PROVISION OF SHED FOR POL STORE AT INAS 303, ADDN/ ALTN OF MAIN GATE AND PROVISION OF GUARD ROOM AT NTS UNDER GE (NW) VASCO

Amount

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard /dense soil complete all as specified and as directed

Excavation in trenches n,exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil complete all as specified and as directed

Material and labour for PCC 1:4:8 type D2(using 40mm graded aggregate)as in foundation filling and mass concrete etc.complete all as specified and as directed

Material and labour for re-inforced cement concrete 1:2:4 type B-1 (20mm graded aggregate) as in footings, including attached plaster and buttresses etc complete all as specified and as directed

Material and labour for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete all as specified and as directed.

Material and labour for re-inforced cement concrete M-30 (20mm graded aggregate) as in slab supported on wall, beams, plinth beams, Chajjas, roofs, landing, etc comp complete all as specified and as directed

Material and labour for RCC (Nominal Mix ) type B1, 1:2:4 (20mm graded aggregate) in columns, pillars, post and struts complete all as specified and as directed

Material and labour for MS TMT bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

Material and labour for MS TMT bars 5 mm dia and over, up to and including 10 mm dia in stirrups, spaces and binders complete all as specified and as directed

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete complete all as specified and as directed

Formwork to soffits of suspended slab such as roof slab, floor slab etc complete all as specified and as directed

Formwork to sides and soffits or arches complete all as specified and as directed

Material and labour for rendering 15 mm thick in CM 1:4 mixed with 3% integral water proofing compound and top surface finished to even & smooth w/o using extra cement complete all as specified and as directed. Note :- Integral water proofing compound will on concrete surfaces finished even and smooth without using extra cement .

Material and labour for rendering 15 mm in CM (1:6) over concrete wall surfaces finished even and smooth without using extra cement complete all as specified and as directed

Material and labour for preparation on newly plaster surface of walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over treated surfaces complete all as specified and as directed

Material and labour for preparation of newly plastered surfaces of walls and applying two coat of distemper over a coat of primer and 3mm thick wall care putty complete all as specified and directed complete all as specified and as directed

Material and labour for hard core of gauge n.exc 63mm, deposited, spread and leveled in layers nexc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed

Returning/filling in including spreading, leveling, watering and well ramming in hard/dense soil complete all as specified and as directed

Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point. complete all as specified and as directed

Material and labour for 100 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as cement concrete in Sub-base floors, and pavings finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed

Material and labour for 25 mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in floorings, as in sub base of floor tiles in ground floor complete all as specified and as directed

Material and labour for 15 mm thick screed bed in CM 1:4 for laying floor tiles complete all as specified and as directed

Material and labour for machine cut Kota stone slab 18-20 mm as in flooring etc laid over cement screed bed jointed with grey cement slurry mixed with pigment to match the shade the slab including rubbing and polishing complete all as specified and as directed

Material and labour for machine cut Kota stone slab 18-20 mm as in riser of steps, skirting ,dado and window cill etc laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade Including baking coat 10mm thick CM (1:4) and rubbing and polishing complete all as specified and as directed

Material and labour for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding .18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade complete all as specified and as directed

Material and labour for 350x250x7 mm/450x350x7mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. Including baking coat 10mm thick CM (1:4) comp complete all as specified and as directed

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet reinforced with MS square tube, fixed in position complete all as specified and as directed

Supply and fix factory made solid panel PVC door shutter plain sheet 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with prelaminated colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelaminated sheet PVC sheets for top rail, lock rain & bottom rail paneling of plain gap insert for top rail & bottom rail paneling of prelaminated PVC sheet 10mm to be fitted in the MS frame selded/sealed to the stiles & rails (stiles and rails feathered at edge) with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed

Supply and fix aluminium powder coated barrel tower bolts of extruded section 150 mm long complete all as specified and as directed

Supply and fix Aluminium alloy powder coated sliding door bolt 300 mm long with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed

Supply and fix stainless steel Butt hinge 100mm size complete all as specified and as directed.

Supply and fix extruded aluminium alloy, fabricated type handle, powder coated 150mm long complete all as specified and as directed.

