pipe support clamping unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bathinda ZoneTechnical drawing(TD) of factory made pipe supporting system:DRG NO-BTD-916.

Supply for Pipe supporting clamping - single pipe of dia 75mm(3'') down take pipe fixing done with clamping system consists of profile bracket+continuous slotted C channel +U bolt rubber sleeve mounted system running vertically with wall distance 75mm (3'') pipe support clamping made of : 1. Profile bracket having wall distance 75mm(3'') made of low carbon Hot roll guage corrected oil pickled and drawn(HROPD) Steel (IS 1079): material size 32mm X3mm with ribbs and notch are hot dip galvanized+ Zn Al flake coated having salt spray test(test method-ASTM B-117-2019) results 2000hrs with SS304 Hex flange bolt with serration 5/16x3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex flange nut BSW 5/16X18X8X13 with serration as per DIN 6923 .2. Continuous slotted "C' Channel with ribs to be used of size 250mm (10'') made of low carbon hot roll guage corrected oil pickled and drawn(HROPD) sTEEL (is 1079) are hot dip galvanized+Zn Al flake coated with material thickness of 3mm. 3. U bolt rubber sleeve mounted are made of low carbon mild steel with rod diameter 7mm approx: Zn Al flake coated with noise absorbing semitransparent ribbed silicon rubber sleeve; with Hex flange nut BSW5/16X18X8X13 with serration set as per DIN 6923-Zn Al flake coated.Hotdip galvanizing: as per IS 2629(1985)-610grams/m2(>85 microns). Material grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material qty: for one unit: 1. Profile bracket wall distance 75mm(3'')-02 Nos. 2. Continuous slotted C channel of size 250mm(10"). 3. U bolt rubber sleeve mounted for 110mm(4")CI or PVC pipe dia-01 No: and 4. Fixing nail Zn coated of thickness 6.5mm and length 63mm(2.5'')-04Nos. Fixing detail: Pipe support clamping unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bathinda ZoneTechnical drawing(TD) of factory made pipe supporting system:DRG NO-BTD-916.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.(Make of cable -Havells/Anchor and conduit pipe:-AKG/Plaza/Suprem)

All as per Srl item No -171 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No -171 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge

All as per Srl item No. 171 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge

All as Srl item No. 171 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer - in - Charge

All as Srl item No. 171 here in before but for call bell point complete all as specified and directed by Engineer - in - Charge

S & F in replacement modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed by Engineer - in - Charge

S & F modular Socket, 16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge

S & F modular switch 5/6 Amps single pole two ways complete all as specified and directed by Engineer – in - Charge.

S & F in repair modular socket 5 pin, type 5/6 Amps5 in 1 flush type 2 modular complete all as specified and directed by Engineer - in - Charge.

S&F modular bell push 5/6 Amps 230 V AC complete all as specified and directed by Engineer - in - Charge

S & F in repair socket outlet 5 pin, type 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F in repair Modular switch 1 way 16A, complete all as specified and directed by Engineer - in - Charge.

S & F in repair Modular stepped type fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge.

S & F ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S&F Buzzer AC 230 single poleVolt ding dong type complete all as specified and directed by Engineer - in - Charge.

S & F in repair compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified. (Make : Havells cat part no LUMILINEPLUSBS10WLED865SPCSS, Bajaj cat part no. BCLSB 10 WH, Crompton cat part no. LDL-10-CDL)

S & F in replacement of existing light fitting with LED batten with aliminium housing and integrated electronic driver, 20 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. (Make:Havells cat part No: LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part no.: BCLSBAL 20W CW ,Crompton cat part no. : CCS-100-20-65-HL2-DP-NWH)

S & F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F in replacement Water tight bulk head fitting,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery ,glass well,and including 10 watt LED lamp all as specified and directed by Engineer - in - Charge (Make:Havells cat part no : HEXAFT10WLED857SSYMBOPC, Bajaj cat part no. BIBWP 10W LED, Crompton cat part no. LBHP-10-CDL)

S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply , IP 66, Lumen 100lm/w , surge protection 4kv deviceand fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge (Make:Havells cat part no: ENDURAPEARLSL25WLED757SASYTOPCMP, Bajaj cat part no. BRLEP 25W LED WH, Crompton cat part no. LSTS-25-CDL-M)

S&F heavy duty metal body exhaust fan of 250mm sweep , 240 volt , complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in CM (1:4) white washing matching with existing color etc. (Make : Havells/ Orient/Crompton/USHA

S&F Heavy duty metal body exahust fan of 300mm sweep ,240 volt,copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc. complete all as specified and directed by Engineer - in - Charge

Supply and fix electric water heater, storage type steel body with glass coating SS tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed by Engineer - in - Charge

S & F bib taps,cast copper alloy with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule and fixed of size 15mm bore complete all as specified and directrd by Engineer in charge.

S & F gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed for GI pipes of size 15 mm bore complete all as specified and directrd by Engineer in charge.

Supply and fix in industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole & neutrtal with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 125A ,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs MCCB 4 pole 63 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

Supply and fix air cooled split unit air conditioner electric driven, single phase of capacity of 1.5 TR, BEE 5 star rated including Suitable stablizer complete all as specified and directed by Engineer - in - Charge

S & F of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge

S & F Rigid non-metallic PVC conduit 20 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed by Engineer - in - Charge

S&F tv socket having holes for 20mm conduit entry for tv connection all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 mtr wide and not ecxceedinf 1.5 mtr depth for laying of cables complete all as specified and directed by Engineer - in - Charge

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engineer - in - Charge

Removal of Excavated material n exceeding 50 mtr and depositing where directed complete all as specified and directed by Engineer - in - Charge

Supply and filling in Sand for Cable protection complete all as specified and directed by Engineer - in - Charge

Supplying and laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed by Engineer-in-Charge.

Supply and lay jointing and testing and commissioning in replacement of 25 Sqmmx4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supply and lay GI pipe 50 mm light grade for cable protection in walls trenches or any situation including clamp nut bolt etc complete all as specified and directed by Engineer-in-Charge.

Taking down and depositing of old unsv ceiling fans of any size in MES yard complete all as specified and directed by Engineer - in - Charge

M&L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed by Engineer - in - Charge

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed by Engr-in-Charge.

Taking down and depositing of old unsv exhaust fans of any size in MES yard complete all as specified and directed by Engineer - in - Charge

Taking down and depositing of old unsv geyser of any size in MES yard complete all as specified and directed by Engineer - in - Charge

J and P CONTRACTOR (BID ID -3356760)

AYUSH BUILDERS (BID ID -3356970)

Akarsha Enterprises (BID ID -3351424)

SHIVA CONSTRUCTION COMPANY (BID ID -3356814)