WELCOME MAINTENANCE TO OFFICERs/JCOs/ORs MD ACCN AND REPAIR/REPLACEMENT TO PERISHED WORNOUT JOINERY CUPBOARD, KITCHEN SHELVES IN MD ACCN IN JCOs MD/ORs MD/OFFICERs MD AND OTM ACCN AT N AREA UNDER GE CHANDIGARH.

Amount

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description not exc 1 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.

Dismanntling of plain or corrugated AC roof sheet, any gauge, thickness, including nainital or similar pattern roof covering etc complete all as specified and directed.

Dismantling Plain or corrugated fiber sheet etc any gauge, thickness, complete all as specified and directed.

Taking up or down kitec pipe and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (up to 4th storey of building ) complete all as specified and directed by Engr-In-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 250 & n.exc 500 ltr in capacity complete all as specified

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 500 & n.exc 1000 ltr in capacity complete all as specified

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 250 & nexc 500 ltr), Complete all as specified and as directed

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 500 & nexc 1000 ltr), Complete all as specified and as directed

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

S&F for tank Nipple suitable for HDPE water tank 20mm tank nipple cast iron min weight 45gms complete all as specified.

S&F for tank Nipple suitable for HDPE water tank 15mm tank nipple cast iron min weight 45gms complete all as specified.

M&L for MS 100mm long fasner with washer and bolt etc complet all as specified.

Supplying & fixing in repairs of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete all as specified and directed by Engineer-in-Charge.

25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in levelling concrete etc. complete all as specified and directed by Engineer-in-Charge.

Reinforced Cement Concrete Nominal mix ( 1:1.5:3) using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete including formwork complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles double charged light shade 8-9 mm thick (Square/rectangular) polished, area of each tile exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc. laid and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 laid over and inculding 15mm thick bedding of layer of cement sand mortar (1:4) complete all as specified and as directed.

Glazed ceramic coloured tiles 450 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 to match tiles complete all as specified and directed by Engineer-in-Charge.

M&L out door/parking tiles heavy duty for light traffic non skid, anti scratch, heavy grip, vitreous/semi vitreous coloured, unique designs tiles 8 to 10mm thick area of each tile of size 300mmX300mm, in floors, parking/outdoor tiles etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM(1:4), complete all as specified and directed.

Granite 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab flooring 20-22 mm thick,SIZE 55 CM x 55 cm laid over & including 15 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab 20-22 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 EXCEPT BRICKS complete all as specified and directed by Engineer-in-Charge.

M&L for raking out joints/ pointing to brick to brick tiles 30cm by 15cm laid flat as in floors, roofs, ceilings, chajjas, etc compound complete all as specified.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, (up to 4th storey of building ) complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Rendering 10 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of cement base paint on walls over and including a coat of primer (up to 4th storey of building ) including preparation of surface complete all as specified and directed.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of chalk whitening including preparation of surface complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying one coat of interior grade acrylic emulsion over a coat of primer on old walls including preparation of surface complete all as specified and directed.

M&L for complete removal of existing surface and applying two coats of oil bound distemper over and including a coat of primer and 1 mm wall care puty on wall surfaces (upto 4th story of bldg), complete all as specified and as directed.

Preparation of walls brooming down, applying wall care putty 1 mm thick etc (up to 4th storey of building ) complete all as specified and directed by Engineer-in-Charge.

Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceilings/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

Preparation of old plastered surfaces of wall and applying one coat of oil bound distemper (Ist quality) on walls including preparation of surface complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying one coats of cement base paint on walls including preparation of surface (up to 4th storey of building ) complete all as specified and directed.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old treated wooden surfaces,inluding complete removal of existing treatment of any description with scrubber machine and applying two coat of french polishing inluding filling cracks/holes with filler material complete all as specified and as directed.

M&L for one coat of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

M&L for one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

25 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match supplied and fixed complete all as specified and directed by Engineer-in-Charge.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles),With Wood free EPS with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.

35 mm thick factory made Plain, framed, panelled shutters of 2nd class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkat complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with glazing bars and without glazing bars (Double shutter ) dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

Factory made box type steel ventilator with top hung or fixed half glass and half wire mesh portion shutter including projecting type hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.Note:Sheet glass and wire gauge will be measured and paid separately against respective items

Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge

M&L for steel rolling shutters , (with lath thickness 1.25 mm ) with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and , erected in position as indicated, complete push pull or manual type gear operated type with bevel gear box and crank handle complete all as specified and directed by Engineer-in-Charge.

S&F for Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 200 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 125 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 100mm size medium weight cold rolled mild steel of any frame as wooden/metal through nut&bolt/welding complete all as specified and directed.

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

150 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.

125 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.

