Construction of Community Hall, Drain, Road, Sump, Parkings etc at Additional Transit Accommodation at Vessu, Qazigund

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) in foundation trenches, drains, pipes and cables etc.(not exceeding 1.5 m in depth or 10 Sqm on plan, including dressing of sides and ramming of bottoms including all liftsand leads up to 50 meters using mechnical means.

Providing and laying of hand packed stone soling (size 150mm-230mm) before laying of mud mat compacted consolidated rammed filling the voids compacting all complete carriage upto site of work all head loads complete job.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Filling available excavated earth (excluding rock) in trenches, plinths, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

M20 : Reinforced Cement Concrete. P/L of Reinforced Cement Concrete of Nominal mix M20 1:1.5:3 mix

Supplying, filling with river sand /nallah muck in 20 cm layers including watering, compacting and dressing under flooring in ground floor.

Form work : Centring and shuttering including strutting, proping etc. And removal of form for:

Foundation, footing bases of columns etc for mass concrete

Columns, pillars, piers, abutments, posts and struts

Lintels,plinth beams, , girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform (Floor and roof beams)

Suspended floors, roofs, landings, balconies and access platform (slabs)

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete:Thermo-Mechanically- Treated bars.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 :6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) Extra for half Brick masonry in superstructure above plinth level upto floor V level.Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry.

12mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Ceilling (12mm cement plaster 1:6 mix).

Providing and fixing wood work in frames of doors, windows and other frames, wrought framed and fixed in position including SS expansion fastners for brick / concrete work in (/silver/marinda) as per the directions of Consultant/as per the drawings enclosed

Supply and fixing of 35-38 mm thick frame of Silver/Mirinda wood (Seasoned) paneled shutter with paneling of teak wood termite proof phenol bonded board with decorative teak veneering on both faces of suitable pattern including beadings lippingsetc fixing of wooden cleats, door stoppers and adjustment of anodized aluminum hinges, bolts, locks, handle, springs, etc. complete with all the fittings as per drawing and specifications. ( Rates to include cost of cleats, stoppers, hinges.

Providing and fixing 35 mm thick glazed panelled or panelled and glazed shutters (Kail Wood) for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: - Butt hinges and necessary screws shall be paid separately)

Providing and fixing wire gauze shutters Kail Wood using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing 5mm thick panels of plain glass for fixed glazing panels/ shutters (only panel area to be measured) including cost of teak wood beadings of required size complete

Providing and fixing Almunium hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications .

Modular door lock ss finish handle 10" with duaal locking system inside & outside (godrej)

Tower bolts 100mm (windows)

Handle 100mm (window)

I-Hooks 150mm

Tower bolts 150mm (doors)

Handle 125mm (door)

butt hinges of 100x63x3.2 mm

Painting with synthetic enamel paint of approved brand and manufacture excluding applying priming coat with ready mix pink of approved brand and manufacture on wood work etc. including cost and carriage of all materials equipments complete job as per drawings, specifications and as directed by the engineer Incharge.

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying cement based wall putty 2 mm of required thickness over plastered surface to prepare the surface even and smooth complete in specified areas as per specified patter. (Birla make) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

POP cornice in cielings 75mm wide with required thickness in specified areas as per specified pattern

Providing and fixing wadrobe shutters all shelves of laminated 19mm thick ply wood and all hardware like channels etc as per drawings and specifications.(Face Area)

Providing and fixingmodular kitchen cabinets 19mm water proof ply wood thick board above and below counter along with all hardware like channels etc as per drawings and specifications.(Face Area)

Granite Work in Floors :- Providing and fixing ( gang saw cut mirror polished (flamed , pre-moulded and pre-polished), machine cut for flooring, steps ,risers of stairs etc.( flamed instaircase) of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shape 18mm thick. and slab area over 0.50 sq m. (Note: The Granite stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc. upto site of work complete

Providing and fixing 1st quality Vitrified tiles in floor/skirting etc. of standard thickness of approved make in all colours, shades, design and prints as approved by the engineer-in-charge over 12 mm thick bed of cement mortar 1 : 3 (1cement 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg per Sqm. Including pointing in white cement mixed with pigment of matching shade with all lead, lift, labour, materials, tools, plants complete as per specification and as directed by Engineer in Charge . (600X600 mm)

Providing and fixing ist quality ceramic glazed tiles in floors ( thickness to be specified by the manufactures) confirming to IS: 13753 of approved make like NITCO, Orient, Somany, Kajaria or equivalent make of specified shades except Burgundy bottle green black of any size as approved by consultant over 12mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3Kgs per Sq.m including pointing in white cement mixed with pigment of matching shade complete (300mm x300 mm )

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 13753 of miniumum thickness 6 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA or equivalent make in all colours, shades except begundy, bottle green, black of any size as approved by the Engineer- in-Charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. sample to be approved by Engineer-in- charge. Size if Tile 250 x 350 mm. (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc.,by applying cemnet slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement@ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement compound @ 0.126 kg/sqm. This layer will be allowed t air cure for 4 hours followed with water curing of 48 hours. The rate includes preparation of surface, treatment and sealingof all joints ,ciorners, juntions of pipes and masonry with polymer mixed slurry.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.(Crushed)

French spirit polishing, Two or more coats on new works including a coat of wood filler.