Supply and fix in repair stainless steel wire mesh 0.36mm nominal dia of wire and avg width of aperture 1.4mm cut to size and fixed to doors/window shutters and fixed with aluminium wire staples as ordered.

Supply & Fixing Powder coated (minimum thickness of powder coated 50 micron) Aluminium anodised frame for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete architectural drawings complete all as specified and as directed Note: (a) Item shall be paid as per weight of aluminium section. b) The rate shall be inclusive of the locking arrangement including required builder hardware complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing surface area.

Supply & Fixing Powder coated Aluminium (minimum thickness of powder coating 50 micron) for shutters (opening/sliding) for doors, windows and ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved making conforming to IS 733 and IS 1285, fixing with dash fasteners of required dis and size, including necessary filling up the gaps at junctions i,e. at top , bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, CP brass/ stainless steel screw all complete as per architectural drawings complete all as specified and as directed Note: a) Glazing shall be measured separately. b) Item shall be paid as per D1 act weight of aluminium section. c) The rate quoted shall be inclusive of neoprene beading, glazing clips, screws, etc., as required which shall not be measured for arriving the weight. d) The rate shall be inclusive of the locking arrangement including required builder hardware complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing surface area.

Supply and fix Sheet pin headed figured glass ordinary quality ,4 mm thick and glazing with oil putty /wooden / metal beads in squares not exceeding 5 Sq m each complete all as specified and as directed

Material and labour for 18 mm thick both side plain solid PVC sheet suitably fixed in shelves, partition and shelves of built in cupboard almirahs book cases, cabinet boxes , racks, pelmet and similar work including all hardware fittings complete all as specified and as directed

S/F Vitreous china water closet European type with and including jet spray/faucet fixed including fixing in repair with P trap complete all as specified and as directed

Supply and fix vitreous china WHB, white, flat back, size 550mm x 400mm excluding taps, waste chain, and plug and porcelain stopper but including brackets complete all as specified and as directed

Supply and fix Bib tap cast copper alloy chromium plated long body fancy type screwed for CPVC pipe and fixed in repair 15mm bore complete all as specified and as directed

Supply and fix pillar taps, fancy type cast copper alloy, with capstan heads chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly-nuts, screwed for PVC pipe and fixed (15mm bore)all as specified and as directed

Supply and fix 15mm bore CP Angle stop valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

Supply only PVC low/high level flushing cistern, 10 Ltrs capacity including float valve, chain, PVC flush pipe all as specified and as directed.

Supply and fix CP grating doom 125mm dia with waste holes all as specified and as directed

Supply and fix PVC connections, 600mm long with brass CP/PTMT nuts suitable for connecting 15mm bore pipes, superior quality fixed in repairs. all as specified and as directed

Supply and fix CP shower roses 125mm size, with or without swivel joint including fixing to steel pipe, fixed in repair. all as specified and as directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth in stone concrete block or slab walls complete all as specified and as directed

Supplying & laying CPVC water tubing outer dia 20mm, SDR-11 grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed

Supply and fix towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and plastic cleats complete all as specified and as directed

Supply and fix curtain rails 25mm dia stainless steel with brackets stops rollers etc fixed in repairs complete all as specified and as directed

Supply and fix Mild steel roof trusses (framed), Trussesd, purlins, crane gantries, rails and framings and heavy bracket framing (Beam, tee, angle, channel or flat sections) confirming to Fe 410-W including cleats, distance pieces etc complete all as specified and as directed

Supply and fix pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having Tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed

Supply and fix pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ridge for roofing/roof gutter/wall, made to shape as required, fixed with self tapping screws as specified

Supply and fix 4mm thick sheet glass ordinary quality exceeding 0.5 sqm each pane complete all as specified and as directed

Supply and fix Glass shelf with Sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed

Supply and fix in PVC (SWR) floor trap 75 mm, plain with CP grating including joining with solvent cement complete all as specified and as directed

Providing 10mm thick plaster in CM (1:4) mixed with 3% integral water proofing compound over roof top surface finished to even & smooth w/o using extra cement complete all as specified and as directed. Note :- Integral water proofing compound will be measured and paid separately

Supply and fix PVC (SWR) WC connector with lip ring 110mm dia complete all as specified and as directed

Supply and fix 110 mm dia PVC (SWR) 'P' or 'S' trap complete all as specified and as directed

