Repair to flooring roofs internal water supply and misc Work at MH MIDC in the area of AGE B/R I under GE (N) Ahmednagar

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) etc complete all as specified and directed by Engineer-in-Charge

Demolition of precast concrete block walling built in cement and sand mortar etc complete all as specified and directed by Engineer-in-Charge

M&L for brick work with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M&L for cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in lintel upto 1.50m clear span, cills, steps, seismic and other similar bands, copings and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork etc complete all as specified and directed by Engineer-in-Charge

Dismantling plain or corrugated steel sheeting/AC sheet any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed by Engineer-in-Charge

Supply and fix pressed steel frames of any size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge

S&F Steel work in tubular / hollow section in trusses, rafter, purline, post etc. including special shaped washer, plate, cleat, etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 etc complete all as specified and directed by Engineer-in-Charge

S&F Pre - painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed by Engineer-in-Charge

S&F Pre - painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed by Engineer-in-Charge

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or any type ceiling board any thickness any position with nails etc complete all as specified and directed by Engineer-in-Charge

S&F powder coated aluminum alloy interlocking snap grid 600mmx600mm consists of min tee runners of size 38mm x 25mm x1.5mm and cross Tee of size 25mm x 25mm x 1.5mm spaced between the main Tee at 600mm centre to cntre to form a grid of 600mm x 600mm etc complete including GI wire hangars at 1200 mm intervals all as specified as per manufacturere's instructions etc complete all as specified and directed by Engineer-in-Charge

M&L for 4mm thick non asbestos fibre cement building boards of make 'E' board classic designer board (cascade or Occenic) of M/s Everest Industries Ltd of equivalent as approved by GE fixed or laid/inserted to timber/GI/Aluminium frame work with etc complete all as specified and directed by Engineer-in-Charge

Dismantling of single layer Mangalore pattern or similar tiles in roofing etc complete all as specified and directed by Engineer-in-Charge

M&L for roof tiles, Mangalore Pattern, interlocking at side joints, laid dry etc complete all as specified and directed by Engineer-in-Charge

All as per item No 14 (here-in-before) but except tiles

M&L for ridges and hip tiles to joint mangalore patern tiles or roofing bedded/ jointed in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor etc complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises etc complete all as specified and directed by Engineer-in-Charge

M&L for Virified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles exc 0.11 Sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor laid over and including 15 mm thick screed bedding in cement and sand mortar (1:6), set and jointed in neat cement slurry and pointed white or in coloured cement to match the floor etc complete all as specified and directed by Engineer-in-Charge

All as per above Item No 19 (here-in-before) but as in skirting laid over and including a backing coat of 10mm thick in cement and sand mortar (1:4)

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor laid over and including 15 mm thick screed bedding in cement and sand mortar (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of floor etc complete all as specified and directed by Engineer-in-Charge

M&L for glazed ceramic coloured tiles of size 350 X 250 X 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement and sand mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of floor etc complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 10 mm thick on stone masonry surfaces in cement and sand mortar (1:4) on wall finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 15 mm thick on stone masonry surfaces in cement and sand mortar (1:6) on wall surface finished even and smooth without using extra cement with sagol finish etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 5 mm thick on concrete surfaces in cement and sand mortar (1:4) on ceiling finished even and smooth without using extra cement with sagol finish etc complete all as specified and directed by Engineer-in-Charge

M&L for applying two coats of cement base paint on newly plastered surfaces incl preparation on wall etc complete all as specified and directed by Engineer-in-Charge

M&L for applying two coats of oil bound distemper on newly plastered surfaces of walls paint over 2mm thick wall care putty including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for applying one coat of OBD on Old plastered surfaces of walls including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for complete removal of existing treatment on plaster and applying two coats of OBD over 2 mm thick wall care putty on old plastered surfaces of walls including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for applying two coats of white wash on newly plastered surfaces incl preparation etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old wall surfaces of any description & applying one coat of acrylic (antifungal) exterior grade paint on wall/roof etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old plastered surfaces of wall and applying one coat of cement paint on wall etc complete all as specified and directed by Engineer-in-Charge

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in sub base etc complete all as specified and directed by Engineer-in-Charge

M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement and sand mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed by Engineer-in-Charge

