CEKZ/PAN/03 OF 2019-2020

Amount

Sch 'A' Part-I (BuIlding Works) Note : This Sch is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col 5 signifies this fact only.

Designing, Manufacturing, erection and supply of pre-engineered covered accomodation for Vehicle shed (Length=140m, Width=20m and height=4 m) outer to outer including apron on front and back side garage , foundation, plinth protection ,flooring steel columns,trusses, roof covering 0.63 mm galvalume sheets, flooring including internal services complete all as shown in drawings, particular specification and designed by the contractor and duly vetted by IIT as specified..

Designing, Manufacturing, erection and supply of pre-engineered covered accomodation for Equipment Shed (Length=180m , Width=25m and height=8.25 m) outer to outer including apron on front and back side garage , foundation, plinth protection ,flooring steel columns,trusses, roof covering 0.63 mm galvalume sheets, flooring including internal services complete all as shown in drawings, particular specification and designed by the contractor and duly vetted by IIT as specified..

Lumpsum price workedout by the tenderer for EARTH WORK, EXCAVATION AND SITE DEVELOPMENT as listed in Schedule ‘A’ Part-II.

Lumpsum price workedout by the tenderer for ROAD AND CULVERT as listed in Schedule ‘A’ Part-III.

Lumpsum price workedout by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-IV.

Lumpsum price worked out by the tenderer for LIGHTING PROTECTION ) as listed in Schedule ‘A’ Part-V.

Lumpsum price workedout by the tenderer for EXTERNAL ELECTRIFIC SUPPLY isted in Schedule ‘A’ Part-VI

Lumpsum price workedout by the tenderer for EXTERNAL WATER SUPPLY isted in Schedule ‘A’ Part-VII

Schedule ‘A’ Part-VIII (MISCELLANEOUS ITEMS) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 signifies this fact only.

SCHEDULE 'A' PART-III ( ROAD AND CULVERT )Forming embankment including raising earth by supply and depositing mix of Sand & approved moorum laid in layer 150mm each spread levelled and rolled using power roller execeding 8 tonne and not exceding 12 tonne including watering and consolidation to get 97% are more density. Note: Cost of approved Moorum is inclusive of this item

M&L for 100mm th Dry lean concrete (DLC) over a prepared base with coarse & fine aggregate confirming to IS : 383 size of aggregate not exc 40mm (grading & other parameters as per table 600-1 of morth IRC SP :49 specification) design mix minimum cement concrete shall not be less than 150 Kg/Cum compressive strength shall not be less than 10MPa at 7 days, mixed in batching plant, transported to site, laid with sensor paver including speading and compacted by using double drum smooth wheeled 80 to 100 KN static weight vibratory roller including necessary fromwork finishing etc. (Construction / Expansion joints shall be speced as per paving concrete longitudinal and transeverse joints all as specified and directed).

M&L for 100mm thick (Compacted thickness) wet mix macadam (WMM) with crushed stone aggregate and stone dust (as per design mix) of specified grading, spreading at site, watered, rolled and consolidated as per required gradient and camber complete all as specified.

(INTERNAL ELECTRIFICATION) Material and labor for point wiring for one light point with 1.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multi stranded conductor 1100 volts grade controlled by one switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multi strand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including surfaced metal conduit (ERW) and clamps and others fixing accessories for fixing clamps steel space frame structures complete with necessary pressed steel sheet metal junction box/terminal box suitable for fixing on steel structure covered with 6mm thick prelaminated plastic sheet all as specified and as directed by the Engineer-in-Charge. Note: Red colored cable shall be used for live connection, black colored cable shall be used for neutral connection and green colored cable shall be used for earthing.

One light / Exhaust fan point and 5 Amp socket controlled by one way switch.

Three LED down light controlled by one switch

Four LED down light controlled by one switch

Supply and fixing Piano type switch 1 way, 6 amps, 230 volt single pole complete all as specified and as directed by the Engineer-in-Charge.

M&L for Industrial metal plug socket, 3 pin phase, neutral and earth with 10A MCB SP 01 No and industrial plug top and socket complete with all fixing and connection arrangement. Note: wiring for metal plug socket will be measured and paid under single phase sub main item.

M&L for Industrial metal plug socket for three phase and earth with 20A MCB TPN 01 NO and industrial plug top and socket (for three phase) complete with all fixing and connection arrangement. Note: wiring for metal plug socket will be measured and paid under three phase sub main item.

Supply and fix ceiling mounted High bay LED down light fittings circular LED wall glass with tapered fin design and thermal management along with IP66 protection 70/72w decorative luminaries with and including Electronic driver and LED lamp, pre-wired including necessary electric connection conforming to the following specifications: - (i) System Watts/lumens: - Max 70/72 W/Total system lumen not less than 9100 Lm. (ii) Housing: - Metal (iii) IP rating: - IP 66 totally enclosed type (iv) Front cover: - Acrylic/polycarbonate/glass cover (v) Mounting: - Recessed ceiling mounting with hook/clamps and nut bolts (vi) Finish: - Smooth finish

(vii) Lamp: - High bright LED (viii) System Efficacy (lm/Watt): - Not less than 130 lm/watt (ix) Color temperature: - Not less than 5700 K (x) Color rendering index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 hrs of operation (xii) Optics: - Designed for optimum light distribution (xiii) Control gear: - Inbuilt electronic driver with APFC, PF not less than 0.95, and THD not more than 20% of the standard operating voltage 180-270V Ac, 50 Hz+B40 (xiv) Surge protection: - Inbuilt surge protection minimum 2 KV (xv) Heat sink: - As per OEM's design (xvi) Bidder has to compulsorily submit the LM-79 and LM-80 B45and NABL accredited lab test report conforming to technical specifications and consolidated lab report for the offered LED has to be structured in the same sequence.

