REPAIR/MAINT OF WATER SUPPLY RISING AND DISTRIBUTION LINE CHLORONOME PLANT, PUMP SETS AND CONNECTING E AND M WORKS OF ZONE I AND ZONE II AT CANTT AREA UNDER GE (I) KANPUR.

Amount

Excavation in trenches not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide in any type of soil for laying and taking out of GI/CI pipes all as specified and directed.

Returning filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm thick complete all as directed.

Removing excavated soils to a distance not exceeding 50 m and depositing where directed.

M&L for drilling hole at a depth up to 1.5 mtr below the normal ground level of suitable size to insert upto 150 mm dia pipe across the road in horizontal position complete all as directed.

M&L for cutting of road depth up to 1.5 mtr below the normal ground level of suitable size to lay pipe upto 150 mm dia pipe across the road in horizontal position( upto 7 Mtr) incl making good all disturbed surfaces of road to match with existing surfaces by premix road material/PCC complete all as directed.

Disconnecting, dismantling and taking up or down old/unserviceable/cracked GI tubing with fittings of size 15 mm bore incl cleaning for refixing complete all as spfd and directed. Note: Excavation and earth work will be measured and paid separately under relevant items.

All as per Srl No 6 above but of size 20mm.

All as per Srl No 6 above but of size 25mm.

Re-laying, jointing and testing old but serviceable GI tubing 15mm dia (obtained from srl item No-6) and connection in new or old portion incl new fittings such as bends, elbows, union, tees, reducers etc as required at site laid in trenches or on floor or wall complete and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed.

All as per Srl No 9 above but of size 20mm (obtained from srl item No-7).

All as per Srl No 9 above but of size 25mm (obtained from srl item No-8).

Supply & Laying (in replacement), jointing and leakage testing GI tubing medium grade 15mm bore with all fittings such as bend, tee, elbow, union, reducer etc, laid in trenches/floor/walls and making good the disturbed surface to match with existing surface as (PCC work in 1:2:4 using 20 mm graded stone aggregate/ plastering in CM 1:4 and applying finishing coat of existing treatment) complete all as specified and as directed at site. Make: Tata/Jindal/Prakash Surya as approved by GE(I). Notes :(i) The laying and jointing of pipes are required to be carried out in short / long streches catering to specific requirements of a purticular quarter or a group of blocks. (ii) Excavation & earth work shall be measured & paid seperately.

All as per Srl No 12 above but of size 20mm.

All as per Srl No 12 above but of size 25mm.

All as per Srl No 12 above but of size 40mm.

All as per Srl No 12 above but of size 50mm.

All as per Srl No 12 above but of size 80mm.

Disconnecting, dismaantling and taking down CI/GI/DI/Cemented pipe line of size 100mm bore, including all fittings with spigot and socket/ flanged end or any type, lead joint including removing from site complete all as specified and directed.

All as per Srl No 18 above but of size 150mm.

Re-laying, jointing and testing old but serviceable CI/DI pipe line of size 100mm bore after cleaning as taken down under Srl item No 24 here-in-before including all fittings as required at site complete and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and directed.

All as per Srl No 20 above but of size 150mm (obtained from srl item No-25).

M&L in replacement of ductile iron pies 100mm bore incl rubber gasket joints and other relative accessories, class K-7 in any length laid in trenches complete all as specified and directed.

All as per Srl No 22 above but of size 150 mm.

All as per Srl No 22 above but of size 200 mm.

S&F in replacement of cast iron double flanged sluice valve of size 80mm bore class PN 1.0 confirming to IS 14846/2000 with with high tensile stainless steel spindle with CI wheel, Gun Metal Nuts/rings 'I' bolt, ISI marked including replacement of rubber packing complete all as specified and directed.

All as per Srl No 25 but sluice valve of size 100mm.

All as per Srl No 25 but sluice valve of size 150mm.

Supply and fix flanged end lift type Foot valve 150 mm dia, suitable flanges, nuts, bolts, gaskets complete all as specified and directed.

S&F in replacement of cast iron double flanged Non return valve of 150 mm dia class PN 1.6 confirming to IS 14846/2000 with with high tensile stainless steel spindle with CI wheel, Gun Metal Nuts/rings 'I' bolt, ISI marked including replacement of rubber packing complete all as specified and directed. Make : Kirloskar/Upadhyay.

