Infrastructure work like Interior,furniture etc. for stablishment of National health mission Office in Mandi Parishad New Building(G plus 4) at 16,A.P. SEN Road, Lucknow.

Amount

Providing & Fixing of at all height false ceiling including providing and fixing of frame made of special section power pressed from m.s. sheet and galvonised in accordance with zinc coating of grade 350 as per IS 277 and consisting of angle cleat 25x1.6mm with flanges of 27mm and 37mm at 1200mm c/c one flanged fix to the ceiling with dash fastener 12.5mm dia and and 40mm long with 6mm dia bolt to the angle hangers of 25x25x0.55 mm of required lengthened other end of angle hanger being fixed with nut and bolts to GI channel 45x15x0.90mm running at the rate of 1200 mm c/c to with the ceiling section 0.5mm thick button wedges of 80mm with tappered flenges of 26 mm each having clips of 10.5mm.at 450mmc/ c shall be fixed in direction perpendicular to GI channels with connecting clips made out of 2.64MM diax230mm long GI wire at every junction including fixing the gypsum board with ceiling section and perimetre channels 0.50 mm thick 27mm high having flenges of 20mm and 30mm long ,perimeter of ceiling fixed to wall /partition with help of rawl plugs at 450mm c/c with 25 mm long drive all screws @230mm interval including jointing and fixing to a flush finish of tappered end sq edge of board with recommended filler jointing and tapper finisher and two coat of primer suitable for board as per manufacturers specification and also including the cost of making of openning for light fittings grills diffusers cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of engineer incharge but excluding the cost of painting.12.50mm thick tapered edge gypsum moisture resistant board.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) heet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false eiling tiles of approved texture in the grid including, required utting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI SUB HEAD : 12- ROOFING 878 adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all Tsections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. Armstrong MAke-Classic Lite RH-99. or equivalent

Providing and fixing of 8 mm thick Laminated wooden flooring Classification of Use 23/32 (Heavy Domestic/General Commercial) with a Surface Abrasion Resistance of class AC4 (average 4500 cycles), Impact Resistance of IC2 (EN13329), Resistance to Cigarette Burn with a rating of 5 (EN 438-2:15), Swelling after 24 hrs in water of 15% (EN13329), Modulus of Rupture of 53.3 newton/mm2, Internal Bond 1.78 newton/mm2, Surface Soundness of 1.3 newton/mm2 (EN 13329:2000) with a 0.2mm thick wear layer on top of a High Density Fiber substrate core (density > 850 Kg/M3) of plank size 1291 mm X 193 mm having Uni fit locking arrangement (lock strength > 1000 lbs/ft) with an underlayment made of natural colour foam , with accessories like End profile, Transition profile, reducer, etc. complete. The rate includes cost of all materials, accessories, labour, HOM, etc., complete at all levels. (The Shade, pattern etc., to be approved by Engineer in charge)Make-Egger/FloorMaster/Haro/Armstrong/Luxe.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick no tile adhesive (water based) onforming to IS: 15477, in average 6 mm thickness, including grouting of joints. Size of Tile 600x600 mm.

Providing & Making & Fixing of Commercial Wall Panneling made with Aluminium Section of 2"x1" @ 2'CC frame work cladded with 12MM Ply complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Making & Fixing of Wall Panneling made with Aluminium Section of 2"x1" @ 2'CC frame work cladded with 12MM Ply & Finished with 1MM Laminate complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Making & Fixing of Wall Panneling made with Aluminium Section of 2"x1" @ 2'CC frame work cladded with 12MM Ply & Finished with 4MM Veneer complete with Melamine Polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Making & Fixing All height partitions made with Aluminium Section of 1.75"x1.75" @ 2'CC section frame work cladded with 9mm Ply on Both Side & final Surface to be finished with 1MM Laminate complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Making & Fixing All height partitions made with Aluminium Section of 1.75"x1.75" @ 2'CC section frame work cladded with 9mm Ply on Both Side & final Surface to be finished with 4MM Veneer complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Making & Fixing All height partitions made with Aluminium Section of 1.75"x1.75" @ 2'CC section frame work cladded with 9mm Ply on Both Side & Front side Surface to be finished with 12MM Louvers & Back Side with 1MM Laminate complete with painted or polished. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing and fixing aluminium work for doors, windows and ventilators with extruded built up standard tubular sections or other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required Including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Pre-laminated particle board with decorative lamination on both sides on Bottom Partition Member & float glass panes of 5 mm thickness above Mid Partition Member) : powder coated 2 mm thick aluminium section (minimum thickness of powder coating 50 micron). Make Hindalco or equivalent as per E/I.