Supply and fix PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

Supply and fix PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to Floor complete all as specified and as directed

Supply and fix PVC (SWR) bends 110 mm bore of any radius provided with access door complete all as specified and as directed

Supply and fix PVC (SWR) vent cowl 110mm dia complete all as specified and as directed

Supplying & laying CPVC water tubing outer dia 16 mm, SDR-11 grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed

Material and labour for mild steel bolts (machine made) with hexagonal or square heads at one end and screwed the other ,or screwed both ends, each screwed end to be fitted with washer and one hexoganal or square nut, n exc 5cm long and diameter of neck 5 to 10 in mm complete all as specified and as directed

Material and labour for rendering 10 mm in CM (1:3) over concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed

Material and labour for newly plastered surfaces of Ceiling and applying two coats of White washing, over a coat of primer complete all as specified and directed.

Material and labour for cement concrete Type C-2,1:3:6 (20 mm graded aggregate) 75 mm thick as in plinth protection finishes even and fair without using extra cement finishing exposed edges fair for rounding and in phase every 2 mtr for length and joint shall be finished with bitumen and sand mixtures 1:3 complete all as specified and as directed.

Supply and fix PVC water storage tanks of 500 Ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed

Material and labour for Treating the bottom and sides of excavation at the rate of 5 ltr emulsion /Sqm of surface area complete all as specified and as directed

Supply only WPC

Material and labour for treating the backfill in contract with foundation at the rate of 7.5 Ltrs of emulsion per sqm of vertical surface area and side of internal beams etc complete all as specified and as directed

Material and labour for Treating the top surface of filled earth and under plinth protect at the rate of 5 ltr emulsion /Sqm of surface area complete all as specified and as directed

Material and labour for Preparing new surfaces of iron and steel and applying one coat of red oxide zinc chrome primer and two coats of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Soft/ disintegrated rock and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and as directed

Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed

Supply and fix tubular steel trusses including special shape washers etc. including for columns complete using ERW or induction butt welded tubes confirming to IS -1239 -1997 GRADE ST-240 complete all as specified and as directed

Supply and fix Pre- painted 3mm thick UPVC 3 Layer Roofing Sheets of any colour as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed

Supply and fix Pre- painted 3mm thick UPVC 3 Layer Roofing Sheets of any colour as in ridge , fixed with self tapping screws complete all as specified and as directed

Material and labour for preparation of steel surface and applying one coat of red oxide zinc chrome primer and two coats of Epoxy anticorrosive paint over 10 cm width or girth complete all as specified and as directed

M & L (150F) 150 mm wide 12.5 mm deep roll formed out of 0.5mm thick powder coated with 50 micron polyester powder paint on exposed side and coil coating with 20 micron outing on exposed side & 5 micron on rear side steel sheet as in false roofing with 34.5 mm wide x 48 mm deep made out of 0.6 mm thick steel sheet coated on both sides to hold panels in a module of 150 mm. Carrier to be spaced at 1.7 mtr c/c without insulation & 1.5 mtr c/c with insulation Suspension of frame work by means of 4mm dia galvanised steel wire rod hanger and spring steel suspension clip fixed to roof by J hooks and nylon inserts. Suspension to be spaced at 1.5 mte c/c without insulation & 1.3 mtr c/c with insulation and exterior side suspension by means of GI suspension clit at desired c/c spacing complete. complete all as specified and as directed

Supply and fix 3mm thick Aluminium composite panel coloured (as approved by GE/EIC) including aluminium frame work with aluminium section of size 25 mm wide at 50cm c/c on vertical and horizontal for panel fixing with double tap and joints filled with silicon on wall/column/facia etc complete all as specified and directed.

Dismantling mild steel work of any description not otherwise provided for complete all as specified and as directed

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed

Excavation in trenches n. exc 1.5 M wide & n. exc 1.5 M in depth for foundation in soft/disintegrated rock and getting out complete all as specified and as directed

Material and labour for concrete bed to drain pipe and including packing under haunching against the sides & pipe and after they laid and tested in cement concrete 1:4:8 type D2 bore of pipe 150 mm dia complete all as specified and as directed

Supplying and laying of UPVC pipe bearing ISI mark, 150 mm dia heavy duty minimum including jointing with coupler complete laid in trenches or floors complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required internal dia of pipe 150mm complete all as specified and directed.