M&L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement and sand mortar (1:6) set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; etc complete all as specified and directed by Engineer-in-Charge

M&L for Shahabad stone 25mm to 40mm thick flooring screed bed or bedding layer of mortar 15 mm thick in cement and sand mortar (1:6) for laying floor finishes to receive tiles and stone slab etc complete all as specified and directed by Engineer-in-Charge

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment in floors etc complete all as specified and directed by Engineer-in-Charge

M&L for machine cut kota stone slab florring 18-20 mm thick laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing etc complete all as specified and directed by Engineer-in-Charge

Taking down shutter exc 1.5 sq. m but n.exc 2.0 sq each etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 30mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial. kiln seasoned if one face is covered with decorative face veneer with lipping/frame to match the shade etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 35mm thick skeleton shutters, open rebated and to receive glass, gauze, etc(without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitered beads for securing glass, etc; sizes of me-mbers of shutters as specified in SSR Part-I, section 8, clause 8.24(a) etc complete all as specified and directed by Engineer-in-Charge

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed by Engineer-in-Charge

S&F factory made solid PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails frame shall be covered with heat moulded plain coloured PVC `C' channel having a PVC sheet strip of 20 mm width stuck and plain colour PVC sheets for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame etc complete all as specified and directed by Engineer-in-Charge

Taking down aluminium doors/windows shutters only and dismantling all members and reassembling the same with and including new screws, new rubber gasket new alumunium cleats of exesting make and alxo refixing the locks & roller in existing position with and including new screws refixing the window shutter in same opening etc complete all as specified and directed by Engineer-in-Charge

S&F 100 mm long butt hinge, medium weight, cold rolled stainless steel etc complete all as specified and directed by Engineer-in-Charge

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections etc complete all as specified and directed by Engineer-in-Charge

S&F 150 mm long aluminium anodised handle, cast type etc complete all as specified and directed by Engineer-in-Charge

S&F aluminium extruded section door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed etc complete all as specified and directed by Engineer-in-Charge

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engineer-in-Charge

S&F powder coated anodised aluminium fully glazed door shutters side hung type, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed by Engineer-in-Charge (Note : Glass will measured and paid separately)

S&F powder coated anodised aluminium glazed window shutter side hung / aluminium sections weighing 0.55 kg/m aluminium open track section having reqd size of style and top rails, bottom rails including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 No.) etc complete all as specified and directed by Engineer-in-Charge (Note : Glass will measured and paid separately)

M&L Block board, 12 mm thick, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, fixed with screws to timber frame work etc complete all as specified and directed by Engineer-in-Charge

M&L for second class hard wood beads, straight (any size) for glazed or gauzed joinery, renewed, including mtrs etc and removing old beds etc complete all as specified and directed by Engineer-in-Charge

S&F stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples etc complete all as specified and directed by Engineer-in-Charge

All as per item No 57 (here-in-before) but fixed in repairs.

M&L for 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 Sq. m in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers etc complete all as specified and directed by Engineer-in-Charge

M&L for PVC sheets or insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall or Aluminium frames etc complete all as specified and directed by Engineer-in-Charge

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring etc complete all as specified and directed by Engineer-in-Charge

S&F in repair mortice lock, vertical type, size 100mm brass 4 levers etc complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones etc complete all as specified and directed by Engineer-in-Charge

M&L for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

M&L for glazing with 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc complete all as specified and directed by Engineer-in-Charge

S&F continous (piano) hinges, stainless steel, bright finish or electrogalvanised (width of flaps 30mm ) etc complete all as specified and directed by Engineer-in-Charge

S&F 125mm hasp and staple, safety type, aluminium anodised with stainless steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified and directed by Engineer-in-Charge

S&F 125 mm long aluminium anodised handle, cast type etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of priming with red oxide etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed by Engineer-in-Charge

S&F in repair Stainless Steel decorative powder coated curtain rods with fixing brackets,knobs, rings etc complete all as specified and directed by Engineer-in-Charge

S&F in repair 10 mm thick semi circular glass for shelves in corner with chamferred edges including connected brackets etc all as spfd and directedn. exc 0.35 m in radius etc complete all as specified and directed by Engineer-in-Charge