Providing and fixing aluminium work for partitions with extruded built up standard tubular sections or other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required Including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Pre-laminated particle board with decorative lamination on both sides on Bottom Partition Member & float glass panes of 5 mm thickness above Mid Partition Member) : powder coated 2 mm or as required thick aluminium section (minimum thickness of powder coating 50 micron).Make Hindalco or equivalent as per E/I.

Providing and Fixing Channeled Woodworks perforated panels of width 128mm, thickness of 16mm and length 2440 mm or as required by the Architect/ approving engineer, made of a high density particle board substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a (“Helmholtz” fluted perforation of 2mm width and 14mm of visible panel / 4mm width and 28mm visible panel) each. The panels shall provide a minimum sag resistance of RH90 and a fire rating class of 1 as per Part 7 of BS 476. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece. The panels shall be mounted on special aluminium splines using clips. as per the approved design as approved by Engineer -in-Charge.

Providing and supplying ‘Optra Acoustical Wall Paneling’ with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and fire -resistant fabric with an option of colours as per the choice of the Architect/ Person in-charge of size 1200x600 or 600x600 mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using Wall panel impalers and construction adhesives as per the instructions laid down by the manufacturer as per the approved design as approved by Engineer -in-Charge.

Providing & fixing of 12 mm Toughened Glass Door with all hardware as per design with edge polish m/c top & bottom pivot and bottom lock with handle all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & fixing of Flush Door Laminated both side complete with all fittings,Round mortis lock,door closer etc all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Fixing of Roller Blinds of approved shade as per drawing & specification as approved by Engineer -in-Charge.

Providing & Fixing of Plotter Cutted Designer Film of approved shade as per drawing & specification as approved by Engineer -in-Charge.

Providing & Fixing of Wall Paper of approved shade as per drawing & specification as approved by Engineer -in-Charge.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing & applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer.

Providing & Fixing of Cupboard at all niches below sill level on all peripherel walls on all floors except first floor with ACP Sliders all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & Fixing of Cement BoardRacks in File Storage area of 2.4 Mtr(Ht) x 0.45 Mtr(Depth) of Total Wall Area on All Floors all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Brick work Class-150 brick work in 1:4 cement and coarse sand mortar in super-structure including necessary cutting and molding of brick work as required and also including honey combed brick work in thickness of wall one brick thick complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry complete as per direction of Engineer in Charge

12 mm. thick plaster with 1:4 cement and coarse sand mortar in single coat on any side single or half brick wall and finished even and smooth. including supply of all material labour T&P etc complete as per direction E/I

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia.

Providing and laying rectified Glazed Ceramic Wall tiles of size 600x300mm or more (thickness10mm of premium quality conforming to IS : 15622/2006, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 12 mm thick cement mortar 1:3 (1 Cement: 3 Coarse sand), morter including grouting etc. complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm. as per direction of E/I

Providing and fixing of 110mm dia pipe UPVC Pipe of Supreme make or equivalent, including supply of all materials, labour and T&P etc.

Providing and fixing white vitreous china extended wall mounting water clono of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. S.I. NO.17.78/2020

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. S.I. NO.17.7.2/2020

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. S.I. NO.17.8/2020

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore S.I. NO.18.50.1/2020

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. S.I. NO.17.16A/2020

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore S.I. NO.18.53.1/2020

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. DSR(17.22A)/2018 LESS GST

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. DSR(17.72)/2018 LESS GST

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore DSR(18.21.1.1)/2018 LESS GST

Providing & fixing Health Faucet as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Jaquar/American Standard/Kerovit Eqivalent.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm Aligarh SOR (2020)

Providing & fixing of Wall Mounted Sink Cock With Swivel Spout & Flange as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Jaquar/American Standard/Kerovit Eqivalent AR

Wiring point for light with 1.5 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq.mm. FRLSH copper earth contunity wire,modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash.

Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq.mm. FRLSH copper earth contunity wire,modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash.

