SPECIAL REPAIR OF BLDG NO P-41 (QUARTER GUARD AND KOT) OF 12 SIKH LI UNDER GE (I) KANPUR

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick work or stone/boulders masanory built in cement mortar including all quoins, arches, pillars etc, but excluding ashler facing, dressed stone work and precast concrete articals complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

Taking down cement plaster on wall & ceiling including raking out joint, hacking for key scrubbing down with water etc complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frame) n. exc 1.5 sqm including making good dismantled portion by brickwork, concrete (1:2:4) or CM(1:3) and plastering complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm n exc 4 sqm including making good dismantled portion by brickwork,cement concrete (1:2:4) or CM(1:3) and plastering each complete all as specified and directed.

M&L for 12mm thick ready to use cement based plaster (Ready mix plaster) with high quality polymer additive and well graded sand and fillers over wallof brick, stone or concrete including preparing the surfaces clean and made free from dirt,oil grease,concrete sealer or curing compound using a wire brush of mopping. Dampen the surface with clean water. water to be mixed/ preparation of mortar to be done as per manufacturer instruction complete all as specified and directed.

All as per item No 8.00 above but 5mm thick on ceiling complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in built in cement mortar 1:6 complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for 25 mm thick PCC Type B-0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling /sub base of flooring complete all as specified and directed.

M&L, Non-skid ceramic coloured tiles, 7 to 8 mm thick (square/rectangular) of size 400 x 400 mm , in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement over and including15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450x300 mm & 6 to 7 mm thick on vertical surface of walls such as in dado, skirting etc; including and jointing in neat cement slurry and pointed in white cement mixed with pigment to match with shade of tiles over and including 10mm thick rendering in CM(1:4) complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10 mm thick polished, area of each tile 600mm x600mm on vertical surfaces as in skirting or dado set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 15 mm thick in cm 1:4 as backing complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10 mm thick polished, size of tile 600mmx 600mm in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed in cement mortar 1:6 complete all as specified and directed.

M&L 14-16mm thick Granite (of any type) work (table rubbed and polished) in cooking flatforms, window jambs and cills and like in CM 1:4 including pointing in white cement (1:2) using marble dust & pigment to match with shade of granite and rounding and polishing of edge complete all as specified and directed.

M&L for cement concrete Type D2 (1:4:8) (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for chequered cement concrete tiles 30cmx30cmx20mm thick set and jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15mm thick screed bed in CM(1:6) complete all as specified and directed.

Taking down wall panelling and similar work complete all as specified and directed.

S&F Solid PVC wall lining consisting of 5mm thick single side wood grain printed PVC Sheet inclusive of salvent cement and fixing at site on PVC frame as per specification complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification complete all as specified and directed.

S&F framed work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Pre-Painted steel windows & ventilators with glazed & wiremesh shutter with Guard bars. the frame and shutter section should be cut to length and miter joined with corner brackets made of Polypropylene. Mullion section should be joined using nut and bolts 4mm thick clear float glass to be provided using EPDM gasket all around glass incl all necessary accessories required complete all as specified and directed. Make : NCL Buildteck pvt ltd / TATA Pravesh / Elixir Met form Pvt Ltd / Ashish industries. Note : Net opening will be measured for payemnt purpose no extra payment will be made for glass or wiremesh.

Mild steel framed work such as in doors/chowkhats or gates of angle or other section with gusset plates, rail, braces etc. complete drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening & fixing and similar work conforming to Fe-290 grade E-165 complete all as specified, making good disturbed portion to match existing surface complete all as specified and directed.

S&F flush shutter 35 mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet & reinforced with MS square tube and fixing in opening as specification & drawing, complete all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded coloured PVC ’C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of single side prelaminated PVC sheet to be fitted in the MS frame welded/ sealed into the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification complete all as specified and directed.

S&F 200 mm stainless steel fancy handle of approved make fixed with SS screws etc. complete all as specified and directed.

S&F 200 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F 300 mm Stainless steel sliding door bolt with hasp and staple(bolt type) including fixing with necessary accessaries complete all as specified and directed.

S&F 75 mm long stainless steel door stopper of double legged with rubber shoes in bottom complete all as specified and directed.

S&F MS 125 mm Butt hinges, heavy weight, cold rolled mild steel fixed into MS frame for caging work etc throgh spot welding complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparation of new surfaces of wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

S&F mild steel plain black sheet 0.80 mm thick as in hearths,covering to door shutters , covering to door chowkat etc cut to size edges beaded if directed, holes punched, etc complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over and including a of coat zink chrome red oxide primer complete all as specified and directed.