100 mm long Aluminium handles, Fancy type,cast type,anodised complete all as specified and directed by Engineer-in-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 150 mm complete all as specified and directed by Engineer-in-Charge.

Peg stays of aluminium alloy anodised 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F in Hasp and staple 125 mm alluminum anodised complete all as specified and direccted.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repair Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, mild steel bright finish (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished complete all as specified and directed.

Aluminium body peg set of 06 pegs complete all as specified and directed by Engineer-in-Charge.

M&L for door closer hydraulically regulated, designation No. 1 universal type, aluminium body suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

M&L for floor door spring hydraulically regulated, cast iron body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed.

Stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples fixed in repair complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge.

4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

S&F 5 mm thick sheet glass pane tinted/plain/Figured glass type, with 5 micron thick black film ordinary quality and ruber, cleting, silicone,glazing with oil putty etc in each pane complete all as specified and directed.

M&L for toughned glass 12mm thick as in hinged doors, partitions automatic doors and similar work including ss hinge, ss handle 2 Nos floor double action hydraulic door spring fixing all ccessories, cutting to shape, drilling holes required and ruber, cleting, silicone,glazing with oil putty et complete all as specified and directed.

M&L for toughned glass 12mm thick as in frameless toughened glass of approved brand and manufacture, all complete all ccessories, cutting to shape, drilling holes required and ruber, cleting, silicone,glazing etc complete all as specified and directed.

Material & labour for 25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging conforming to Fe-290 (Gde E-165), also fastening and fixing complete all as as specified and directed by Engineer-in-Charge.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, Fe-410-W (Gde E-250) complete all as as specified and directed by Engineer-in-Charge.

Supply and fixting of roller blinds with power coated plain cassette of approved make in white colour made of extruded non-rusting aluminium ally 1.25mm thick, with 1.5mm thick internal tube of required dia made of non-rusting aluminium with a pocket to insert the fabric inside of it with end plugs & operating mechanism made up of ABS plastic with ball chain of 1.50mm thickness for lowering or raising the blind and can be positioned on right of left part part of blind. The ball chain shall be minimum 1.5mm diameter cord with 4.5mm diameter acetyl balls molded co-axiallyto it on 6mm pitch to form an endless ball chain. The brackets should be zinc plated/power coated mild steel. Bottom rail should be gallent (3mm dai) witch fabric covered and square shape made of non-rusting aluminium powder coated with 1.50mm thick . The babric should be enclosed in the suitable created pocket along with tube. The channel shall be cloused from the sides with endcaps to give a neat look. The fabaric has to be blackout 100% polyester, weight 335g/sqm (+5%), 0.53mm thickness with excellent hanging and tearing strength of approved color complete as per direction of Eng-in-Charge.

Pre-painted galvalume aluminum zinc coating profile sheet GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre- painted galvalume aluminum zinc coating profile sheet GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping s crews as complete all as specified and directed.

M&L 2 mm thick Fibre glass reinforced transparent plain/corrugated sheeting of white or any colour fixed with coach screw and washer in roof, wall etc complete all as specified.

S&F 17/18 mm HDMR board exterior grade, prelaminated both side with 1mm thick decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in kitchen cabinets,cupboards complet all fitting jointing etc complete all as specified and as directed.

S&F 8 mm HDMR board exterior grade, prelaminated one side with 1mm thick decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in kitchen cabinets,cupboards complet all fitting jointing etc complete all as specified and as directed.

PVC hollow wall panelling 5mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including dismantling of walls and ceiling boards/wall paneling or insulation board any thickness, including cover fillets complete all as specified and directed

PVC lower wall panelling 5mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including dismantling of walls and ceiling boards/wall paneling or insulation board any thickness, including cover fillets complete all as specified and directed

Providing & fixing false ceiling at all heights with With Semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module ofs1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and Lshape level adjuster of size 85x25x2mm .Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

S&F in repair stainless steel plain basket, cutlery pan basket ,grain trolly, plate basket,cup soucer,partition, or any other basket of any description/pattern as approved by GE fixed with sliding channel revolving wheels , fixed to wood based frame work , complete all as specified and directed.

S&F Stainless steel handle, fancy type, 125 mm size and fixed in position with stainless steel screws, ISI marked, suitable for rubber wood shutter drawer(s), complete as per the sample kept in the office of Engineer-in-Charge.

S&F Stainless steel auto close (dada) hinges suitable for moulded shutter fixed in position with stainless steel screws, complete all as specified and directed.

S&F in repair 50 mm long magnatic catcher of brassalloy body superior quality and fixed with screw complete all as specified.