Supply and fixing of power plug with 20A/250 V flush type modular switch and 5 Pin 20 A/250 Volt flush type universal modular socket switch on concealed M.S. box including supply of all material, labour T & P etc required for proper completion of work.

Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer.

Wiring point for Call Bell with 1.5 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq.mm. FRLSH copper earth contunity wire,modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash. S.I 125(B)+187(E)

Supply and wiring of submain with two number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 number 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor as earth continuity wire.

Providing Drawing Connecting And Testing Of Enhanced Categoey 4 Pair Lan Local Area Network Cable 24 AWG Conductor Performance Specifide 5E U L and CUL Listed In Existing PVC Conduit .(CAT-6 Network Cable).

Supplying & Fixing Of Telephone Wire 2Pair 0.5Sqmm solid conductor, PE insulated shielded with fine finned copper braid and protected with PVC sheath in the existing surface/ recessed steel/PVC conduit as required.

Supplying & Drawing co-axial TV cable RG-6 grade, 0.7 mm. solid copper conductor, PE insulated] shielded with fine finned copper braid and protected with PVC sheath in the existing surface/ recessed steel/PVC conduit as required. For T.V. Socket outlet.

Supply fixing and concealing of 20mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work. asdirected at site by the engineer in charge.

Supply fixing and concealing of 25mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work. asdirected at site by the engineer in charge.

Supply fixing and concealing of 32mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work. asdirected at site by the engineer in charge.

Supply and fixing of recess mounting round 15 mm 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver no complete in all respect. CAT-AAA.

Supply and fixing of 36 Watt to 46 Watt above 3300 leumin indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver no complete in all respect. CAT-AAA.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 50 sq. mm 3-1/2 core.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 70 sq. mm 3-1/2 core.

Supply and fixing of 6Amp to 32Amp SPMCB (10KA) C Curve CAT-A4 Pole Isolator CAT-A.

Supply and fixing of 63Amp 4 Pole Isolator CAT-A.

Supply and fixing of 100Amp 4 Pole Isolator CAT-A.

Supply and fixing of surface/Flush mounting 12ways TPN distribution board with additional metal door without MCB complete in all respect,as directed at site by Engineer in charge. CAT-A.

Supply and fixing of surface/Flush mounting 12ways V TPN distribution board with additional Door without DPX3 160 MCCB complete in all respect, as directed at site by Engineer in charge. CAT-A.

Supply & Fixing Blank plate for modular plate type switch boards wherever required.

Supply & Fixing of LED Strip Light all complete as per drawing and specification and direction of engineer incharge. Make-Klite, Havells,Philips Equivalent.

Supply & Fixing of LED Strip Driver all complete as per drawing and specification and direction of engineer incharge. Make-Klite, Havells,Philips or as approved

Supply and fixing of 400mm Wall Fan all complete as per drawing and specification and direction of engineer incharge. Make-Klite, Havells,Philips or as approved

Supply and fixing of 150mm Fresh Air Fan all complete as per drawing and specification and direction of engineer incharge. Make-Klite, Havells,Philips or as approved

Supply & Fixing of 24Port Switch all complete as per drawing and specification and direction of engineer incharge. Make-D-Link/Equivalent or as approved

Supply & Fixing of 24Port Patch Pannel all complete as per drawing and specification and direction of engineer incharge. Make-D-Link/Equivalent or as approved

Supply & Fixing of 4U Rack all complete as per drawing and specification and direction of engineer incharge. Make-D-Link/Equivalent or as approved

Providing & Fixing of Modular plate type white RJ 45 CAT 6 Data/Talephone outlet / information outlets ETL verified to meet or exceed TIA / EIA category 6 requirements, universal wiring label permitting to either T568A or T568B, UL listed, for computer networking complete in all respect with cover plate, grid plate, screws, MS box, etc with connections as required with 2nos RJ-45 Data outlet.

Supply and Fixing of recess mounting round 12 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver no complete in all respect. Make-Philips/Equivalent

Supply & Fixing of Hanging Light all complete as per drawing and specification and direction of engineer incharge. Make-Klite, Havells,Philips or as approved

Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick ) PVC conduit with one nomber 2.5 Sqmm FRLS PVC insulated multistrand copper condutor cable as earth continuity wire drawn in conduit. complete in all respect.