Material and labour for Pre - cast cement concrete block masonry type C1 1:3:6 (20mm graded stone aggregate) with solid blocks, exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Material and labour for precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate for cover slab for MH/Septic tank set in CM 1:4 including formwork complete all as specified and as directed.

Material and labour for 8 mm dia TMT bar cut to length, bend to shape required including cranking bending & hooking ends & binding with MS wire annealed n. less 0.9mm dia complete all as specified and as directed

Material and labour for providing, cement concrete type B1 ,1:2:4 using 20 mm graded stone aggregate in haunching, roof kerbs or mud stops, rounded or chamfered on edges all as specified.

Material and labour for 100 mm thick cement concrete type C2, 1:3:6 using 40 mm graded stone aggregate in sub base of flooring/ hard standing complete all as specified and as directed

Supply and fix Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed

Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed

Providing cement concrete type B1 1:2:4 (20mm graded stone aggregate) in kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed

Supply, laying GI Tube medium grade 40 mm size dia in repairs including all fitting complete all as specified and directed

Supply, laying GI Tube medium grade 25 mm size dia in repairs including all fitting complete all as specified and directed

Excavation in trenches by cutting of road crossing/PCC hard standing, under boundary wall for laying of pipe/cable including making good the existing surface with same finish to match the original finish complete all as specified and as directed

Supply and fix Gun-metal gate valves 40 mm bore size, ISI Marked, as per IS:778, complete all as specified and directed

Supply and fix Gun-metal gate valves 25 mm bore size, ISI Marked, as per IS:778, complete all as specified and directed

Material and labour for single phase 1 HP motor 230 volt,50 Hz complete all as specified and as directed

Construction of valve pit brick masonry ,internal size not less than 900x900x600 mm (from top of PCC to bottom of cover ) including excavation in any type of soil returning, filling around foundation are removal of surplus soil to a distance not exceeding 50 mtr PCC 1:4:8 type D2 in foundation brick work in cement mortar 1:6 ,10 mm thick plaster in cement mortar 1:4 to internal surface covered pit with MS sheet cover 3 mm thick with locking arrangement handle fixing arrangement and painting with oil paint two coat over a coat of red oxide primer all as specified and directed

Supply and fix PVC (SWR) bends of 110mm radius complete all as specified and as directed

Supply & fixed PVC 1/2 rounded gutters of 30cm with union sockets to joints set in approved jointing compound complete all as specified and as directed

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed

Material and labour for Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) 75mm thick as in sub base of flooring/plinth protection complete all as specified and as directed

Material and labour for preparation of new plastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm all as specified and as directed complete all as specified and as directed

Material and labour for cutting and racking out joints of size 30 mm x 15 mm with cutter and cleaning with blower and making sides of joints bitumen free sealent of approved make High performance, cross linked, closed cell, on-absorbent, polyethylene joint fi ller, then filling the top gap with polyurethane based sealant of approved make over a coat primer including bond breaker caulked tightly into base of sealing groove complete all as per manufacturers instructions complete all as specified and as directed

Supply and fix embossed translucent polycarbonate skylight corrugated sheet of 2 mm thickness as in roof covering, fixed with self tapping screws all as specified and directed

Supply and fix prefabricated crimp curved galvanized roof sheet (colour coated) of required thickness(0.40 mm to 0.80 mm as in roof covering, fixed with self tapping screws and to match with existing cladding and roof sheet complete all as specified and as directed

Supply and fix in repairs Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: with bevel gear box and crank handle 1.25mm thick complete all as specified and as directed

Material and labour for Aluminium powder coated (powder coated of required colour) three track sliding windows frame top & sides of size 92x31.75x1.50mm , bottom size 92x31.75x1.50mm and shutter top & bottom of size 40x18x1.55mm and sides (handle) of size 40x18x1.55mm and lock side shutter frame of size 40x18x1.45mm with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick frosted/pinheaded glass with necessary rubber beading gasket complete all as specified and as directed