S&F in repair health faucet with all connected accessories etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair wall mixture, 3-in-1 with provn for both telephone shower & over head shower with 115 mm long bend type & wall flange etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair Brass Chromium Plated toilet paper holder fixed with (CP) brass screws of approved quality etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs decorative towel ring chromium plated fixed with (CP) brass screws of approved quality etc complete all as specified and directed by Engineer-in-Charge

S&F in repair, brass chromium plated tubular towel rail, 20mm dia, C type, 60cm long between flanges etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in 15mm dia bore pipe etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair Self-closing flush taps for urinal, cast copper alloy, chromium plated, screwed for iron pipe and fixed 15mm bore pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repair, bib tap 15 mm dia, fancy type chromium plated, cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair, 15 mm dia stop valve, fany type chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs, shower rose, 125 mm size, brass chromium plated with sweivel joint etc complete all as specified and directed by Engineer-in-Charge

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm etc complete all as specified and directed by Engineer-in-Charge

Dismantling of water tanks of capacity exc 250 and n.exc 500 ltrs and removing from site etc complete all as specified and directed by Engineer-in-Charge

Dismantling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site etc complete all as specified and directed by Engineer-in-Charge

All as per item No 86 (here-in-before) but 2000 ltr capacity.

S&F rotational molded polyethylene water storage tanks double layer(cylindrical vertical with closed top) of 500 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting including taking down old water tank etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 88 (here-in-before) but 1000 ltr capacity

All as per item No 88 (here-in-before) but 2000 ltr capacity.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair all as specified and as approved by GE/Engineer-in-Charge.

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe etc complete all as specified and directed by Engineer-in-Charge

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe etc complete all as specified and directed by Engineer-in-Charge

All as per item No 93 (here-in-before) but 20mm dia pipe.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling etc complete all as specified and directed by Engineer-in-Charge

All as per item No 95 (here-in-before) but fixing only.

All as per item No 95 (here-in-before) but 20mm dia pipe.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overalll as fixed along the cente line over fittings and accessories) etc complete all as specified and directed by Engineer-in-Charge

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge

S&F 110 mm bore PVC (SWR) branch piece double (single Y) equal or unequal etc complete all as specified and directed by Engineer-in-Charge

S&F 110 mm dia PVC (SWR) bend any radius etc complete all as specified and directed by Engineer-in-Charge

S&F 75 mm dia PVC (SWR) bend with access door any radius etc complete all as specified and directed by Engineer-in-Charge

S&F PVC (SWR) floor trap, 75 mm dia with grating including jointing with solvent cement etc complete all as specified and directed by Engineer-in-Charge

M & L for for providing water proofing treatment on roofs as per latest zonal specification , as per manufecturer's instructions and as specified after taking down/out as existing at site :- (a) M & L for Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.25 ltrs/sqmts and allow to dry. (b) M & L for Applying and laying torch APP polymer modified bituminous membrance 3 mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts with white gravel/mineral finished by thermofusion process.

M & L for Plastering 10 mm in cemnet and sand mortar (1:3) using 100% course sand on roof mixed with & including M & L for WPC @ 3% by weight of cement and finished the surfaces even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor etc complete all as specified and directed by Engineer-in-Charge

S&F in repair vitrieous china white wash down WC (Pedestal pattern) white and flush piple including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete all as specified and directed by Engineer-in-Charge

S&F in repair vitreous china white wash hand basin Flat back Pedastal pattern of size 580x450mm for hospital use), long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in cement and sand mortar (1:3) including 32mm dia chromium plated waste coupling/trap etc complete all as specified and directed by Engineer-in-Charge

S&F in repair Vitreous China white urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including conncetion to flushing pipe and waste pipe providing and fixing plugs bedding urinal against wall etc complete all as specified and directed by Engineer-in-Charge

Supply and fixed in repairs stainless steel kitchen sink matt finish with draning board over all size 915 x 510 mm and bowl size 510 X 405 X 200 made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed

An amount of Rs 49,195.00 shall be deducted from BOQ on account of schedule of credit

Priyadeep Construction

HG PATHAN CONSTRUCTION COMPANY

M/S-B.R.SONAWANE

M/S. M. F. Sharif & Co.

M/s. Sagar Traders

M/s Meher Construction