Supply and wiring of 4 number 10 sq.mm. FRLSH PVC insulated 1100V grade multistrand single core copper conductor cable in 32mm dia PVC conduit concealed in wall, with two number 6 Sqmm FRLSH PVC insulated copper condutor cable as earth continuity wire drawn in conduit complete in all respect.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 Sqmm 4 core

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 25 Sqmm 3.5 core

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire Damper

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuator

Supply, Laying, Testing & Commissioning of cooper conductor XLPE insulated armoued Power cable of following sizes complete in all respect. 3.5 C x 25 sqmm

Supply, Laying, Testing & Commissioning of cooper conductor XLPE insulated armoued Power cable of following sizes complete in all respect. 4C x 16 sqmm

Supply, Laying, Testing & Commissioning of cooper conductor XLPE insulated armoued Power cable of following sizes complete in all respect. 4C x 10 sqmm

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer- Incharge. 3.5 C x 25 sqmm

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer- Incharge. 4C x 16 sqmm

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer- Incharge. 4C x 10 sqmm

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 25 sqmm

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 16 sqmm

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 10 sqmm

Supply and burring of Safe Earthing Electrode T-39 Zn- Zinc Coated, Length 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonry housing. (From electrode terminal to switch board, cost of 25 x 3 G.I. Strip will be extra)

Supply and burring of Safe Earthing Electrode T-39 Cu Copper Coated, Length up to 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonry housing. (From electrode terminal to switch board, cost of 25 x 3 Copper Strip will be extra).

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 200 mm x 50 mm x 1.6 mm

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm x 50 mm x 1.6 mm

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm x 62.5 mm x 2 mm

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 600 mm x 62.5 mm x 2 mm

Supply, Installation, Testing & Commissioning of Hi Wall Unit 0.66 TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Hi Wall Unit 0.85 TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Hi Wall Unit 1.06 TR+Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Hi Wall Unit 1.65 TR + Corded reomte, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Hi Wall Unit 2.08 TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Round flow Casnote Unit 2.08 TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Round flow Casnote Unit 2.65TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Round flow Casnote Unit 3.31 TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Round flow Casnote Unit 4.13TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Round flow Casnote Unit 4.63TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Ductable Unit 5.66 TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Ductable Unit 6.66TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Ductable Unit 8.24TR + Corded remote, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply, Installation, Testing & Commissioning of Outdoor connecting kit, Make-Daikin, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 34.9 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 28.6 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 22.2 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 19.1 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 15.9 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 12.7 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 9.5 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each no of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 6.4 mm, all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Laying of M S Slotted Angle for pipes and cables horizontaly and vertically along with threaded rod, nut, bolt, saddle, tie etc, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing and fixing rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation. 25 mm dia, , as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing and fixing rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation. 32 mm dia, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing & fixing control cum transmission wiring of 2 core x 1.5 sqmm copper in suitable conduits between indoor and out door unit., as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation of Un-Insulated Square/ Rectangular “GSS” Supply Air Ducting As Per The Approved Shop Drawings. 24 Gauge, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation of Un-Insulated Square/ Rectangular “GSS” Supply Air Ducting As Per The Approved Shop Drawings. 22 Gauge, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation Of Thermal Insulation Over The Duct With Xlpe Sheet For The Ducts With 6 Mm Thick One Layer Externally On The Duct, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation Of Acoustic Lining Of Duct With 25 Mm Thick Fiber Glass Covered With Tissue Paper, Fly Mesh, Gi Screws And Washers., as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation Of Extruded Aluminum Powder Coated Supply Air/Return Air Linear Grilles, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation Of Volume Control Damper, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation Of Canvass Connection For VRV Ductable Type Indoor Units, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Supply & Installation Of Air Filters, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Wiring For Circuit/ Submain Wiring Alongwith Earth Wire With The Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable In Surface/ Recessed Steel Conduit As Required. 4 X 10 Sq. Mm + 2 X 6 Sq. Mm Earth Wire, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.