Material and labour for demolition of cement concrete of any description and in any position not otherwise specially provided for and demolition procedure like cutting out of full depth of (100 to 450mm) existing damaged/shattered concrete slab with diamond wheel cutter or carbide tipped wheel saw to provide a pressure relief cut within the patch area prior to boundary sawing, in proper rectangular, square or triangular shape perimeter without disturbing adjacent slab, after the repair area is isolated by full - depth saw cuts, making small pieces, lift and removing the deteriorated concrete slab pieces from its position and removing to a distance exc 1.0 Km and not exceeding 5 Km complete all as specified and as directed

Material and labour for laying dry lean concrete (DLC) of aggregate gradation as per Table 1 of SP 49:2014 having 7 days average compressive strength not less than 7 Mpa. Minimum cement content not less than 140 Kg/Cum DLC mixed in batching plant, transported to site and laid by electronic sensor paver including spreading and compacting using high amplitude tamping bars of paver (initial compaction) further by double drum smooth wheeled vibratory rollers with 80-100 KN static weight to achieve minimum dry density, necessary finishing etc complete all as per specified and tolerances to be as per table 900-1 of Morth specifications for road and bridge work 2013 complete all as specified and as directed

Supplying and laying 400 micron thick HDPE Sheet (Virgin quality|) water proof, wrinkle free without puncture having minimum weight 390gm/Sqm over tack coat/Sand cushion as specified in the design with overlap between adjacent strips and at transverse joints as minimum 300mm complete all as specified and as directed by Engr-in-Charge. Note: Sand layer shall be measured and paid separately and overlapping of HDPE sheet shall be included in this unit rate complete all as specified and as directed

Pavement quality concrete (PQC) of minimum 28 days field Flexural strength of 45Kg/ Sqcm or 4.5 Mpa, aggregate gradation as per Table 3 of IRC 15-2017, coarse aggregate of clean, hard strong, dense, non-porous and durable pieces of crushed stone or gravel, fine aggregates of clean natural sand or crushed stone sand or combination of both using minimum 400 Kg/Cum of cement with non-circular, virgin synthetic fibre of 12-18 mm length, specific gravity 1.34 to 1.39. UV stable, alkali resistant, with equivalent dia 15-40 micron, minimum melting temperature as 240 C and minimum tensile strength of 300 Mpa and at the rate specified by the manufacturer. PQC laid, spread and compacted with slip-form paver of minimum 7.50 m width, including curing and tinning by texturing cum curing machine complete all as per specified and directed. Required surface texturing to be done as specified in clause 10.1, 14 and Table 9 of IRC 15-2017.

Supply only non circular synthetic fiber reinforcement all as manufacturer instructions complete all as specified and directed.

Finishing surface of concrete roads, pavements, by brooming complete all as specified

Forming 25 mm width expansion joint in concrete slab for full depth of PQC. Early entry saw and subsequent cutting by using diamond bit cutter of appropriate size, straight and smooth edges. Joint cleaned thoroughly with application of compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris. The joint then filled with the remolded 25mm thick compressible polyethylene closed cell type filler board as specified, thereafter application of two coats of primer with thin brush by forward and backward movement at an interval of 30 mins before placing the backup rod and pouring the sealent. Placing of closed cell, medium density, crossed link polyethylene foam pickup rod of 30mm dia, over filler board and filled with polyurethane based sealent complying with BS- 5212, BS-4254 & EN-141875-2003 with minimum movement accommodation factor (MAF) of +/- 30% having minimum 10 year performance guarantee, applying masked tape after filling of sealent as per the method specified by the manufacturer complete as specified and as directed. Note : (i) Initial cutting shall be carried out within 24-36 hours of casting. (ii) Final cutting, rounding of edges, use and waste of back up rod to avoid deposition of foregoing materials in the joint up to final filling of joints shall be carried out after 28 days complete all as specified and as directed

Material and labour for use and waste of formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Fair finished surfaces of concrete flat complete all as specified and as directed

Material and labour for use and waste of formwork to sides of pillars, posts, struts, piers, columns, and stanchions Rough finished surfaces of concrete Circular on plan complete all as specified and as directed

Material and labour for RCC M-30 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and as directed

Material and labour for RCC M-30 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed

Material and labour for Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded aggregate) as Foundation beams, plinth beams, bases for columns etc complete all as specified and as directed

Surface dressing n exc 15cm deep and getting out in soft/loose soil complete all as specified and as directed

