SPECIAL REPAIR TO BLDG NO CD 14, BLDG NO TA-13 AND EXISTING DRAIN, CULVERT AND CONNECTED ITEMS OF 316 MED REGT AND BOUNDARY WALL FENCING HARDSTATION AND CONNECTED WORKS OF BLDG NO AFI 7 AT AJMER MIL STATION UNDER GE NASIRABAD

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames area n. exc 1.50 Sqm (w/o taking off shutters from frames) and removing from site, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames area exc 1.50 Sqm and n. exc 4.00 Sqm (w/o taking off shutters from frames) and removing from site, complete all as specified and directed by Engr-in-Charge.

M & L for Non - skid coloured ceramic tiles 400 x 400 x 7 to 8 mm thick (square), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M & L for Coloured glazed ceramic tiles in vertical surface 300x 450x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface complete all as specified and directed by Engr-in-Charge.

M & L for Granite work (Jet/Telephonic Black) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter basins, urinal partitions etc. and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed by Engr-in-Charge.

M & L for 50 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight, complete all as specified and directed by Engr-in-Charge. Note :- Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection

S &F made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 50 mm x 75 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company, complete all as specified and directed by Engr-in-Charge.

S & F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed by Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

S & F factory made Steel window/ ventilator glazed & gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary cooler arrangement in window & guard bars all as shown in drg No. CEBZ/TD/14/11 sh No 1/7 to 7/7 & complete all as specified and directed by Engr-in-Charge. (Make:M/S Jangid and equivalent).

S & F for 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square not excc 0.5 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

S & F 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.

S & F 150 mm long 10mm dia Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-Charge.

S & F 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed by Engr-in-Charge.

S & F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and directed by Engr-in-Charge.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed by Engr-in-Charge.

Demolition of brickwork or stone/boulder masanory,laid dry below or above ground level and removing material from site complete all as specified and directed by Engr-in-Charge.

M & L brick work with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6, complete all as specified and directed by Engr-in-Charge.

M & L for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

M & L for 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified and directed by Engr-in-Charge. Note : WPC shall be measured and paid separately.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed by Engr-in-Charge.

M & L for preparation of newly/old plastered surface of wall or ceiling and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applyingTwo or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed by Engr-in-Charge.

M&L for two coat of synthetic enamel painting to steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc. complete all as specified and directed by Engr-in-Charge.

Taking down existing water proofing treatment of any description incl PCC padding, cement plaster any thickness from roof surfaces, cleaning of roof and prepairing it for further treatment incl make good necessary dubbing out wherever required and removing rubbish from site complete all as specified and directed by Engr-in-Charge.

M & L for screed plaster 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces mixed with WPC incl necessary doubingout etc finished even and smooth for laying WPT without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces 75mm radius and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed by Engr-in-Charge.

M & L for APP modified polymeric water proofing membrane, 3mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3.00Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @1.20 Kg/Sqm over bitumen primer conforming to IS-3384 @0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @1.20 Kg/Sqm over APP membrane with all overlaps complete all as specified and directed by Engr-in-Charge.

M & L for PCC 25mm thick (minimum Consolidated thickness) Type B-0 (1:2:4), using 12.5 mm graded crushed stone aggregate as in padding finished even and smooth without using extra cement with existing slope with V shaped groves 6mm wide and 10mm deep @ 0.60 metre spacing both bays or part there of on top of padding and filled with mastic bitumen of 1:1 preparation complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up of rain water pipe /UPVC pipe line 100mm/75mm dia incl all fittings, complete all as specified and directed by Engr-in-Charge.

S & F for 110mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in floors or walls etc complete all as specified and directed by Engr-in-Charge. (Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

S & F for 75 mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint fixed to wall/floors etc complete all as specified and directed by Engr-in-Charge. (Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

S & F for 110 mm bore UPVC (SWR) bend with access door including jointing with solvent cement, complete all as specified and directed by Engr-in-Charge. (Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S & F 110 mm bore UPVC (SWR) ( singleT) equal or unequal including jointing with solvent cement, complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore UPVC (SWR) branch piece,single ( singleY) equal or unequal including jointing with solvent cement, complete all as specified and directed by Engr-in-Charge.

S & F for 75 mm bore UPVC (SWR) bend including jointing with solvent cement, complete all as specified and directed by Engr-in-Charge. (Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S & F PVC (SWR) 75 mm bore branch piece (Tee) fixed to walls with cement joint with or w/o ovel access door complete all as specified and directed by Engr-in-Charge.

S & F PVC (SWR) 110 mm bore PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge.

S & F PVC (SWR) 75 mm bore PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge.