Providing and Fixing of Executive Wooden Table of Size (3600Lx1200Wx750HT) MM & Having 2 Nos Side Storage of Size (1200Lx450Wx700HT) Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge. Customized

Supply & Installation of Executive Table, PLPB Top, Flaper Box, Extruded Aluminium Profile (2400x2100x750), Model-Evoke-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Executive Table, Particle Board Top, (2200x1950x750), Model-Exclusive-2, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Executive Table, Particle Board Top, (1950x2000x750), Model-Numero-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Executive Table, Particle Board Top, (1500x1650x750), Model-Numero-8, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Workstation Table, Panel Based Partition, Particle Board Edge Banded Top, (1200x600), Model-Max-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Reception Table, Particle Board Top, (2400x820x1000), Model- Reception-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Reception Table, 25 mm Thick PLPB Edge Banded Top, (W1475 X D780 X H1000), Model-Reception-5, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of High Back Chair, PU Seat And Back, Seat Slide, Aluminium PU Arm, Synchro Knee Tilt, Gas Lift, Aluminium Base, Leatherette Tapestry, Model-Civic-1(A), Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of High Back Chair, Wooden Frame, Chrome Cushion Arm, Gas-Lift, Torsion Bar, Aluminium Base, Leatherite Tapestry, Model-Ibex-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of High Back Chair, PU Adjustable Arm, Synchro Tilt, Gas Lift, Mesh Back & Seat Fabric Tapestry, Model-GA 5003, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of High Back Chair, Pipe Frame, PU Chrome Arm, Gas Lift, Chrome Base, Leatherite Tapestry, Model- GS 339, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Medium Back Chair, PU Seat And Back, Aluminium PU Arm, Synchro Knee Tilt, Gas Lift, Aluminium Base, Leatherette Tapestry, Model-Civic-2(B), Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Medium Back Chair, Wooden Frame, Chrome Cushion Arm, Gas-Lift, Torsion Bar, Aluminium Base, Leatherite Tapestry, Model-Ibex-2, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Medium Back Chair, PU Adjustable Arm, Synchro Tilt, Gas Lift, Mesh Back & Seat Fabric Tapestry, Model-GA 5004, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Medium Back Chair, PP Arm, Gas Lift, Nylon Base, Mesh Back & Seat Fabric Tapestry, Model-GA 5007, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Visitor Chair, Wooden Frame, Chrome Cushion Arm, Chrome Plated, Leatherite Tapestry, Model-Ibex-3, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Visitor Chair, Wooden Frame, Cushion Arm, Chrome Plated pipe stand, Leatherette Tapestry, Model-Civic-3, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Visitor Chair, Pipe Frame, PU Chrome Arm, Chrome Plated Pipe Stand, Leatherite Tapestry, Model- GS 341, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Visitor Chair, Fixed PP Arm, Powder Coated Pipe Stand, Mesh Back & Seat Fabric Tapestry, Model-GA 5005, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Visitor Chair, Without Arm, Chrome Plated Pipe Stand, Mesh Back & Seat Fabric Tapestry, GA 587, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Cafeteria Chair Made of PP Shell Chair With Seat Cushion, Model-GC-9027, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Corner Table, MDF Top With Veneer Polish, MS Gold Finish Leg, (500x500x500), Model-Regal, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Corner Table, 25mm MDF Top, Chrome Plated Pipe Frame, (1200x600), Model-Rosemount, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Corner Table, SS Pipe Frame Chrome Finish, PLPB Edge Banded Top, 18mm Thick, Marino 10858 Colour (600x600) Model-Galaxy, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Corner Table, 25mm MDF Top, Chrome Plated Pipe Frame, (600x600), Model-Rosemount, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Corner Table, Pipe Frame, Powder Coated, PLPB Edge Bended Top 25mm Thick, (600x600), Model-Concord, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Centre Table, MDF Top With Veneer Polish, MS Gold Finish Leg, (900x900), Model-Regal, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Center Table, Pipe Frame, Powder Coated, PLPB Edge Bended Top 25mm Thick, (900x900), Model-Concord, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 1 Seater Sofa With Wooden Frame, Chrome Plated Leg, Fabric tapestry, Size in mm - 950 (L) X 770 (D) X 760 (H), Model-Rosemount, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 1 Seater Sofa With Wooden Frame, Powder Coated Leg, Twin Colour Leatherette Tapestry Size in mm - 850 (L) X 800 (D) X 840 (H), Model-Equino-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 1 Seater Sofa, Wooden Frame, SS Leg, Size in mm - 690(L) X 750(D) X 700(H), Leatherite Tapestry, Model-Questo-1, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 2 Seater Sofa With Wooden Frame, Chrome Plated Leg, Fabric tapestry, Size in mm - 1920 (L) X 770 (D) X 760 (H), Model-Rosemount, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 2 Seater Sofa With Wooden Frame, MS Powder Coated Leg, Size in mm- 1305 (L) X 700 (D) X 700 (H), Model-Walter-2, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 2 Seater Sofa, Wooden Frame, SS Leg, Size in mm - 1160(L) X 750(D) X 700(H), Leatherite Tapestry, Model-Questo-2, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 2 Seater Sofa, Chrome Plated Arm & Legs, Black Powder Coated Rectangular Tube Cross Beam, Powder Coated Perforated Seat Back. Size in mm - 1240(L) X 690(D) X 790(H), Model-Spacio-2, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 3 Seater Sofa With Wooden Frame, Chrome Plated Leg, Fabric tapestry, Size in mm - 2400 (L) X 770 (D) X 760 (H), Model-Rosemount, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 3 Seater Sofa, Wooden Frame, SS Leg, Size in mm - 1625(L) X 750(D) X 700(H), Leatherite Tapestry, Model-Questo-3, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 3 Seater Sofa With Wooden Frame, Powder Coated Leg, Twin Colour Leatherette Tapestry Size in mm - 1900 (L) X 800 (D) X 840 (H), Model-Equino-3, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of 3 Seater Sofa, Chrome Plated Arm & Legs, Black Powder Coated Rectangular Tube Cross Beam, Powder Coated Perforated Seat Back. Size in mm - 1820(L) X 690(D) X 790(H), Model-Spacio-3, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Conference Table, Particle board and MDF top, Model-4, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Conference Table, Particle Board Edge Banded Top, (2100x1200x750), Model-Conference-12, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Conference Table, Particle Board Edge Banded Top, Dia-1200, Model-Conference-14, Make-Geeken/Equivalent as Approved By Client/E.I