Material and labour for RCC M-30 ( Design mix) (using 20mm graded aggregated) as in foundations, footings, foundation beams , plinth beams, bases for columns etc basement slabs under reamed piles and mass concrete etc complete all as specified and as directed

Material and labour for RCC M-30 ( Design mix) (using 20mm graded aggregated) as in chajjas etc complete all as specified and as directed

Material and labour for spreading, leveling and well ramming including watering required in layers n exc 25 cm thick complete all as specified and directed

Material and labour for 75 mm thick PCC 1:2:4 type B1 (20mm graded aggregate) as in ramp flooring etc and finish the surface even and fair complete all as specified and directed

M/L for rendering 15 mm thick in CM 1:6 on brick walls finishing with even and smooth (with out using extra cement)etc complete all as specified and directed

M & L rendering 5 mm thick in CM 1:3 on ceiling surfaces finishing with even and smooth (with out using extra cement)etc complete all as specified and directed

Material and labour for 20 mm thick screed bed or bedding layer of mortar for laying floor finishes CM 1:4.complete all as specified and directed

Supply and fix MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, ladders; framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed

Material and labour for Rendering 10mm thick in CM(1:3) on cement concrete surfaces on the top of roof surfaces with water proofing compound to receive water proofing treatment all as per manufacturer instructions complete all as specified and as directed.(Note :-WPC will be measured and paid separately.

Material and labour for applying evenly & priming with oil bound bituminous primer at 0.4Ltr per sqm for water proofing treatment complete all as specified and as directed

Material and labour for APP based polymeric membrane minimum weighing 3Kg/sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed

Material and labour for Machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 10mm thick 1:4 in CM in vertical surface complete all as specified and directed.

Material and labour for preparation of new steel surfaces over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of primer red oxide, zinc chrome

Material and labour for preparation of new plastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm all as specified and as directed.

Material and labour for Preparing new plastered wall surfaces and applying two coat of oil bound distemper over chalk whiting, on plastered surfaces, preparatory to distempering, after applying 3mm thick wall care putty on wall

Material and labour for preparation of new surfaces of ceiling and applying three coats of white wash all as directed

Supply and fix 1.60mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Supply and fix Mild steel sliding door bolts 375mm long, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed

Supply and fix size Butt hinges, heavy weight, cold rolled mild steel size 125 mm long complete all as specified and as directed

Supply and fix Powder coated aluminium grill of design DG-104 pattern, made out of 10mm dia rod fixed with and including standed aluminium frame of 'F' section of size 23.4x15.3x1.4 mm thick all as per manufacturer's instructions complete all as specified and directed

Material and labour for one point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 1.5 Sq mm single core, including one No. 1.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LSH as continuous earth wire drawn in and including PVC conduit medium grade of as required size (not less than 20 mm in width) ISI marked medium grade with all accessories of same grade fixed concealed in wall including provision of modular metal flush box, modular cover plate with frame top cover for housing switch, socket, fan regulators etc for one light point controlled by one 5 Amp switch one way complete all as specified and as directed

All as per item No 148 here in before, but for one fan/exhaust fan point controlled by one 5 Amp switch one way complete all as specified and as directed

All as per item No 148 here in before, but for one 3/5 Pin, 5 Amp Switch socket out let on the independent board complete all as specified and as directed

Material and labour for surface point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 2.5 Sq mm single core, including one No. 2.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LSH as continuous earth wire drawn in and including PVC conduit medium grade of as required size (not less than 20 mm in width) ISI marked medium duty, with all accessories of same grade, fixed concealed in wall including provision of modular metal flush box, modular cover plate with frame top cover for housing mounting switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type on the independent board complete all as specified and as directed

Material and labour for sub main wiring with two runs of single core 6 Sqmm FRLS Copper conductor PVC insulated unsheathed cable as per IS 694-1990 (third revision) drawn through & including non metallic rigid PVC conduit medium grade of as required size (not less than 20 mm in bore) with all accessories such as Tees, elbows, junction boxes etc, as required fixed concealed in wall along with one run of 6 Sqmm single core FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board/ distribution board and testing on completion etc complete all as directed. (Note :- two runs of cable, one run of earth continuity conductor and one run of PVC casing capping/conduit shall be measured as one unit)