M & L in repairs 75mm diaPVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate complete all as specified and directed by Engr-in-Charge.

M & L in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate complete all as specified and directed by Engr-in-Charge.

S & F brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and directed by Engr-in-Charge. (Make: Jaquar Essco/Prayag/Plumber/Jal)

S & F in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified and directed by Engr-in-Charge.

S & F in repair 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union, complete all as specified and directed by Engr-in-Charge. (Make: Jaquar Essco/Prayag/Plumber/Jal)

S & F in repair stop valves concealed type, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and directed by Engr-in-Charge.

S & F in repairs 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule, complete all as specified and directed by Engr-in-Charge. Make: Jaquar Essco/Prayag/Plumber/Jal

S & F in repair CP brass soap dish complete all as specified and directed by Engr-in-Charge.

S & F in repair rotational molded polyethylene water storage tanks white in colour, tripple layered with threaeded lid/cover, weight of tank should not be less than 36.00 Kg (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position complete all as specified and directed by Engr-in-charge. (Make:- Sintex/ Rotex/Vectus)

S & F in repairs 20mm bore Gun-Metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S & F in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes complete all as specified and directed by Engr-in-charge.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed by Engr-in-Charge.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed by Engr-in-Charge.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction, complete all as specified and directed by Engr-in-Charge.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 20mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction, complete all as specified and directed by Engr-in-Charge.

Excavation over area n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.

Removing excavated soil to a distance n exc 50m and depositing where directed at a level n exc 1.50m above the starting point complete all as specified and directed by Engr-in-Charge.

M & L for PCC 1:4:8 type D-2 as in foundation and mass concrete complete all as specified and directed by Engr-in-Charge.

S & F steel work in tublar truss including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade st 240 etc confirming to fe-410-W (Gde-E-250) quality-A, complete all as specified and directed by Engr-in-Charge.

S & F for M S plate or angle, channel, square cut or notched with riveted, bolted or welded attachment complete all as specified and directed by Engr-in-Charge.

S & F pre-painted galvatume aluminium zinc coating (AZ-150) GI based corrugated steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, incl taking down old ACC sheet complete all as specified and directed by Engr-in-Charge.

S & F pre-painted galvatume aluminium zinc coating (AZ-150) GI based plain steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

M & L for PCC 1:2:4 type B-1 (using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed by Engr-in-Charge.

M & L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over 50mm thick Sand cushioning layer etc complete all as specified and directed by Engr-in-Charge.

M& L for stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M& L for stone walling of random rubble(but except stone), uncoursed, well bonded, bedded and solidly hearted built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

Extra over random rubble stone walling for hammer dressing to face stones and dressing to face beds & joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exc 20mm complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

S & F Mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

M & L for rough cast plaster mix with crushed stone (6-10 mm) sand and cement in the ratio 1:1:1 over 15 mm thick rendering CM 1:4 as in under including two coat of cement base paint etc complete all as spd and directed by Engr-in-Charge.

Raking out joint/pointing to random rubble or polygonal rubble uncoursed or brought upto course in cement mortar, complete all as specified and directed by Engr-in-Charge.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto coursed in CM 1:4, complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in floors etc as directed and including necessary form work complete all as specified and directed by Engr-in-Charge.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete,brick etc and making good disturbed ground and preparing post holes for providing new post in any type of soil complete all as specified and directed by Engr-in-Charge.

Dismantling fencing wire mesh, any type etc, complete all as specified and directed by Engr-in-Charge.

M&L for angle iron as in fencing post incl cutting tops to shape as directed, drilling holes, notching for wire etc. Flat iron, fillets ( for securing wire mess) incl. all necessary drilling bolting or riveting etc confirming to Fe 290 Gde E -165, complete all as specified and directed by Engr-in-Charge.

M&L, for PCC 1:3:6 type C-2 in post holes and similar works complete all as specified and directed by Engr-in-Charge.

Supply only chain link MS zinc coating 60gms as per IS 4826 fencing of any mesh & 4mm dia of wire complete all as specified and directed. Note :- This item shall be measured and paid as per actual weight or standard weight as per SSR which ever is less.

Fixing only chain link fencing including line wires, any mesh size, type of standards rail straining bolts etc, 4mm dia wire, complete all as specified and directed by Engr-in-Charge.

S & F in repairs Galvanised 2 strand, steel barbed wire, 2.20mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, includdigng, securing or tying at crossings with and provisiion of galavnised (Zink coating 60 gsm) mild steel wire, staples or steel pins, etc as directed each line wire to measured complete all as specified and directed by Engr-in-Charge.