Providing and Fixing of Conference Table Made of 19MM Board, Top in 3 layers and Vertical drop in 3 Lair 19MM ply board. All the surface to be cladded with 4MM Veneer & Having S.S Frame Square Section of 302 Grade. All the Edges to be lipped with 4MM Veneer which shall be Melamine Polished, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.

Providing and Fixing of Discussion Table of Size (3000Lx1050Wx750HT) Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.

Supply & Installation of Café Table, SS Pipe Frame, 25mm PLPB Edge Banded Top, Dia(900), Model- GC-9064, Make-Geeken/Equivalent as Approved By Client/E.I

Providing and Fixing of Back Storage of Size (1200Lx450Wx700HT) Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.

Supply & Installation of Back Storage Unit, 18mm PLPB, Extruded Aluminium Profile, (2250x450x2200), Model-Evoke-4, Make-Geeken/Equivalent as Approved By Client/E.I

Providing and Fixing of Low Height Display Storage of Size (2700Lx450Wx900HT) Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.

Supply & Installation of Wooden Storage, Particle Board Structure, (900x450x1200), Model-Storage11, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Wooden Storage, Particle Board Structure, (1800x450x900), Model-Storage12, Make-Geeken/Equivalent as Approved By Client/E.I

Providing and Fixing of TV Pannel of Size (3000Lx450Wx750HT) Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.

Providing and Fixing of TV Pannel of Size (1500Lx450Wx750HT) Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.

Supply & Installation of Wooden Bed, Particle Board Structure, Powder Coated Pipe Frame, PPCP Shoes, Model-Hostel 5, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Basic Bed With Flat Plateform, MS Head & Foot Panel, Powder Coated, Overall Dimension - 1800mm X 900mm X 510mm, Model-GK 1007, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Bed Side Locker General, Stainless Steel Top, Powder Coated, Overall Dimension - 400mm X 400mm x 820mm, Model-GK 2002, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Baby Crib With Perforated Flat Plateform, Powder Coated, Overall Dimension - 920mm X 390mm X 900mm, Model-GK 1010, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Mattress for baby crib, Model-GK 8008, Make-Geeken/Equivalent as Approved By Client/E.I

Supply & Installation of Mattress for E N R Trolley, Model-GK 8009, Make-Geeken/Equivalent as Approved By Client/E.I

Globalzone Sanitory Infrastructure Pvt. Ltd.