S&F, stainless steel curtain rods of 25mm dia as in doors/ windows SS brackets fancy type, including screws and other necessary fitting(knob) for fixing brackets SS Funnels for 25 mm dia dropry rods, fixed at each end of rods complete all as specified and directed.

Dismantiling of loose concrete by chiselling from RCC members like col, beam, parapet, facia, ceiling and also remove any existing treatment on RCC surface by rubbing, scrapping etc exposing the reinforcement without disturbing the reinforcement and get free from rust by sand blasting providing at places addl reinforcement welding with existing reiforcement as directed wherever required binding with welded mesh 100 mmx100mm (12 gauge welded mesh) & tack welding and primed with using Araldite epoxy resins ( manufactured by M/s Ciba Geigy Ltd/ FAIR BOND EP/Sika or other approved manufacture) & provision of guniting pressure 2 to 3 Kg/Sqm with admixer 1 cement 3 sand mixed Dr fixit Pidicrete SC plasticiser (2 to 10% by weight of cement) of thickness 40mm average including stripping, floating with wooden strippers for proper dimension control inclusing necessary form work & scaffolding up to Three storey complete and surface of guniting to be finished fair and even with and including 10 mm thick plaster in cement mortar 1:4 with water proffing compound @3% by weight of cement, cleaning & removing of waste material etc as directed at site All surrounding wall, joineries and fitting should be covered with polythene sheet by contractor while work. (Any wall, floor,fittings and roof damaged by the contractor shall be repaired/change by contractor under same item and no extra payment will be paid to contractor on this account complete all as specified and directed. Note: Welded mesh & addl reinforcement if required measured and paid separately.

M&L for Mild steel TMT bar 6 mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally, binding wire (0.9mm dia annealed) for rebaring complete all as specified and directed.

M&L for welded steel wire fabric weight n exc 2 Kg/sqm complete all as specified and directed.

Dismantling of terracing tiles/brick tiles single layer on roof, laid bedded and pointed in any mortar complete all as specified and directed.

Demolition by using hand held electric drills, cutting machine, chisels etc (direct use of hammers on RCC roof for demolition is strcitly prohibited) of roof treatment including padding concrete of any description including mud in roof any thickness with and including roughening old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for cement concrete type B0 (1:2:4) (using 12.5 mm graded stone aggregate) as in padding and coping, incl hunching, benching etc complete all as specified and directed.

M&L for 10 mm thick in CM (1:3) rendering on fair faces concrete surfaces / roof top mixed with liquid water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note : Liquid WPC shall be measured and paid separately.

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for Preparation of plastered floor surface by cleaning surface free from dust and other foreign materials etc. and laying in repair Atatic poly propylene polymer modified membrane pre fabricated 3mm thick with non woven polyester matt central core of 160 gms/Sqm weighing not less than 3.5kg per sqm laid over primer conforming to IS 3384 @ 0.4 lit/sqm by using LPG/Butane torch and applying uniform pressure with a roller with overlap of 100mm in longitudinal direction and 150mm in transverse direction laid as per manufacturers instructions complete all as specified and directed.

M&L for cool roof ceramic tiles of size 300 x 300mm / 400 x 400 mm, thickness - 8mm of Approved shade, tiles should be anti-skid and have SRI value of more than 90 tiles should be laid on roof using tile adhesive of approved make as per manufacturers instructions complete all as specified and directed. Note : Cost of Tile adhesive shall deemed to be inclusive in the Item.

M&L for grouting using SC Apcorep Injection Grout LV grout.The detail procedure of inject grouting as under: (i) Drilling of 12mm dia holes upto 40mm depth and provide PVC nozzles/ entry ports over grid@ 1m c/c or less depending upon situation. (ii) Before injecting the grout compressed air to be blown to remove all dist and dirt. (iii) Grouting at pressure of 5kg/sqcm to be don till refusal/ rejection or appearance of grout from adjacent nozzle. (iv) Observe the cracks and make V groove along. (v) Nozzles and V groove shall be filled with polymer based mortar.

Removing of demolished meterial to a distance of exc 100m and n exc 200m or under, beyond the lead included in the rates, including loading, unloading complete all as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab as in flooring, steps of stair (treads), set with neat grey cement slurry @ 3Kg/Sqm, laid over and including 20mm thick cement and sand mortar (1:6) screed bed/bedding layer, jointed with grey cement slurry mixed with pigment to match the sahde of the slab including rubbing and polishing complete all as specified and directed

M&L for machine cut kota stone slab 18-20mm thick as in skirting/dado, riser of steps, laid over and including 10mm thick backing coat in CM (1:4), set in neat grey cement slurry @ 3Kg/Sqm, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path / plinth protection / sub base finished the surfaces even & fair complete all as specified and directed.