M & L for boring on existing CI pipe upto 200 mm dia for branch connections of up to 50mm dia pipe by fixing of MS clamp 50x4mm cut to length and bent to shape, drilled and welded with GI socket of suitable size incl rubber packing, nut, bolt etc and testing complete all as specified and direted.

Repair to GI pipe lines of size 15mm to 25 mm bore dia and repair to leaked joints of pipe line complete including replacement of old GI fitting i.e union,nipple & sockets etc including excvation and taking up & down GI pipe required cutting & threading refixing in position in trenches and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed.

Repair to GI pipe lines of size 40mm to 80 mm bore bore dia and repair to leaked joints of pipe line complete including replacement of old GI fitting i.e union,nipple & sockets etc including excvation and taking up & down GI pipe required cutting & threading refixing in position in trenches and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed.

Cutting existing CI/DI water main 150mm bore pipe in position for making branch connection and CI/DI pipeline (Insertion of CI/DI tees bends of different size on connection pieces or for insertion of sluice valve) including excavation & earth work. Note : Fittings such as tees, bends, collars & reducers etc incl in this item and only run lead joints, CI/DI fittings & sluice valve shall be measured and paid separately and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed.

All as per srl No 33 but of size 100 mm.

All as per srl No 33 but of size 80mm.

M&L for Run lead joints complete with spun yarn of size 80mm dia all as spfd and directed.

All as per srl No 36 but of size 100 mm.

All as per srl No 36 but of size 150 mm.

M&L for Cast iron/ductile iron special fittings for spigot and socketed pipes such as bends (any type, radius and angle) socket tapers any type, (straight, bend, increasing, decreasing or double socket etc) Tee pieces, single branch, Y junction, double branch, cross (all sockets or socket and spigot) collers, caps and plugs for upto 150 mm bore pipes complete all as specified and directed.

S & F stop valve 20mm dia, gun metal iron, screwed down, high pressure with crutch or butterfly handle, screwed for iron pipe or for ferrule ISI marked including dismantling the old U/S existing valve complete.

M & L for opening up of leaking sluice valve 80mm and repacking of stuffing box & replacement of gland packing, nuts, bolts & washers etc complete all as specified of the following sizes :-

All as per item No-41 but of size 100 mm dia.

All as per item No-41 but of size 150 mm dia.

S & F gun metal iron gate valve 20mm dia with iron wheel head, screwed both ends for iron pipe, ISI marked, complete all as specified including dismantling the old unserviceable existing valve complete.

All as per srl item 44 but of size 25 mm bore.

All as per srl item 44 but of size 40 mm bore.

All as per srl item 44 but of size 50 mm bore.

M&L joints with rubber gaskets for CI flanged pipe including necessary nut bolts and washers etc for pipe 80 mm bore all as specified.

All as per srl item 48 but of size 100mm bore.

All as per srl item 48 but of size 150mm bore.

Cutting and removing unwanted grass and wild growth including bushes and shrubs from the roots at water supply installations including removing and even finish the entire area complete all as specified and directed at site by Engineer in charge.

Supply and Pouring of sodium based granular having chlorine content 60-70 % disinfectant for water treatment, more stable than Chlorine Gas, and stronger than bleaching powder, and sodium Hypochlorite packing in 45 kg drum completed all as specified & directed. E-in-Cs approved .

M & L for construction of valve pit chamber in replacement 600 x 600 x 950 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces incl dismantling and removal of old unserviceble valve pit remains all as specified and directed.

M & L for construction of valve pit chamber in replacement 950 x 950 x 950 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces including dismantling and removal of old unserviceble valve pit remains all as specified and directed.

Cleaning/removal of grass/bushes/plants/mud etc all around/inside the valve pit chamber up to size 950mm x 950mm x 950mm complete all as spd and directed all as specified and directed.

M & L for repairing micro processor based/ other type of water level indicator system in between over head tank sensor to main water level indicator LED display unit showing indication at pump operator room by replacing the circuit board & all other accessories complete all as specified and directed.

supply ,fixing and testing micro processor based water level indicator system in between over head tank sensor to main water level indicator LED display unit showing indication at pump operator room by replacing the circuit board & all other accessories complete all as specified and directed.

