SPL REPAIR TO SHED No. T 06 INSIDE DEPOT AREA AT OD FORT ALLAHABAD.

Amount

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Brickwork with fly ash bricks old size, straight or curved on plan exceeding 6metre mean radius, built in CM 1:6, complete all as specified and directed.

Demolition of cement oncrete (un reinforced) of any description and in any position not secifically provided, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-2 (40mm graded stone aggregate), 75mm thick, as in ramp, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (20mm graded stone aggregate), 40mm thick, as in floor (laid in alternate panels) finsihing the surface even and smooth with using extra cement, complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water including removing of all rubbish off from the site, complete all as specified and directed.

Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Dismantling of AC corrugated or semi corrugated sheet including AC ridges as in roof or wall covering, complete all as specified and directed.

Dismantling timber scantlings, as in framed work, 40sq. cm and over in section, in any position, complete all as specified and directed.

Excavation in post holes or similar holes in loose/soft soil each not exceeding 0.5 cum, getting out, returning filling in and ramming earth in layers note exceeding 25cm well watering and removing surplus soil to a distance not exceeding 50m and making good surface where ever required, complete all as specified and directed.

Plain cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate), as in mass concrete in foundation filling including sub base of floors, complete all as specified and directed.

Plate girder or single stanchions (ISMB-100), built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections conforming to Fe 410-W (Gde-E- 250) quality-A, in repair, complete all as specified and directed.

Second class hard-wood in scantlings, clean sawn, timber framed and fixed, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering / cladding to wall, valley gutter, ridge hips etc, fixed with self tapping screws, complete all as specified and directed.

Fibre glass reinforced translucent corrugated sheeting 2mm thick, with two corrugations side lap fixed with coach screw and washer in roof, wall etc, complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (20mm graded stone aggregate), 50mm thick, as in floor (laid in alternate panels) finsihing the surface even and smooth, complete all as specified and directed.

Wearproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner), 20mm thick, complete all as specified and directed.

Supply only metallic hardner, complete all as specified and directed.

Steel windows factory made with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, inlcuding two coats of synthetic enamel paint over a coat of red oxide primer after preparation of the new steel surface, fixed in repair, complete all as specified and directed. Note: Red oxide primer shall be already cattered by the factory.

Steel windows factory made with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, inlcuding two coats of synthetic enamel paint over a coat of red oxide primer after preparation of the new steel surface, fixed in repair, complete all as specified and directed. Note: Red oxide primer shall be already cattered by the factory.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame (with and including punching or drilling out old glazing pins/spring clips and providing and fixing new ones) or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

Sheet glass, 3mm thick, ordinary quality and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash, complete all as specifed and directed.

Complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, filling depressions of scrapped surfaces with wall care putty and applying uniform layer of 1mm thick wall care putty (Make: JK white or Birla) including preparation of surfaces by rubbing with appropriate size of sand or emery paper and applying two coats of cement base paint on walls surface, complete all as specified and directed.

Preparation of old wooden surfaces and applying one coat of synthetic enamel paint on old wooden surfaces of any description, over 10 cm width or girth, complete all as specified and directed.

Preparation of new wooden surfaces exc 10 cm width or girth with sand or emery paper & applying two coats of synthetic enamel paint over a coat of pink primer , complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

R K CONSTRUCTION AND ENGINEERING

M/S A P CONSTRUCTION

MOHAMMAD RIZWAN CONTRACTOR

M/S PRAMOD SINGH ASSOCIATE

MS BHAVANA ENTERPRISES

M/S ATUL CONSTRUCTION

VAKRATUNDA CONSTRUCTION CO

shweta constructions

Shivagya Engineering

shirdi sai builders

ms shanti sons