mm

mm

Screw driver - 150mm insulated flat type

Chisel cold flat - 20 mm x 150 mm High carbon steel

Hammer ball peen with handle - 450 grams 1 lb

Hammer ball peen with handle. - 220 grams 1 by 2 lb

File flat - second cut - 250 mm

File flat smooth - 250 mm.

File half round second cut - 150 mm.

Hacksaw frame fixed type - 300 mm

Safety goggles.

Dot punch - 100 mm

Spirit Level metal Type - 2 - 300 mm Basic Length Accuracy 0.1mm per Meter

Stud Extractor EZY - out - Set of 8

Combination Set - 300 mm

Micrometer outside. - 0 - 25 mm

Micrometer outside. - 25 - 50 mm

Micrometer outside. - 50 - 75 mm

Vernier caliper - 150 mm

Screw pitch gauge Metric - 0.25 to 6 mm

Wire gauge

metric standard.

Angle plate - 150 x 150 x 250 mm

Punch letter set. - 3 mm

Punch number set. - 3 mm

Drill twist straight shank - 3 mm to 12 mm by 0.5 mm H.S.S.

Drill twist Taper shank - 8 mm to 20 mm by 0.5 mm H.S.S.

Taps and dies complete set in box. - Whitworth

Taps and dies complete set - 5

6

8

10 12mm set of 5

File knife edge smooth - 150 mm

File feather edge smooth - 150 mm

Feeler gauge - Gauge Feeler Thickness 0.05 mm to 0.3 mm by 0.05 and 0.4 mm to 1 mm

File flat second cut safe edge. - 300 mm

File flat bastard. - 300 mm

File Swiss type needle - Set of 12

Length 150 mm

File half round second cut. - 250 mm

File half round bastard. - 250 mm

File round bastard. - 250 mm

File card. - 3x5 size

brass or steel wire

Oil Can - 250 ml

Pliers combination insulated - 150 mm

Wooden handle forged Soldering Iron copper bit. - 230V

250 W

350 gm

Blow Lamp - 0.5 litre

Spanner- Double Ended - 6x7

Interchangeable ratchet socket set - 12 mm driver

sized10-32 mm set of 18 socket attachments.

Double Ended tubular Box spanner set with Tommy bar

Glass magnifying - 75 mm

Clamp toolmaker - 5 cm and 7.5 cm set of 2.

Clamp C - 200 mm

Hand Reamer set Taper pin straight flute - Nominal Dia. 6

10

12

16mm

Machine Reamer parallel Helical flute - 12 - 16mm set of 5.

Scraper flat - 150 mm

Scraper triangular - 150 mm

Scraper half round - 150 mm

Chisel cold crosscut diamond point. - 9 mm x 150 mm

Chisel cold flat - 9 mm x 100 mm

Chisel cold round nose - 9 mm x 100 mm

Pipe vice - 100 mm

Wheel dresser One for 4 units Star or Dresser with Holder - Length 150 mm

diamond point

Sleeve drill Morse No. 0 to 1

1 to 2

2 to 3

3 to 4

4 to 5

Vice bench - 150 mm

Wing compass. - 254 mm or 300 mm

Hand hammer with handle. - 1000 gm

Torque wrench Standard or Ratchet type - 14 to 68 Nm

Temperature gauge - Range 0 to 150 degree Celcius

Standard Tap screws - M3

M4

M5

M6

M8

M10

M12

M14

M16

Caps screws - M6

C.I. Sluice or Gate valve flanged type 150NB

Stop cock - 25NB 2 way

Threaded end

Slip-on Forged steel Flange - 150NB

Bolt Nut with washer May be manufactured in house M20x 2.5x 90

Pulleys for V-belt or Flat belt - to fit on 50mm dia. Shaft with key slot

Steel keys May be manufactured in- house - to fit with key slot of shaft pulley

V-belt and Flat belt - to fit on pulley

Packing gasket - PTFE gasket roll small size

Washer

clutch

keys

jib

cotter circlip - minimum 25mm size

carbon steel material

Hollow punch - Straight Shank Hollow Punch Sets 5-12mm

Drill Drift May be manufactured in- house - 200mm hardened and black finish

Bearing different types - each type of diameter 25mm min.

Lifting sling - 8mm Nominal Dia. Single leg sling

Bearing extractor - Universal gear puller 2 or 3 jaws adjustable

Pulley extractor

Trammel - 300 mm

Pocker

Prick punch - 100 mm

Mallet. - Dia. 100 mm x 150 mm

Aviation Snips straight Cut - 300 mm

Flat headed hammers with handle.

Planishing hammer.

Snip bent Left Cut - 250 mm

Gauge snap Go and Not Go 25 to 50 mm by 5