Supply and fix ceiling mounted medium bay LED down light fittings circular LED wall glass with tapered fin design and thermal management along with IP66 protection 70/72w decorative luminaries with and including Electronic driver and LED lamp, pre-wired including necessary electric connection conforming to the following specifications: - (i) System Watts/lumens: - Max 70/72 W/Total system lumen not less than 9100 Lm. (ii) Housing: - Metal (iii)IP rating: - IP 66 totally enclosed type (iv) Front cover: - Acrylic/polycarbonate/glass cover (v) Mounting: - Recessed ceiling mounting with hook/clamps and nut bolts (vi) Finish: - Smooth finish (vii) Lamp: - High bright LED (viii) System Efficacy (lm/Watt): - Not less than 130 lm/watt (ix) Color temperature: - Not less than 5700 K (x) Color rendering index (CRI): - Not less than 80

(xi) Color rendering index (CRI): - Not less than 80 (xii)Life: - Not less than 25000 hrs of operation (xiii)Optics: - Designed for optimum light distribution (xiv)Control gear: - Inbuilt electronic driver with APFC, PF not less than 0.95, and THD not more than 20% of the standard operating voltage 180-270V Ac, 50 Hz (xv)Surge protection: - Inbuilt surge protection minimum 2 KV (xvi)Heat sink: - As per OEM's design (xvii)Bidder has to compulsorily submit the LM-79 and LM-80 and NABL accredited lab test report conforming to technical specifications and consolidated lab report for the offered LED has to be structured in the same sequence.

Supply, commissioning and testing of LT feeder pillar outdoor type modular/combinable polycarbonate insulated which should be shock proof, safe, IP 54 according to IEC 60529 (the panel should be hold type test certificate in accordance with IEC 60439-1 (IS-8623), IEC-60439-3, the panel should have ASTA certification by CPRI and manufacturer routine test certificate should be provided), weather proof, rust proof, UV resistance, halogen free, silica free, corrosion proof, protection class-II, totally insulated, having internally embedded, polyurethane gasket with provision for cable entry through glands and/or grommets, flame retardant, self extinguishing with glow wire test at 96 degree C according to IEC-60695-2-11. Chemical resistance towards acid, and other chemicals, oils,, EMC compliant Bus Bar system, impact strength IK-08 in accordance with DIN EN 50102. (one feeder pillar per workshop/garage/repair bay) The manufacturer shall submit a type test report in accordance with IEC-60-439-1

Supply & fix Industrial Air circulator fan 230 volts, Ac single phase, 50 Hz osillating 600 mm sweep complete with connection.

Supply & fix Industrial Exhaust fan 450 mm sweep ( Roofing Turbo ventilator) Ac 230 volts, single phase, natural operated type for removal of fumes, odour and pollutants, corrosion resistant, stainless steel / Alumenium body, stainless steel shaft with teflon self lubricating bearing in low profile design flow.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 Meter deep below normal ground level) with top edge of plate not less than 1.5 Meter below normal ground level connected to galvanized iron earth wire of size 6 mm as earthing lead by means of bolt ,nuts, check nuts and washer of galvanized iron or steel besides welding of all joints as shown in drawing and including excavation and earthwork, supplying and laying charcoal dust, common salt PCC 1:2:4 type CI chamber and MS angle iron frame 40x40x3mm RCC cover 40 mm thick (1:2:4) type BI using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm c/c both ways with MS handle 12 mm dia CI funnel and wire mesh, 20 mm dia GI pipe light graded for watering all as shown in drawing and connected to earth test point including testing complete all as specified and directed .

M & L earthing complete with Gl electrode 600x600x6.00mm thick buried directly in ground vertically in pit of depth not less than 2.25 meter below normal ground level with top edge of the earth plate not less than 1.50 meter below normal ground level connected to Galvanized lron strip 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of brass connected including gun metal or phosphorus bronze of size 75x75x25 mm drilled and screwed including 3 Nos 8 mm diameter 25 mm long hexagonal head screwed all as specified including excavation and earth work and disposal of surplus soil including 40 mm Gl tubing light grade and necessary fitting for protection of Gl strip including laying of charcoal, dust and common salt PPC (1:2:3) type Cl using 20graded stone aggregate earth pit with 40x40x6mm MS angle iron grams RCC cover 40mm thick (1:2:4) type B20 using 12.5mm graded stone aggregate reinforced with 8mm diameter round bar @ 75mm C/C both way with MS handle 20mm diameter plastering 15mm thick CM (1:6:) internally and up to 150mm below ground level externally. PGL funnel with wire mesh 20mm diameter Gl pipe for watering complete all as shown on electrical plate No.3 of SSR Part -1 2009 and connected in earth test including testing completed all specified and directed.

