Repair to water proofing treatment and sunken treatment to certain building including heat reflective painting in KLP location and MD Accn under AGE B/R-II at Suratgarh Mil Stn

Amount

Demolition of cement concrete (unreinforced) roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified & as directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified & as directed. Note : Contractor shall make arrangement to protect tiles, plumbing items, sanitary fittings, etc under the slab, etc by gunny bags with sand or any other suitable arrangement and quoted rates shall deemed to include this aspect.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Dismantling of brick tiles or roof tiles or terracing tiles single layer on roofs, complete all as specified and as directed. Note : Tiles shall be dismantled carefully and stacked properly including segregating the serviceable & unserviceable tiles as directed. Serviceable tiles shall be reused under the respective item of this Schedule.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Removing material obtained from serial item No. 7.00 here-in-above to a distance exc 250 metre but not exc 500 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

M&L for PCC 1:5:10 type E2 using 40mm graded crushed stone aggregate as in sunken filling and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete M-20 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified & as directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. MS stay shall be provided at the bottom to steady the frame complete as specified by the manufacturer and as per directions of Engineer-in-Charge.

Supply and fixing to existing door frames 30mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer-in-Charge.

S&F butt hinges of size 100mm medium weight, cold rolled mild steel (ISI marked) including welding to angle iron frame where required complete all as specified and as directed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 200mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed.

M&L for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface by forced application over and including applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg/sqm including cleaning of surface complete all as specified and as directed.

M&L for wire brushing and cleaning concrete surface on top of roof surface and providing 40mm thick cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) complete all as specified and as directed.

M&L PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in concave shape benching (gola) of 80mm radius at junctions of roof/terrace with parapets/ side walls with surface finished even & smooth without using extra cement complete all as specified and as directed.

M&L for 40mm thick brick tiles, joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, laid on roof over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.

All as per serial item No. 24.00 here-in-before but except brick tiles complete all as specified and directed. Note : Old serviceable brick tiles retrieved from serial item No 6.00 here-in-before shall be used under this item.

M&L for joint free non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of ceiling, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for preparation of surfaces on roof and applying three coats of heat reflective paint complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of walls & applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint complete all as specified & as directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, including hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including dismantling and taking up or down steel water tubing and connections of 15mm bore complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including dismantling and taking up or down steel water tubing and connections of 20mm bore complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 32mm bore with & including all fittings complete, fixed to floors as spouts in sunken portions, complete all as specified and directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore complete as specified in SSR Part-I and as directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore complete as specified in SSR Part-I and as directed.

Disconnecting existing serviceable rotational moulded polyethylene water storage tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity not exc 500 litres including cleaning & removing all scale & dirt etc from tank with gunny bags, cleaning with fresh water and bleaching powder, complete all as specified and as directed.

Disconnecting existing serviceable rotational moulded polyethylene water storage tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity exc 500 litres & not exc 1000 litres including cleaning & removing all scale & dirt etc from tank with gunny bags, cleaning with fresh water and bleaching powder, complete all as specified and as directed.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, including cast iron ‘P’ or ‘S’ trap 100mm dia and including connection to trap including cement concrete and to flushing pipe, antisyphonage pipe etc, including making good to floor complete all as specified and as directed. Make : Parryware, Mode No. C0133/Jaquar Model No. ESSCO ECS-WHT-453/Cera Model No. CABLE S3020105/Somany

S&F in repairs vitreous china wash down squatting pan (Pedestal pattern), white, including cast iron ‘P’ or ‘S’ trap 100mm dia and connection to trap including cement concrete and to flushing pipe, anti-sypohonage pipe etc., including making good to floor complete all as specified and as directed. Make : Parryware, Mode No. C0287/Jaquar Model No. ESSCO ECS-WHT-551SNPP/Cera Model No. S1053102 (Snow White)/Somany : SUPER

S&F in repair seat and cover for pedestal pan complete all as specified & as directed. Make : Parryware, Mode No. E8309/Cera Model No. B1510121/Somany : Standard Plus Seat Cover

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified & as directed. Make : Parryware, Mode No. SLIMLINE UNO E8348/Cera Model No. B1010109/Somany : SUPER SINGLE FLUSH

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.

S&F in repairs PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed.

