GE / SHL / 06 OF 2020-21

Amount

Surface dressing n.exc 15 cm deep in soft / loose soil etc complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in soft/loose soil and getting out complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M&L for PCC (1:4:8), type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete 1:3:6 type C1, using 20 mm graded stone aggregate, exc 10 Cm width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n.exc 63mm deposited , spread and well levelled in layers not exc 15 cm thick water, rammed to a true surfaces etc complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 ( using 40 mm graded stone aggregate) 75 mm thick as in sub base of floor , finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1 ( nominal mix) (using 20mm graded crushed stone aggregates ) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1 ( nominal mix) (using 20mm graded crushed stone aggregates ) as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1 ( nominal mix) ( using 20mm graded crushed stone aggregates ) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1 ( nominal mix) ( using 20mm graded crushed stone aggregates ) as in slabs supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and as directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc etc complete all as specified and as directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and as directed.

M&L for rendering 10mm thick in cement sand mortar 1:6 on fair faces of brick Walls or on concrete surface,finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a coat of 10 mm thick base coat complete all as specified and as directed by Engineer-in-Charge. Note WPC shall be measured and paid separately.

M&L for 5mm thick cement plaster in cement sand mortar (1:3) on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) as in plinth protection , finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:6 complete all as specified and as directed.

M&L for Glazed ceramic Coloured tiles of size 450 mm x 300 mm x7mm thick as in vertical surfaces such as Skirting, dados, etc.set and Jointed in neat cement slurry and pointed in white or colour cement to match laid over and including a backing coat of 10mm thick screed bed in cement sand mortar 1:4 etc complete all as specified and as directed.

S&F Vitreous china squatting pan of Orissa Pattern of size 580x 440 mm ,white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( using 40 mm graded crushed stone aggregates), 1:5:10 and finishing the top surfaces to match with the existing flooring complete all as specified and as directed .Make:- Prayag cat part no. 4055 or equivalent make of Pearl / Hindware.

S&F PVC (Plastic polymer flushing Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge .Make:- Prayag cat part no. 503 or equivalent make of Parryware / Hindware.

S&F Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat part no. 4645 IRIS or equivalent make of Parryware / Hindware.

S&F Bib tap 15 mm bore, PTMT , any colour high pressure screwed for iron pipe ( minimum weight 90 gms) etc complete all as specified and as directed. . Make:- Make:- Prayag / Sona / Hindware.

S&F stop valve 15 mm bore, PTMT , any colour high pressure screwed for iron pipe ( minimum weight 90 gms) etc complete all as specified and as directed. . Make:- Make:- Prayag / Sona / Hindware.

M&L for 2nd class hard wood as in plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and as directed.

S&F 2nd class hardwood glazed and skeleton shutters 35mm thick ,open rebated and prepared to receive galss, glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded. fitting with cut and mited beads for securing glass, etc, size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) supplied and fitted to chowkats etc complete all as specified and as directed.

S&F MS butt hinges, medium weight 100mm, cold rolled and fixed with stainless screws etc complete all as specified and as directed.

S&F mild steel barrel tower bolts stove enemelled black with bright bolt ISI marked 200 mm length complete all as specified and as directed.

S&F Mild steel pressed handles, oval type, stove enamelled black ISI marked 150 mm length complete all as specified and as directed.

S&F sheet glass 3 mm thick, ordinary quality and glazed with oil putty in square n.exc. 0.5 sqm in each pane including fixed with wooden beads / glazing pins or spring clips in wooden or metal frames etc complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S & F 110 mm bore PVC (SWR) bend of any radius complete all as specified and directed.Make:- Prince / Supreme.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.Make:- Prince / Supreme.

S&F GI tubing 15mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F GI tubing 20 mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F Rotational moulded HDPE polyethylene 1000 ltrs capacity water storage tanks three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20 mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20 mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F Cast iron floor trap, diameter of outlet in 75 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) ( using 20 mm graded stone aggregate) etc complete all as specified and directed.

S&F factory made pre laminated solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I complete all as specified and directed

S&F Solid PVC door frame of size 50 mm X 47 mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, etc complete all as specified and as directed .

S&F Allumunium, handles 150mm, cast type anodised. fixed with anodised screws etc complete all as specified and as directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed. etc complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer etc compete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wall including cornices, plasters etc and applying two coats of white wash including necessary preparation etc complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of ceiling and applying two coats of white wash including necessary preparation etc complete all as specified and as directed.

Supply only integral water proofing compound, ISI marked.complete all as specified and as directed.

M&L for Framed MS work such as grills, gratings, etc.. with ends of bars shouldered and /or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

Taking down shutters of any description n. exc. 1 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm each and removing from site complete all as specified and directed.

S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides .etc complete all as specified and as directed.

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed , 75 mm size etc complete all as specified and as directed.

S&F Mild steel pressed handles, oval type, stove enamelled black 100 mm size etc complete all as specified and as directed.

S&F Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed 100 mm size etc complete all as specified and as directed.

S&F Mild steel sliding door bolts, 250 mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed etc complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, 140 mm long , anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed.

S&F sheet glass 4 mm thick, ordinary quality and glazed with oil putty in square exc. 0.5 sqm in each pane fixed to wooden / metalic / frame etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) (using 20mm graded crushed stone aggregates ) as in Chajjas etc complete all as specified and as directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges etc complete all as specified and as directed.

M&L for preparation of newly or previously untreated surfaces of wall and applying two finishing coats of oil bound distemper of approved shade / tint ,over a coat of alkaline resistant primer including and over a thin layer of wall care putty to achieve smooth etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of white or tinned with cement base paint over and including a coat of wall primer etc complete all as specified and directed.