M & L for repairing leakages of CI pipes of size 100/150 mm with spigot and socket ends, including de-watering of pipe lines and trenches, burning out joints to recover lead and making new lead joint with retrieved material and any additional quantity of lead required as per site requirement incl all other materials such as spun yarn, fire wood incl excavation ,earth work (upto 1.5 mtr depth) by manual as required at site etc and making good the disturbed surface to match with existing surface as (PCC work in 1:2:4 using 20 mm graded stone aggregate) complete all as specified and as directed.

Taking up/down pipe line including excavation, returning filling and removal of excavated soil near existing pipe line of size 80 to 200 mm bore in break down maint of rising main line/distribution line. Providing any type of special tools & plants such as JCB & material (such as detachable joints/leak repair clamp suitable for CI/DI fittings, coller/short pieces of pipes or any other fittings as required to minimize the breakdown time and rectification of the problem as soon as possible. Rectification work must be start within two hours of intimation to contractor. Any delay in rectification may be penalized as deemed fit. Note: Excavation and earthwork if any shall be measured and paid separately under respective items

Repair/maint of LT panel /Starter of any size/type, checking and tightening of all incoming and outgoing connections by replacing alluminium lugs, pieces of burnt wires as required to make the starter /panel functional .

Minor repair/cleaning/servicing/maintenance and testing of chlorine granuals based dosing plant comprising of dosing pump, agitator and FRP tank and connected pipe lines etc daily for 15 Nos of Installations :- Note : (a) Testing of chlorine at consumer end with medical authority and maintained chlorine test record once a week on a register and submit report to concern JE E&M/Engr-in-Charge. (b) Servicing of Agitator of by using necessary lubricant, replacement of bush/bearing, alingning the shaft , key etc. deemed to be included in item rate. (c) Any other spares required for replacement shall be supplied and fixed under relevent item of Sch 'A'. (d) If any defect found in plant contractor should rectify the defect with in 24 Hrs, if failed to rectify the decfect the contractor shall be liable to pay compensation Rs 500/- (Rupees five hundred only) per plant per day. (e) Cost of minor essential items such as nuts, bolts,washers etc. Which are not otherwise specified in this Schedule but are essential for smooth functioning of the chloronome plants are deemed to be included in the quoted rate. (f) Adequate reserve for all necessary spares /stores will be kept at the site by the contractor to avoid any delay in carrying out the repairs works. (g) All T&P required to carry out the work at site will be provided by the contractor. Cost of the same shall be deemed to be included in the unit quoted rates. (h) All safety precautions including proper gas mask kit will be provided to the technicians by the contractor.

S&F in replacement of Motor 230 volt, 50 Hz, voltage input 230 volt single phase 50 Hz, current consumption 0.4 Ampr power 120 watt, speed 4 pole induction non synchronous 920 RPM Approx under lead motor shaft dia 15mm X Length 50 mm motor is flange mounted 4 no of 7 mm dia hole at PCD 150 mm incl all fixing arrangement.

S&F in replacement of shaft complete with impeller made out of MOC poly propelene rigid dia 32 mm X Length 500 mm impeller type two bladed pitched blade turbine numbar of impeller- I incl all fixing arrangements.

S&F in replacement of Dosing tank only capacity 100 Ltrs MOC PE FRP Ltd contaning port hole for pouring chlorination chemical and water them necessary provision for mounting of moteo at proper angel provision for mounting dosing pump on lid level gauge.

S&F in replacement of Rotor assembly with bearing brackets & tolerance ring complete all as specified and directed.

S&F in replacement of Single head feet rate control with shaft complete all as specified and directed.

S&F in replacement of Pump head ( ferrules 1/4"" & duchbill included) complete all as specified and directed.

S&F in replacement of Pump tube complete all as specified and directed.

S&F in replacement of Injection check valve complete all as specified and directed.

S&F in replacement of Weighted suction line strainer 3/8'' complete all as specified and directed.

S&F in replacement of 3/8'' white suction/discharge tubing complete all as specified and directed.