S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete all as specified & as directed. Make : Cat Part No. ‘54702A1’ of ‘Parryware’ / Cat Part No. ‘F2002101’ of ‘Cera’ / Cat Part No. ‘MQT-508KN’ of ‘Jaquar’ / Cat Part No. ‘9202’ of ‘Prayag’ /Cat Part No. ES-'507' of MARC or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs mixer for Kitchen sink, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with shaped CP brass nipples screwed for 15mm bore connections complete all as specified as directed. Make : Cat Part No. ‘G4935A1’ of ‘Parryware’ / Cat Part No. ‘F2002461’ of ‘Cera’ / Cat Part No. ‘TQT-516A’ of ‘Jaquar’ / Cat Part No. 'ES-516-A' of 'MARC'/Cat Part No. '272201250051' of SOMANY or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs 15mm dia Brass L Bend CP mixer for 'Hot' & 'Cold' water screwed down for iron pipe and fixed, with or without lettered 'Hot' & 'Cold' with long screwed shanks and flynuts, screwed for iron pipe fancy type connections complete all as specified as directed. Make : Cat Part No. ‘T1916A1’ of ‘Parryware’ / Cat Part No. ‘F2002401’ of ‘Cera’ / Cat Part No. ‘MQT-517BKN’ of ‘Jaquar’ / Cat Part No. 'ES-517-B' of 'MARC'/Cat Part No. '272201250011' of SOMANY or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs 15mm bore bib tap, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, including CP brass wall flange, complete all as specified & as directed. Make : Cat Part No. ‘G4706A1’ of ‘Parryware’ / Cat Part No. ‘F2002152’ of ‘Cera’ / Cat Part No. ‘COS-103107’ of ‘Jaquar’ / Cat Part No. ‘9208’ of ‘Prayag’/Cat Part No. '272211250031' of 'Somany'/Cat Part No. ES-511-A of 'MARC' or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified & as directed.

S&F in repair 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & as directed.

S&F in repair 25mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & as directed.

S&F 15mm bore Angle valve, fancy type and cup of cast copper alloy chromium plated, screwed down, high pressure with crutch of butterfly handle, screwed both ends for iron pipe or for union complete all as specified & as directed. Make : Cat Part No. ‘G9004A1’ of ‘Parryware’ / Cat Part No. ‘F8040201’ of ‘Cera’ / Cat Part No. 'TQT-526N’ of ‘Jaquar’ / Cat Part No. ‘7210’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Shower rose, round type, brass, chromium plated, Fancy type, 100mm dia (minimum) with arm 225mm long (Minimum) or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe of 15mm bore or union complete all as specified and as directed. Make : Cat Part No. ‘T9809A1’ of ‘Parryware’ / Cat Part No. ‘F7010213AB’ of ‘Cera’ / Cat Part No. ‘BOS-87’ of ‘Prayag’/ Cat Part No. ES-549 & ES-536 of 'MARC'/Cat Part No. '272220080011' of SOMANY or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repair Health Faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixing to steel pipe of 15mm bore or union complete all as specified and as directed. Make : Cat Part No. ‘ESSCO ALE-ESS-585’ of 'Jaquar’ / Cat Part No. ‘F8030107AB’ of ‘Cera’ / Cat Part No. '272150680051' of SOMANY or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed. Make : Cat Part No. ‘ESSCO AEC-1111NB’ of ‘Jaquar’ / Cat Part No. ‘F5007103’ of ‘Cera’ / Cat Part No. '272130740051' of SOMANY or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Towel ring brass chromium plated with round flange fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified & as directed. Make : Cat Part No. ‘ESSCO AEC-1121N’ of ‘Jaquar’ / Cat Part No. ‘F5003105’ of ‘Cera’ / Cat Part No. '272130740071' of SOMANY or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

Supply and fixing 100mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.

Supply and fixing 75mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.

S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 100mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.

S&F in repairs 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.

S&F in repairs 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.

S&F in repairs 100mm bore cast iron bends (any radius), with duck's foot or heel rest with oval access door complete all as specified & as directed.

S&F in repairs 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed.

S&F in repairs 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls fixed in repair complete all as specified & as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls fixed in repair complete all as specified & as directed.

S&F in repair 110mm bore PVC (SWR) bend, any redius complete all as specified & as directed.

S&F in repair 110mm bore PVC (SWR) Junction, Single (single ‘T’) equal or unequal with access door complete all as specified & as directed.

S&F in repair 110mm bore PVC (SWR) bends ISI Marked any radius with access door complete all as specified & as directed.

S&F in repairs PVC (SWR) 'P’ trap 100/110mm bore for fixing with WC complete all as specified & as directed.

S&F in repairs PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete all as specified & as directed.

S&F in repairs 32mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S&F in repairs 32mm dia PVC flexible waste pipe 75cm long for WHB/urinal/sink, complete all as specified and as directed.

M&L for preparation of new surface and mixed with cement and water in the ration 1:1.5 by volume using DR FIXIT PIDICRETE URP chemical on floor and vertical surface of sunken floor as per manufactures instructions complete all as specified and directed by Engineer-in-Charge. Note : No extra shall be paid to the contractor for account of liquid water proofing compound shall be deemed be to included in the quoted rates of the contractor.

M/S MANIRAM BISHNOI

Gill Construction Co

M/S KARNI CONSTRUCTION COMPANY

MSR INFRATECH