Cutting holes in brick walls built, in cement mortar or cement lime mortar , size exc 150 sqcm but n.exc. 400 sqcm and making good to disturbed surface in cement sand mortar 1:3 or cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as required etc complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-1 ( using 20 mm graded stone aggregate ) as in fixing of holdfast / metallic post in wall or floor etc complete all as specified and as directed.

Cutting chases, pinning in stone concrete blocks or concrete walls. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth etc complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded etc complete all as specified and directed.

S&F Non asbestos fibre cement building boards manufactured from homogeneous mixture of cement , quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862 of size 600 mm x 600 mm x 4 mm thick fixed over and including anodised aluminium powder coated ( minimum thickness of powder coating 50 micron) snap grid frame work of T section ( main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 600 mm x 600 mm .The aluminium frame work shall be supported on side wall with using aluminium L section of size 25 mm x 25 mm x 1.5 mm angle.Snap grid shall be supported with GI hangers of 4 mm dia . Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling GI flat iron cleats of size 40 x 3 mm and 60 mm long expansion hold fasteners 12.5 mm dia 40 mm long etc complete all as specified and as per directions of Engineer-in-charge.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out of soft / loose soil etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) (using 20mm graded crushed stone aggregates ) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) ( using 20mm graded crushed stone aggregates ) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) ( using 20mm graded crushed stone aggregates ) as in Column, pillars, piers, posts, posts and struts etc complete all as specified and as directed.

M&L for rendering 10 mm thick cement plaster in cement sand mortar (1:6) on brick or stone masonary surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for preparation of new or previously untreated surfaces of wall including cornices, plasters etc and applying three coats of white wash including necessary preparation etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B-2 ( using 20 mm graded stone aggregate) 100 mm thick ,as in floor , finishing even and smooth with using extra cement etc complete all as specified and as directed.

M&L for Mild Steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 etc complete all as specified and as directed.

M&L for Mild Steel work as in Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections etc complete all as specified and as directed.

M&L for Painting two coats of Synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surfaces of any description, over 10 cm width or girth including preparation of surfaces etc complete all as specified and as directed

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strngth of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour etc complete all as specified and as directed

M&L for Moorum / red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and as directed.

M&L for Walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in cement sand mortar 1:6 etc complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses maximum depression on face from straight edge held against the dressed surface n exc.20 mm granite or trap stone etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in coping over RR wall including necessary formwork etc complete all as specified and directed.

M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement sand mortar 1:4 etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 ( using 20 mm graded stone aggregate) as in bond stones set in cement sand mortar (1:6) including necessary formwork etc complete all as specified and as directed.

S&F pre-painted Galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick having tensile strngth of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour etc complete all as specified and as directed

M&L for machine pressed pre polished factory made chequered cement concrete tile with grey cement and pigment ( of approved tint ) of size 30 cm x 30 cm x 25 mm thick of approved design and colour over and including 15 mm thick screed bed in cement sand mortar 1:6 , set , jointed and pointed in neat cement slurry etc complete all as specified and as directed

Excavating over areas n.exceeding 1.5 m depth and getting out loose excavated soil in loose / soft soil etc complete all as specified and as directed

M&L for PCC 1:4:8 type D-2 ( using 40 mm graded stone aggregate) 100 mm thick ,as in sub base , finishing even and smooth with using extra cement etc complete all as specified and as directed.

M&L for rendering 10 mm thick in cement sand mortar 1:4 on fair faces of brick Walls or on concrete surface,finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for rendering 15 mm thick in cement sand mortar 1:4 on fair faces of brick Walls or on concrete surface,finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for Point wiring with two single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked), green colour as continuous earth wire terminated connected to common earth dolly for one light / fan point controlled by one way switch including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge .Make of cable:- KEI / RR Kabel / Havells . PVC Casing & Capping:- Prestoplast / Finolex / Kalinga

All as per item No 93.00 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as directed by Engineer -in -Charge .

All as per Item No. 93.00 here-in-above but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.00 sqmm green in colour as earth continuity conductor connected to common earth dolly in PVC casing caping complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, one way 5/6 Amps complete all as specified and directed.

Supply and fix switch socket combination (ISI marked), 2/3 pin and 5 Amps, 240 volts , flush type complete all as specified and as directed.

Supply and fix switch socket combination (ISI marked), 2/3 pin and 15 Amps,240 volts complete all as specified and as directed.

S&F in repair Decorative wall mounted LED batten fittings with all accessories, 1X18 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed. Make Havells Cat part No. LHEXBQP71N1W018 or Make:- CROMPTON Cat Part No. LCTL 18 CDL.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

Supply and fix MCB SPN, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Havells cat part no. DHMGCSPF006-32 or equivalent make in Legrand / L&T.

Supply and fix MCB SP, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Havells cat part no. DHMGCSPF006-32 or equivalent make in Legrand / L&T.

Material and labour for sub main wiring with two single core 4.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 4.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed.(Note: two run of 4.0 sqmm cable , one run of earth wire of 4.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- KEI / RR Kabel / Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Supply and fix MCB Distribution board , 240 volts ,SPN ,single door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link,4 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer -in- Charge. Make : Havells cat part no. DHDPSHODRW04 or equivalent make in Legrand / L&T.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sqmm nominal cross section in service connections etc complete all as specified and as directed.

S&F New generation, energy saving and enviormental friendly, long life versetile pressure diecast aluminium IP 66 roadway luminaire 25 w LED with bracket and all necessary accessories etc complete all as specified and as directed.Make:- Bajaj cat part no. BRLEP 25 W LED WH or equivalent make in Philips / CG.

M/S UTTAM SAHA