S&F in repair telescopic channel/slider to fiacilitate drawer slide on steel ball bearing 400-500 mm long and fixed in position with stainless steel screws , ISI marked , suitable for cupboard drawers , complete as per the sample kept in the office of Engr-in-charge

S&F for PVC ruber door ceal fixed in door complete all as specified.

supply only white dhaga and taplone tap complete all as specified.

supply only gypsum screw (500 Nos screw each box) 1/2 inch, 1 inch, 1;1/2 inch 2 inch and 2:1/2 inch screw complete all as specified.

Supply and fix in repairs aluminium mortice lock, vertical type size 65mm, 2 lever complete all as specified and directed.

S&F in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat cover white, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap with connection complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F for vitreous china white wash basin with flat back of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including bottle trap/ PVC waste pipe as in repairs complete all as specified and as directed.

S&F single piece WC of size 365x655x765 with flushing cistern and connection pipe, P or S trap (closed pattern incl all necessary accessories like rag bolts, kitt /gel gasket etc, (including flushing cistern, pvc seat cover , jet and flush pipe complete all as specifed and directed.

S&F in repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing around urinal back in cement, grating and union for discharge pipe incl brass cp waste coupling, waste pipe, brass cp urinal spreader complete all as specified and directed.

S&F automatic sensor for urinal including all connections with flushing pipe and outgoing pipes fixed in repairs complete all as specified and as directed.

S&F for one piece PVC hydrolica plastic water closet seat cover (white coloured) closed pattern with flat bottom, cover and mild steel chromium plated or aluminium hinges device for pedestal pan fixed as in repair complete all as specified and as directed.

S&F in repair 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15 mm bore iron pipe as in repair complete all as specified and as directed.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap two way brass with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bottle tap brass with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs chromium plated, Brass, Jet spray including flexible pipe 15mm bore, screwed down, high-pressure pipe of 15 mm bore with wall flange fixed to wash down water closet (pedestal pattern) complete all as specified and directed.

S&F in repair Health faucet chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed

S&F Brass chromium plated shower rose 150mm square in shape with 450 mm long arm fixed in repair complete all as specified and as directed.

S&F in repairs toilet papper holder chromium plated with fixing to wall complete all as specified and directed.

S&F in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange, Complete all as specified and as directed

S&F for towel stand 450mmX600mm long of fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as complete.

S&F as in repair Sink with drainage board made of stainless steel of wall thickness 1mm thick for kitchen or laboratory with plug, washers and wastes, including bedding in cement sand mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x 160mm including waste pipe of suitable dia complete all as specified and as directed.

S&F in repair kitchen Plate Rack stainless steel having size 600mm x600mm x750mm (approx) made of stainless steel of wall thickness 1mm thick incl fixing to walls with fasteing screws, rubber/PVC beading /capping complete to sustain utensils weight upto 8-10 Kg, complete all as specified and directed.

S&F corner PVC shelf assembly (set of three of size 250x250mm,200x200mm &150x150mm) fixed in repair complete all as specified and as directed.

S&F PTMT shelf 450 mm x 124 mm any colour with brass chromium plated screws & PVC rawl plugs (Minimum weight 300 gm) IN REPAIR, complete all as specified.

S&F Bib tap standard of PTMT with flange Minimum weight 15mm-5gms any colour high pressure screwed for iron pipe and fixed .(Minimum weight 15mm-90gms fixed in repair incl PTMT extension Nipple (Minimum weight 15mm-18 gms) fixed in repair complete all as specified.

S&F in repair waste pipe 32mm dia, 800mm long with cup and nuts fixed to urinal complete all as specified & directed

S&F in repair Flush pipe of polyethylene of low or high density or PVC 32 mm dia, long bend, for low level cistern Complete all as specified and directed complete all as specified and directed.

S&F for CP soap dish holder in repair of complete all as specified and as directed.

S&F for PVC connections with PTMT nuts of length 600 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed by Engineer-in-Charge.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) trap ‘P or S trap’ including jointing with solvent cement 100 mm bore fixed in repair complete all as specified and directed by Engineer in Charge.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass elbow fittings, ISI marked for CPVC pipe outer diameter 16 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass TEE fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 UNION fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Female Brass Threaded Adaptor (FTA/ FBTA) fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F tubes 15 mm, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.

Re-fixing only tubes, any grade, to walls and ceilings or laying in floors 15 mm, `medium grade' galvanised, with all fitting and fixed clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.

S&F Kitec all fittings tee, elbow, coupler 16/20 all fittings in kitec and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed.

S&F Kitec all fittings tee, elbow, coupler 20/25 all fittings in kitec and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed.

S&F Kitec all fittings tee, elbow, coupler 12/16 all fittings in kitec and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as directed and specified by Engineer-in-Charge.

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 86,166.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

M/s Super Trading Corporation (BID ID -3440243)

MANDEEP ENTERPRISES (BID ID -3438679)