M&L preparation of new surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Supplying and Applying, two components acrylic polymer modified cementitious coating on new masonry surfaces devoid of plaster, with Hydrostatic resistance upto 5 bars with forced coverage of 1.75 Kg per Sqm in two coats using roller or brush with a gap of 4 to 6 hrs between the coats. The coats to be applied shall be perpendicular to each other complete all as specified and directed. Note : The Coverage is to be strictly maintained for film formation.

M&L for preparation of newly plastered surfaces of walls including cornices plaster etc and applying two coat oil bound distemper over and including a coat of primer & over applying a coat 1 mm of wall care putty on wall including rubbing with sand paper to achieve a smooth surface and sharp straight edges etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls applying a coat of 1mm thick wall care putty on wall including rubbing with sand paper to obtain a smooth surface and then applying two coats of exterior weather proof anti algae 100% acrylic emulsion over a coat of exterior water based primer complete all as specified and directed. (Make : Ist quality of approved make as specified).

Complete removal of any existing treatment and applying a coat of 1mm thick wall care putty on wall and rubbing the surface with sander to achieve a smooth surface and sharp straight edges etc.and applying two coats of oil bound distemper (any colour) complete all as specified and directed.

M&L for complete removal of existing treatment and applying a coat of 1mm thick wall care putty on walls and applying two coat of exterior weather proof anti algae paint over and including a coat of primer complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore including fittings of any type and material complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connection including removal of fittings of any type and material complete and all as specified and directed.

Cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring. etc. and making good, cutting not exceeding 10cm girth complete all as specified and directed.

S&F GI steel tubing 15mm bore medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F GI steel tubing 20mm bore medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repair 15mm bore bib tap long body, fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed. Cat No- HT F3001152 of Cera/ CON -107KN of Jaguar/ K-20073IN-4-CP of KOHLER or eqivalent make.

S&F repair 15mm bore angular stop valve chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Cat No - HT F3001201 OF CERA/ CON-053KN of Jaguar/ K-11568IN-7B-CP of KOHLER or equivalent make.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore PVC connection 600mm long heavy duty with brass fly nut and warsher for hot and cold water complete all as specified and directed.

S&F in repairs Ist quality vitreous china wash basin, white, flat back, size 550x400mm, PVC connections suitable for hot and cold water,bottle trap (with internal partition) 32 mm size with 300mm &190mm long wall connection pipes & wall flange, and fixing withbrackets/bolts including cutting and pinning in etc complete all as specified and directed.

S&F in repairs chromium plated shower rose 125mm size incl shower arm casted 190 mm long flat shape for wall mounted showers with flange incl fixing to steel pipe or union complete all as specified and directed.

Dismantling PVC water tanks and remove to store capacity exc 500 Ltrs and n exc 1000 Ltrs complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 litres capacity hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including float valve, Cover, GI nipple of suitable size complete all as specified and directed.

S&F in repair 25 mm dia Gun metal globe or gate valve with iron wheel head, screwd both ends for iron pipe complete all as specified and directed.

M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore dia iron pipe supplied and fixed in repairs complete all as specified and directed

S&F in repair Towel rail 20mm dia, 60cm long brass chromium plated with brackets complete all as specified and directed.

S&F in repair 10 ltrs capacity low level PVC dual flushing cistern, valveless, syphonic type, white,with inlet, ball float and handle including brackets complete and all as specified and directed.

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440 mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including S&F trap set complete all as specified and directed.

M&L Preparation of old steel painted surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and making good disturbed surfaces of walls, floor to match with existing specification complete all as specified and directed.

M&L for concealed point wiring for the following the PVC Insulated and unshether cable 1.5 sqmm (nominal area) multistranded copper conductor 1100 V FRLSH grade single core including PVC conduit medium grade of appropriate size (not less than 25 mm dia ) ISI MARKED concealed in wall and surface on ceilling complete with all accessories and all as specified including 1.5 sqmm PVC INSULATED unsheather multistranded copper conductor to common earth and concealed to earth dolly for following:- NOTE:-1.The cutting chases shall be finished with cement mortar (1:4) and surface of existing treatment without any extra cost. 2. Rate quoted by the contractor deemed to be included metal flush box of suitable size as required at site and 3mm thick laminated sheet suitable for mounting of switch and socket etc.

All as per item No 83.00 above but One light point controlled by one switch complete all as specified and directed.

All as per item No 83.00 above but One ceilling fan/exhaust fan control by one switch complete all as specified and directed.