Providing & Fixing concertena coil fencing with punched tape concertena coil 600m dia 10m openable length (total length 90m) having 50 Nos rounds per 6m length, up to 3.0m height of wall with angle iron Y shaped placed 2.0m or 3.00m apart all complete as per direction of engineer-in-charge, with reinforced barbed wire tape (R.B.T.)/spring core (2.5mm thick) wire of high tensile strength of 165 Kg/Sqcm with tape (0.52mm thick and weight 43.478 gm/metre (cost of M.S. Angle shall be paid separately under relevant items.), complete all as specified and directed by Engr-in-Charge.

S & F of mild steel screw bolts (machine cut) with hexagonal or square heads at one end to be fitted with washers and one hexagonal or square nut, n.exc. 5cm long dia of neck 12mm, complete all as specified and directed by Engr-in-Charge.

S & F in repair 70-80 mm thick sand stone kerb of roughly rectangular stones not less than of size- length 60 cm and width 30 cm , dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck flush complete all as specified and directed by Engr-in-Charge.

M&L for MS framed work such as 12mm square guard bars conforming to Fe 290-0 or Fe 330-0 welded to ventilator/window /gate complete all as specified and directed by Engr-in-Charge.

S & F of framed work such as grills, gratings, cooler stands,doors,windows etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls, complete all as specified and directed by Engr-in-Charge.

Cleaning of drains of any size manually, removing of sludge and foreing material, roots of trees, trimming of branches of trees, removing of vegetable growth and bushes and removing from defence land from the site etc and making smooth flow of rain/waste water, complete all as specified and directed by Engr-in-Charge.

M&L for Cement concrete type C-2 (1:3:6) using 40mm Graded stone aggregate as in foundation of drains etc, complete all as specified and directed by Engr-in-Charge.

M&L for Cement concrete type B-1 (1:2:4) using 20mm Graded stone aggregate as in channel of drain, complete all as specified and directed by Engr-in-Charge.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement, including forms, mould and mitred/stopped ends, complete all as specified and directed by Engr-in-Charge.

M & L pre-cast RCC slab type B1 1:2:4 for manhole/ drain cover on site set in CM 1:4 etc, complete all as specified and directed by Engr-in-Charge.

M&L TMT bars of 6 to 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9 mm dia complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 metres wide and not exceeding 1.5 metres in depth and getting out in soft/loose soil, complete all as specified and directed by Engr-in-Charge.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed by Engr-in-Charge.

M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exceeding 200mm thick complete all as specified and directed by Engr-in-Charge.

M&L Providing PCC 1:3:6 type C2 using 20mm graded stone aggregate for bed concrete to drain pipes including packing under and haunching against the sides of pipes after that are laid and tested for 300mm RCC pipes, complete all as specified and directed by Engr-in-Charge.

S & F Reinforced concrete pipes class NP 2 300mm dia laid jointed complete with collars, complete all as specified and directed by Engr-in-Charge.

Demolition of Reinforced cement concrete pipe of 300mm dia of any description and in any position, complete all as specified and directed by Engr-in-Charge.

M & L for formwork to edges of concrete flats and similar works exc. 10 cm & not exc. 20 cm wide with rough finished surfaces etc, complete all as specified and directed by Engr-in-Charge.

M & L for Machine cut kota stone slab flooring of size 550 x 550 x 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc, complete all as specified and directed by Engr-in-Charge.

All as per item 104.00 above but pre-polished kota stone as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified and directed by Engr-in-Charge.

M&L PCC (1:4:8) Type D-2 using 40 mm graded stone aggregate in sub base surface finished even & fair, complete all as specified and directed by Engr-in-Charge.

Dismantling Asbestos cement (corrugated of semicorrugated etc), any gauge, thickness, roof coverings complete all as specified and directed by Engr-in-Charge.

Dismantling unframed timber fillets,rails,posts,rafters,purlins etc under 40 sqcm in section complete all as specified and directed by Engr-in-Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed by Engr-in-Charge.

Providing & Fixing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company, complete all as specified and directed by Engr-in-Charge.

S & F for 2nd class hard wood 30mm thick Plain, framed, panelled shutters (06 number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engr-in-Charge.

S & F IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed by Engr-in-Charge.

S & F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber complete all as specified and directed by Engr-in-Charge.

S & F MS helical door spring 150mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats, complete all as specified and directed by Engr-in-Charge.

S & F in repairs stainless steel type curtain rod 22 to 25mm dia as per sample, complete all as specified and directed by Engr-in-Charge.

S & F in repair of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample, complete all as specified and directed by Engr-in-Charge.

S & F in repair of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample, complete all as specified and directed by Engr-in-Charge.