S&F in replacement of Check valve duckbill only (PK-5) complete all as specified and directed.

S&F in replacement of Gear motor complete 230 volt 50 Hz all as specified and directed.

S&F in replacement of Coil 250 volt 50 Hz complete all as specified and directed.

S&F in replacement of Roller Assembly complete all as specified and directed.

S&F in replacement of dosing pump "As per exitnig sample" high pressure single head geared motor adustable dosing having output upto 40 US GPD and pressure upto 7 kg/cm2 with connecting accessories complete all as directed by engineer in charge.

M&L for painting of steel and iron parts of chlorine plant including prearation of old painted surfaces with two coat of synthetic enamel paint all as directed by Engr-n-Charge. Make of Paint : Asian/Narolac/Burger

M & L for rewinding of agitator motor of capacity 120 watts, 960 RPM single phase 230 V and using copper winding wire of existing gauge with necessary insulation material including testing after repair and refixing of the same complete all as directed.

Taking / lifting out defective submersible pumps set from bore well complete with column pipe upto 150mm dia, steel rope, submersible cable and accessories etc and relowering and commissioning the same after repairing works and testing complete of rating 45/40/30/20 HP 3 phase

Dismantling, taking out complete burnt winding wire of submersible motor including cleaning of stator slots replacement of defective parts and rewinding with existing type & gauge of copper winding wire pvc insulated as per motor capacity and using new insulation material such as insulating paper sleeves etc.replacement of submersible cable as required size/ length complete incl testing all as directed of rating 30 to 40 HP 3 phase.

Dismantling submersible pump, straightening & polishing of pump shaft, making threading and key way, turning surfacing polishing to impellers, CI bowl complete including replacement of worn out parts as per requirement complete incl testing and all as directed of rating 40/30/20 HP 3 Phase .

S & F in replacement of Motor bush of gun metal upper and lower for 45/40/30/20HP capacity (Set of two)

S & F in replacement of Rotor bearings sleeve upper and lower for 45/40/30/20 HP capacity, (set of two.)

S & F in replacement of coupling arrangement with key for motor for 40/30/20 HP capacity

S & F in replacement of Sand guard for submersible pump set for 40/30/20 HP capacity

S & F in replacement of Thrust bearing assembly for submersible pump set motor for the capacity 40/30/20 HP

S & F in replacement of Epoxy type cable jointing kit complete with all the jointing material, ferrule, for 1100 volts flat submersible copper conductor cable 16/10 Sqmm 3 core Make : M seal/Reychem/Birla 3 M

S & F of Rubber gasket (packing) suitable for 80 to 150 mm dia flange.

S & F in replacement of MS Nut bolts with spring washers of any sizes.

S & F in replacement of Steel wire rope stranded 12 mm dia for hanging of submersible pump set .

S & F in replacement of Electric cable for submersible pump set, flat 16 Sqmm 3 core stranded copper conductor PVC sheathed cable all as specified and directed. Make- Finolex/ Paragon/Havells

S & F in replacement of impeller with key and distance bushes for 45/40/30/20 HP capacity pump

S & F in replacement of Pump shaft of stainless steel suitable for 45/40/30/20 HP capacity pump

S & F in replacement of NRV for 45/40/30/20 HP capacity pump

S & F in replacement of Bearing bush for submersible pump for 45/40/30/20 HP capacity.

S & F in replacement of Bowl assembly for submersible pump set for the capacity 45/40/30/20 HP

S & F in replacement of Distance sleeves for submersible pump for 40/30/20 HP capacity.

M & L for repair/maint of monoblock pump set of 5/3 HP capacity by means of dismantling from foundation derusting of shaft filling of gland packing replacement of seal bearing etc necessary repair in foundation to make rigid the system and arrest the vibration all as directed.

Dismantling the motor , taking out the burnt copper winding wire of motor 3/5 HP and Rewinding of motor with existing copper wire of existing gauge as per motor capacity using new insulation material such as insulating paper sleeves etc. bakinmg complete with super enamelled insulating varnish including cleaning of stator slots and testing complete, all as directed.