All as per item No 83.00 above but One 3 pin socket outlet, 5 Amps independent complete all as specified and directed.

All as per item No 83.00 above but One 3 pin 5 amps socket outlet on the same board with other switches complete all as specified and directed.

All as per item No 83.00 above but One 3 pin 15 amps socket outlet independent but below the switch board of light board of light points in the same vertical plane complete all as specified and directed.

M&L For switch modular type 1 way 6 A ,1 module complete all as specified and directed.

M&L For switch modular type 1 way 16 A ,1 module complete all as specified and directed.

M&L for socket 6A- 2/3 pin combined 2 module complete all as specified and directed.

M&L for socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

M&L for ceiling rose surface bakelite 3 terminals complete all as specified and directed.

S&F Lamp holder insulated body with back plate for dome batten fittings complete all as specified and directed.

M&L for fan step regulator, 120W-2 moduler complete all as specified and directed.

M&L for white coverplate with frame, 2 module complete all as specified and directed.

M&L for white cover plate with frame, 3 module complete all as specified and directed.

M&L for white cover plate with frame, 8 module complete all as specified and directed.

M&L for white cover plate with frame, 12 module complete all as specified and directed.

M&L Metal flush box 2 module complete all as specified and directed.

M&L Metal flush box 3 module complete all as specified and directed.

M&L Metal flush box 8 module complete all as specified and directed.

M&L Metal flush box 12 module complete all as specified and directed.

S&F LED bulb of 9 watt, 240 V 50 Hz complete all as specified and directed.

S&F for energy efficient LED light fitting (2' X 2'size with tube 36 watt or minimum lumen output is not less than 3600 lumens ,230V recess mounting type including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

M&L in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 4 Sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 4.0 Sqmm as earth lead in & including concealed PVC conduit medium grade 25 mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification all as required at site complete all as specified and directed.

M&L in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 10 Sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 10 Sqmm as earth lead in & including concealed PVC conduit medium grade 25 mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification all as required at site complete all as specified and directed.

S&F VTPN distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar and neutral link, complete with one MCCB 4 pole 415 Volts 100 Amps,4 pole rating with rupturing cap 26 KA of the same make as of VTPN distribution board & with MCBs of required size making connection with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site complete all as specified and directed.

Supply and fix sheet metal enclosure MCB distribution board, 8 way double door with IP-43 IK-09 protection with metal door single phase 240 volts 8 way,including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB And making good distributed wall surfaces to match with existing specification complete all as specified and directed.

M&L for MCB single pole 240 volts 5 to 30 amps with rupturing capacity 10 KA using thimbles of required size complete all as specified and directed.

M&L for MCB single pole 240 volts 30 to 63 amps with rupturing capacity 10 KA using thimbles of required size complete all as specified and directed.

M&L for MCB single pole & neutral 240 volts 30 to 63 amps with rupturing capacity 10 KA using thimbles of required size complete all as specified and directed.

Disconnecting electrically, taking down existing OLD/UNSV ceilling/exhaust fan any type and capacity with due care ,dismantling blades and deposit to MES store for repairing with all accessories complete all as specified and directed.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30/45 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%,with remote for speed control and all remaining accessories including safety pin, nut bolts, washers, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete all as specified and directed. NOTE:-1. Additional down rod if required will be measured and paid separately. 2.T&P will be provided by the contractor for reaching any height of the bldg /warehouse/Hanger. 3.Writing MES number in black synthetic paint by the contractor.

Supply and fixing in repair surface and wall mounted LED Tube light & fitting 20 watts, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with provision PVC copper wire 1.5 sqmm 3 core of required length upto ceilling rose complete all as specified and directed.

Supply,Laying & testing of cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable 9 heavy duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed.

M&L GI Tubes, light grade, galvanised, with all fitting, laid in trenches 40MM complete all as specified and directed.

Supply and fixing LED street light fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver ,lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP 65/66 protection complete all as specified and directed.

Supply and fixing LED light fitting 1 X 16 watt flame proof, CMRI certified recommended for gas/vapor group of IIA &IIIB, Zone 1 & 2 and IP 65 Protection with die cast aluminium housing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size.

M&L for Earthing complete with galvanised iron earth plate electrode of size 600x600x6mm thick as earth electrode with top edge of the earth plate not less than 1.5mtr below ground level using GI wire 4mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of charcoal dust and salt all around the erth plate, earth work in any type of soil remaing surplus excavated material all as required at site and specified in EP No 5 of SSR part I 1991 or directed by Engineer-in-charge and testing on completion.

Please Enable Macros to View BoQ information