Providing and fixing plannes eaves boarding (300mm x 40mm )( nominal size) second class kail wood fixed with screws etc, including all carraiges .All job completed.

Providing and fixing 20 mm thick wooden planks ceiling/ soffit(frame work for base to be paid for separately) with M.S. screws with imported/badloo wood.

Providing colour coated sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)including ridges /valleysexcluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.5 mm thick

Supplying and erecting welded steel work in built up sections in trusses/trussed purlins /beams/rafters up to desired span and height confirming to specified code including cost of priming coats.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gram/m

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. .5mm thick with zinc coating not less than 275 gram/m2.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position (Budloo / Fir Wood).

Providing and fixing dagi dewari as per local architectural heritage 100mm x 40mm wooden planks of ist class kailwood wood fixed horizontally, vertically, inclined with necessary screws, adhesive and other items ( Ist class kail wood).

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.50 mm thick with 20mm nominal size stone aggregate.

Providing and fixing glass strips in joints of terrazzo/ cement concrete floors.40 mm wide and 4 mm thick

Providing and Fixing of 50mm dia stainless steel railing of 304 grade of all complete job.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white PVC flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Under Counter wash basin,with 32 mm Waste Coupling and other allied accessories including cutting and making good the walls wherever required: White Vitreous China Under Counter Wash basin.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board, 600X450X250 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 600X450 mm

Providing and fixing toilet paper holder with Flap made out of C.P Bras

C.P Brass

Providing and fixing C.P Brass Soap Dish.

Providing and fixing health faucet with hose pipe for european water closet complete in all respect of approved quality as approved by Engineer I/C.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screw as approved by Engineer I/C.

Providing and fixing C.P brass bib cock long body ISI Make as approved by Engineer I/C. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality &make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.

75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B.

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.

Constructing masonary chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design With F.P Bricks.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms,lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Supply, Installation of PVC Gully Trap of Size 110mm as approved by Engineer I/C.

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 long complete as per standard design.

With F.P.S. bricks

Constructing septic tank, of size 6.60mx 2.20 mx1.80 m approx. height(Height to be fixed as per site requirement i.e. below invert level of last manhole (1.5 m water depth) , in B/W, 350/230 mm thick ( minimum) walls and 400 mm

50 mm Diameter

40 mm Diameter

32 mm Diameter

25 mm Diameter

Providing and fixing on wall 35 LTRS Electric Geyser with ABS Bo

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump(1HP ) with a Discharge of 100 LPM @Head of 35 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel.

Providing & fixing water closet squatting pan (Indian Type W.C pan) with 100mm P or S trap, 10 litre low level P.V.C flushing cistern including flush pipe manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: Orissa pattern white vitereous china W.C. Pan of size 580 X 440 mm with integral type foot rests.

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and making good the walls etc.: 15 mm dia. Nominal bore (Medium) make.

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and making good the walls etc.: 25 mm dia. Nominal bore (Medium) make.

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and making good the walls etc.: 32 mm dia. Nominal bore (Medium) make.

Providing and fixing gun metal Gate Valve with C.I. wheel of approved quality (screwed end): 32mm nominal bore

Providing and fixing ball valve (brass of approved quality complete: 20mm nominal bore

Providing and fixing15mm dia. Nominal bore Plasticized P.V.C. connection pipe with brass union 45 cms Length.

Providing and fixing C.P. Brass Shower Rose with 15 or 20 mm inlet. 150mm diameter

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in english with direction arrows

15mm nominal bore

25mm nominal bore

32mm nominal bore

Providing and fixing thermal insulation tubing (for hot water pipes chases/buried locations), elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of nominal bores and thickness including all required accessories complete as per specification. 15 mm/32 mm dia

Drainage:-

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil

Providing laying hand packed stone soiling including cost of all charges complete job

Mudmat:Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

entering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete:Thermo-Mechanically- Treated bars.

12 mm thick cement plaster in 1:4 cement mortar in walls using coarse sand.

Steel work welded in framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as requireIn gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Manufacturing supplying and fixing retro reflective sign boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type-IV of ASTM-D-4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC : 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20cm c/c to back support frame of 16.0 (Road Work) 224 CODE NO. DESCRIPTION UNIT RATE ₹ M.S. angle iron of size 25x25x3mm along with theft resistant measures mounted and fixed with 2 nos. M.S. angles of size 35x35x5mm to a vertical post made upto M.S. Tee section ISMT 50x50x6mm welded with base plate of size 100x100x5mm at the bottom end and including making holes in pipes, angle flats, providing and fixing M.S. message plate of required size steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical M.S.-Tee support to be painted in black and white colours). Backside of aluminum sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coats including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge. 16.66.1 Mandatory/Regulatory sign boards 900mm

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. 300 mm dia. R.C.C. pipe

Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 12.7.1 0.8 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes a) 75 mm diametre including all fittings / accessiries