M&L for sub main wiring single phase with 03 nos 4 sqmm PVC insulated multistranded unsheathed copper conductor for phase, neutral and earth complete with metal ERW steel surface conduit and all fixing accessories. (for metal plug socket and sub main from feeder pillar to SPN DB). Note: - 03 Nos 4 sqmm wire and ERW steel conduit combine measured as one running meter.

M&L for sub main wiring three phase with 05 nos 6 sqmm PVC insulated multistranded unsheathed copper conductor for 3 phase, neutral and earth complete with metal ERW steel surface conduit and all fixing accessories. (for metal plug socket three phase). Note: - 05 Nos 6 sqmm wire and ERW steel conduit combine measured as one running meter.

Supply, commissioning and testing of LT Panel board outdoor type suitable for 415 Volt,50 Hz, Polycarbonate (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, having high impact, made of halogen and silica free recyclable material), UV Resistant, having high grade gasket made of Polyurethane, should withstand glow wire test at 9600c, should be flame retardant, the feeder pillar panel should hold Type Test certificate (CPRI) with switchgear assemblies as per IEC60 439-1 with following accessories :- Make Hansel/Emitter/ABB/ Any Other CPRI Type Tested Makes (i) Aluminium bus bar 100 Amps capacity -04 Nosof strips.

Supply, installation, testing and commissioning High galvanized mast light suitable for and including 8 lantern (1x120 watts LED Flood Light IP 65 lamps fittings) symmetrically fitted along with their control gear and having two point suspension system with stainless steel wire rope of 6 mm diameter 97/19 gauge and double drum winch with luminaries mounting arms, fully assembled, aviation obstruction light, lightening arrester spike including RCC M-25 foundation as per manufacture instruction 16 Meter height complete as per following specifications .Make: Crompton Greaves/Phillips/Bajaj /Wipro 1. Height: 16 Meter with Power Tool

2. Material : Hot dipped galvanized as per specification BSEN ISO1461.Each section shall be fabricated out of individual plates duly folded and welded. There shall be only one longitudinal seam weld per section. Hot deep internally and externally having uniform thickness of 85 microns for bottom section and 65 microns for top and middle section 3.Top and bottom Dia. & Thickness: 150 mm (thickness 3mm) and 460 mm (thickness 4mm) 4 . Overlap: 1.5 times the Diameter :At site sections shall be joined together by slip-stressed- fit method. No site welding or bolted joints shall be done to the mast. 5 Max. Dynamic loading to withstand Max. Wind Pressure :As per IS-875 Part 3 6. Opening of base door :1200 X 250mm 7.Double internal lock: To be provided. 8. Base plate :25mm thick 670mm Dia. The welding connection of the base flange shall be fully developed to the strength of the entire section. The base flange shall be provided with supplementary gussets between the bolt- holes to ensure elimination of helical stress concentration 9. Anchor Plate : 8 mm 10. Lantern Carriage arrangement :Lantern carriage of 50 NB ERW Class- BM.S pipe covered with PVC sleeve suitable to carry 250 Kg load up to 9 fittings

10. Lantern Carriage arrangement :Lantern carriage of 50 NB ERW Class- BM.S pipe covered with PVC sleeve suitable to carry 250 Kg load up to 9 fittings 11. Raising and lowering mechanism :Completely self sustaining Winch fixed at the base without the need of brake shoe, spring or clutches. Gravity activated pawls. Gear ratio 53:1,with self lubricating oil bath. 12. Head Frame; to be provided of Galvanized type. rane Assembly: KONE 13. MCB erected at PVC Board; To be provided of suitable rating. 14. Lighting protection - By G.I. single spike 1200mm at top 15. Trailing - PVC sheathed 8 X 2.5 Sq. mm copper cable 16.Wire rope - 2 Nos stainless steel wire rope 7/19, 6mm dia. Breaking load capacity 2400 Kgx2 17.Integral power tool - 3 Ph 1 HP 2m/ min single speed, 18.Torque limiter - Up to 500Kg adjustable 19. Aviation obstruction light - Twin dome with 2 Nos LED lamp .

20. Light Fixtures : Eight (08) Nos. The complete integrated weather-resistant luminaries IP66 designated as HIGH MAST luminaries in Circular or Rectangular Shape, with powder coated frame and toughened glass suitable for operation of one 120 watt LED with luminous efficacy not less than 120 Lumens per watts lamp from a nominal 240 volt, 50 Hz power source and shall be capable of starting and operating the specified lamp within the limits specified by the lamp manufacturer. Each luminaries shall be provided with individual surge suppressor 5KV Standard construction in IP66 for enclosed luminaries. The luminary shall be of same make as the High Mast light.

KAIZEN INDUSTRIES

M/S SUNRISE ENTERPRISE

surendra infrastructure pvt ltd

NIRMAL SALES CORPORATION