S & F in repair of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia as per sample complete all as specified.

Demolition of cement concrete (reinforced) jali/louvers of any description and in any position not otherwise specifically provided for, including taking, complete all as specified and directed by Engr-in-Charge.

M&L for Providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin) corbels, brackets, etc. (of any section ndicated), with plain fair faces, including chamfers, weatherings, hroat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 (Type B1, 1:2:4 (using 20mm graded aggregate) complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper paint over a coat of 1mm thick putty complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper on walls over a coat of 1mm thick putty complete all as specified and directed by Engr-in-Charge.

M&L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer, complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc, complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc., complete all as specified and directed by Engr-in-Charge.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed by Engr-in-Charge.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc, , complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed by Engr-in-Charge. Make of wire: Polycab/Finolex/Havells, Conduit: Anchor/Polycab/Finolex

All as per item No. 129.00 here-in-before but One light point controlled by one, one way switch.

All as per item No. 129.00 here-in-before but One Ceiling fan/wall fan/exhaust fan controlled by one, one way switch.

All as per item No. 129.00 here-in-before but One three pin 5 Amp socket on same board with other switches.

All as per item No. 129.00 here-in-before but One three pin 5 Amp socket on independent board.

All as per item No. 129.04 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 1.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth, complete all as specified and directed by Engr-in-Charge.

S&F in repair switch piano flush type 5 amps, single pole one way 240 volts, complete all as specified and directed by Engr-in-Charge. Make : Cona / SSK / Havells

S&F in repair switch piano flush type 15 amps, single pole one way 240 volts, complete all as specified and directed by Engr-in-Charge. Make : Cona / SSK / Havells

S&F in repair Socket outlet 3 Pin 5/6 Amp flush type, complete all as specified and directed by Engr-in-Charge. Make : Cona / SSK / Havells

S&F in repair socket out let 2 in 1, 3 pin, 5 and 15 Amp flush type, complete all as specified and directed by Engr-in-Charge. Make : Cona / SSK / Havells

Supply and fixing stepped type ( switch type) electronic ceiling fan regulator flush type, AC, 230 volts , complete all as specified and directed by Engr-in-Charge.. Make : Cona / SSK / Havells

S&Fin repair ceiling rose surface bakelite 3 terminals 63.5 x 17 mm, complete all as specified and directed by Engr-in-Charge. Make : Cona / SSK / Havells

Taking down existing exhaust fan & wall mounted fan / Ceiling Fan and re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan, complete all as specified and directed by Engr-in-Charge.

S&F of lamp holder PVC/polycarbonate type with back plate, complete all as specified and directed by Engr-in-Charge. Make : Cona / SSK / Havells

S&F of LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose, complete all as specified and directed by Engr-in-Charge.

S & F LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired, complete all as specified and directed by Engr-in-Charge.

S & F ceiling fan 1200 mm sweep, 230 Volts, AC, 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos, down rod, canopy, shackle assy, complete all as specified and directed by Engr-in-Charge. Make:- Crompton/Bajaj/Havells/Khaitan

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size, complete all as specified and directed by Engr-in-Charge. Make :- Havells Cat Part No LHEOAP7UZ6W010 or equivalent model of Philips/Crompton

S &F and testing energy saving street light luminaire 15 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make:-Havells, Cat Part No. ENDURAPEARLSL15WLED757SASYTOPC, or equivalent model of Crompton/Philips

S & F of street light bracket made of 32 mm GI pipe, 1.2 mtr lenght fixed with two nos of clamp, nut and bolts, complete all as specified and directed by Engr-in-Charge.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable, complete all as specified and directed by Engr-in-Charge.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 240 volts suitable for housing MCB's including blanking plate, complete all as specified and directed by Engr-in-Charge.

S&F in repair of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Siemens

S&F in repair of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate, complete all as specified and directed by Engr-in-Charge.

S & F in repair of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Siemens

S & F in repair of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make: Havells/Legrand/Siemens

S & F in repair of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Siemens

S & F in repair of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Siemens

S & F in repair of MCB SPN, 240 volt, 36 to 63 Amp capacity, 10 KA, 'C' curve, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Siemens

S & F in repair of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Siemens

S & F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size, complete all as specified and directed by Engr-in-Charge.

M & L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing, complete all as specified and directed by Engr-in-Charge.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core

Supply and fixing tubes light grade GI tubing 50 mm dia with all fitting laid in trenches.

Supply and fixing MCCB 3 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA

MITTAL ENTERPRISES (BID ID -3103026)

SHREE BALAJI TRADING CORPORATION (BID ID -3118902)

Shree Sai Ram Enterprises (BID ID -3102039)