110 diametre

Road Work:-

Earthwork in cutting to form road section in correct profile including removal of spoils not exceeding initial lead of 50m and initial lift of 1.50m

P/L granular sub base couarse not less than 90mm size boulders including dressing ramming watering and consolidation with power road 8-10 tone capacity including all carriage to site of work by MT nallah muck

P/L and supplying by manual means and compacting stone agg of size 63-45mm crushed stone agg from quarry metal to water bound macadam specification including spreading in uniform thickness hand packing, rolling with smooth wheel roller 80-100KN in stage to proper grade and camber, applying and brooming stone screening, binding material to fill up the interstices of course agg. water and compacting to required density grade-II as per (MORTH) specifcation including cost and carriage of all involved material

P/F of G.I chain link fabric fencing of required width in mesh size 25X25 mm made of G./I wire of dia 3 mm including strengthening with 2 mm dia wore or nuts, bolts & washers as required complete as per the directions of Engineer I/C.

Providing and placing in position 100mm thick factory made machine batched and machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage ,all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). 16.67.1 Overhead informatory road signage.

Cast in situ of concrete of nominal mix concrete M10 grade nominal maximum size of stone aggregate 40 mm volumetric batting up to plinth level.

Providing and laying at or near ground level factory made kerb stone of M25 grade cement in position to the required line,curvature and level jointed with cement mortar 1:3(1 cement :3 coarse sand ).including making joints with or without grooves(thickness of joints should not be more than 5mm except sharp curves)including making drainage opening wherever required complete etc as per direction of engineer incharge .

Providing Centering and shuttering ,propping and removal of formwork .

12 mm thick cement plaster in 1:6cement mortar in walls using coarse sand.

Painting kerb stone with adequete no. Of coats to give uniform finish with paint of superior paint make as approved by engineer incharge including cleaning the surface of all dirt,scales,oil,grease and other foreign material of new works(two or more coats)

Providing and laying 60mm thick factory made cement concrete interlocking paver blocks of M30 grade made by block making machine with strong vibratory compaction and of approved size and design laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand filling the joints with coarse sand complete job.

Earth work excavation in foundation trenches ,incl. dewatering of foundation trenches excavation of work.

Providing and laying of hand packed stone soling (size 150mm-230mm) before laying of mud mat compacted consolidated rammed filling the voids compacting all complete carriage upto site of work all head loads complete job.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Supplying, filling with river sand /nallah muck in 20 cm layers including watering, compacting and dressing under flooring in ground floor.

Providing and laying of 50mm thick concrete flooring in rooms in M-15 (1:2:4) nominal mix(max.size of aggregate 20mm) concrete finished with floating coat of neat cement.

Providing Centering and shuttering ,propping and removal of formwork .

M20 : Reinforced Cement Concrete P/L of Reinforced Cement Concrete of Nominal mix M20 1:1.5:3 Up to Plinth Level

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete:Thermo-Mechanically- Treated bars.

12 mm thick cement plaster in 1:4 cement mortar in walls using coarse sand.

Construction of concrete manhole with C.I cover including cost of all materials.

Providing and Laying of Random rubble stone masonary using nallah stones with bond stones in foundation & plinth dry.

Providing and Laying of Random rubble stone masonary using quarry stones with bond stones in foundation & plinth including levelling up with cement concrete 1:6:12 (1 cement:6 coarse sand :12 graded stone aggregate 20mm N/S) with 1:6 mix.

Steel structural work with mild steel of small sizes and sections such as holding down bolts hold fast tie rods gratings MS grill etc. wrought to required form including supply of steel and its wastage including cost of bolts, nuts, if required for and welding grinding and making holes as required completion of work fabrication of holes nosing.

P/F and commisioning 1H.P water PUMP

P/F of Aluminum composite panel in pillars etc including cost of frame work {tubes 25X25 mm} including cost of all charges completed job(3 to4mm thick).

Cleaning/ levelling of site

Parking:-

Earthwork in excavation by manual means over areas (exceeding 30 cm and upto 1.5mtr depth in depth , 1.5 mtr in width as weel as 10sqm on plan) including disposal of excavated earth upto 1 mtr from cutting edge,disposed earth to be levelled and neatly dressed in all kinds of soils.

Providing and laying of hand packed stone soling (size 150mm-230mm) before laying of mud mat compacted consolidated rammed filling the voids compacting all complete carriage upto site of work all head loads complete job.

Mudmat : Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

PCC: Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering .1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting, proping etc. And removal of form for:Foundation, footing bases of columns etc for mass concrete.

Providing and fixing of fencing of MS grill of variable sctions and design vertical and horizontals as per design,inluding the cost of fixtures fittings.priming coat and two or more coats of painiting including the cost of screws /bolts complete job

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) above plinth level upto floor five level

Providing ,laying , spreading and mixong of good earth at site including royalty and carraige complete job

12mm Cement Plaster in mix 1:6(1 cement : 6coarse sand) on external walls

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm

Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coat

M/S Farooq Ahmad Dar

M/S MOHD YOUSUF RATHER

MANZOOR AHMAD BHAT