S & F in repair MCCB TP, 415V, 100 Amps with breaking capacity 10 KA (as per sample). Make- L&T/Legrand/Siemens

S & F in repair MCCB TP, 415V, 200 Amps with breaking capacity 25 KA (as per sample). Make- L&T/Legrand/Siemens

S & F of in repair Power contactor TP as per existing type & make fitted at site for starter suitable for 40 HP/30HP/20 HP submersible pump set. Make- L&T/Legrand/Siemens.

S & F in repair Over load relay (as per sample) for starter suitable for 40 HP/30HP/20HP submersible pump set. Make- L&T/Legrand/Siemens

S & F in repair Timer (as per sample) suitable for star delta starter for 40/30/25/20 HP submersible pump set. Make- L&T/Legrand/Siemens

S & F in repair fully automatic star delta starter for submerssible pump set including connecting all incoming and outgoing copper wire as directed . Make- L&T cat part No-MU-G 50 or equivalent to SEIMENS / BCH.

S & F in replacement fully automatic star delta starter for submerssible pump set including connecting all incoming and outgoing copper wire all as directed . Make- L&T cat part No-MU-G 30 or equivalent to SEIMENS / BCH.

S&F in replacement change over switch on load type in open execution front handle operated 415V with rating of 200 Amps four pole 415 volt with box and incl fixing arrangements on wall or panel. Make:-Havells /Legrand/L&T

Supply only sodium hypo chloride ( Chloine percentage 10-11%) for swimming pool water in manufacturer standard packing all as directed. Make- Bihar Coustic & Chemical/Hybird

Supply & pouring of Crystal Alum (Ferric) in swimming pool all as spfd.

Supply & pouring of Copper Sulphate in swimming pool all as spfd.

Supply & pouring of Chemi coat, Algae-cide liquid in swimming pool all as spfd.

Supply & pouring of Soda ash (Tech) in swimming pool all as spfd.

M & L for carrying out drinking water test as per IS 10500-2012 (45 parameters) viz, coliform, E coli,aluminium (as Al), arsenic( as As), Boron (as B), Cadmium (as Cd), calcium (as Ca),chloride (as Cl),,total Chromium (as Cr),colour Copper (as Cu),Cyanide (as CN) detergents,Flurides (as F),Iron (as Fe),Lead (as Pb),Deg c,phenolic compounds,residual free chlorine,selenium (as Se),solid dissolved (TDS), Sulphate (as SO4) ,taste,Total Alkalinity,Total Hardness( asCaCo3) ,Turbidity,Zinc (as Zn), ammonia as total ammonia N,Barium (as Ba),chloarines (as Cl2),silver as(Ag), sulphide (as H2S),molybdenum (as Mo),Nickel (as Ni),Trihalomethanes as ( Bromoform, dibron, oehloromethane, bromodichloromethane, chloroform, mineral oil, polychlorinated biphenyl (PCB), polynuclear aromatic hydrocarbons (PAH) Total pesticides residues,radioactivity test( alpha& beta radiation) at an NABL accredited lab and submission of tests reports in 10 days time from date of collection of sample. Note :- 1. Item will be deemed to include collection of water by the lab supervisused in precense of JE/Engr-In-Charge and incl transportation of samples. 2. Lab will be approved by from the GE prior to collection of samples. 3. Location and time of collection will be decided by Engg-in-Charge.

Supply & fixing for GI strip 32x6mm on wall/batten or recessed or buried in ground all as directed by Engineer-in-Charge.

Supply and Fixing of MS column pipe heavy Duty of size 150 mm in standard length of 3.0 mtr, heavy duty duly threaded at ends with provision of MS flange duly drilled and welded incl gasket, nut, bolts and washers, all as specified & directed. Make : Jindal/TATA.

Supply and laying pea gravel for packing of size 3 to 5 mm to be designed by the contractor of natural shape brought direct from river bed and packing around the casing pipe and slotted pipe complete all as specified and directed.

Development of bore well of any capacity sixe, not ,ore than 150 mtr deep at the pressure upto 600 PSI diesel enhgine driven air compressor of capacity 500 CFM with and including air pipe and connected items to achive the minimum yield of 3 inches by V-Notch reading of tube well complete all as specified and directed.

S B ENTERPRISES

M/S PASHUPATI TRADERS

Preetpowercontrol