Supply and fix modular Switch single pole one way 6 A, 240 V complete all as specified and as directed

Supply and fix modular Switch single pole one way 16 A, 240 V complete all as specified and as directed

Supply and fix Modular Socket outlet 2 in 1, 6 Amp , 240 volts, complete all as specified and as directed

Supply and fix Modular Socket outlet 5A/16A, 5 in 1, 3 pin, flush type universal, 240 volts complete all as specified and as directed

Supply and fix Ceiling rose, surface bakelite, 65 x 50 mm two/ three terminals 240 volts complete all as specified and as directed

Supply and fix Fan step regulator, 120W - 2 module all as directed.

Supply and fix MCB DB SPN 12 way DB 230 V with 200 A rated bus bar double door type complete all as specified and as directed.

Supply and fix MCB SPN 06 -32 amps 230 volts C curve, 50 HZ AC 10 KA complete all as specified and as directed

Supply and fix MCB SP 06 to 32 amps 230 volts C curve, 50 HZ AC 10 KA complete all as specified and as directed

Material and labour for Earthing complete with Galvanised earth plate electrode 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth wire 4 mm dia by mean of nuts/bolts, check nuts and washers of brass as shown in electrical plate No. 5 of SSR part-I including necessary excavation and earth work, GI Pipe 15 mm bore light grade for watering with Funnel, wire mesh and protection to earth lead shall be provided with GI pipe light grade 20 mm dia up to 7.5 mtr from the earth plate electrode and refilling of soil including adequate quantity of charcoal dust and common salt etc & earth work in any strata, PCC pit chamber in cement mortar 1:3:6 type C-2 with 40 mm thick Precast RCC cover slab 1:2:4 type B with 8 mm dia TMT bar and handle with lifting hooks including testing any type complete all as specified and as directed.

Material and labour for ceiling fan 1200 mm sweep complete body 230 volt ,50 Hz

Supply and fix recesses/surface mounting lights 2'X2' LED flat panel 36 Watt, white powder coated CRCA housing with high-power LEDs , aluminium front frame with flat white high transmission acrylic cover, internally prewired, 230V,complete with all accessories such as electronic driver, LED strip, connector block etc.and necessary fixing arrangement at any height and removing old unserviceable item complete all as specified and directed.

Supply and fix LED post top light/gate light with die cast aluminium body and with white powder coated aluminium reflector and IP-65 protection of 40 watts capacity all as directed.

Supply and fix LT junction box suitable for 1100 Volt grade outdoor type, single door, pedestal mounted, overall size not less than 450 x 450 x 450 mm, having aluminium bus bar of 400 A capacity - 04 Nos with necessary hole for connection of LT cables mounted on suitable strength epoxy insulator 1100 KV grade -12 Nos in width wise, dust and vermin proof & lockable, factory made, fabricated out of 3 mm thick CRCA sheet suitable for 3 Phase 4 white system, duly insulated with heat shrinkable type coloured sleeve, supported on suitable size "C" Channel in the vertical position - 03 Nos, LT danger notice board fixed on door on both side, with independent plates at bottom for each out going and in coming cables in cable alley and painted with powder coating in Siemens grey colour and including Angle iron base frame as reqd size as per above panel, total leg height 600 mm and grouting in side PCC 150 mm legs and made out of ISA 4040, 40 x 40 x 6 mm thick angle iron duly painted all as approved and as directed.

Material and labour for LED Tube light fitting, 1x 20 watts. Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body, environmental friendly, energy efficient ready to use pack complete rewired, Premium 20 W LED batten, connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450MM sweep with, blades, and frame and louvers complete all as specified and directed..

Supply & fix Air Circulator fan steel body, 230 volts single phase oscillating 450 mm sweep suitable for wall mounting with suitable RPM all as specified and directed.

Material and labour for sheet metal enclosure MCB distribution board, double door single pole and neutral with IP-66 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair all as specified and directed. (Note:- MCBs will be measured separately.)

Material and labour for MCB single pole and neutral 240 volts any rating from 40 to 63 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

Flame proof point wiring complete with 2.5 sqmm single core PVC insulated, unsheathed FRLS cable 1100 volts grade, multi stranded with copper conductor drawn through and including ERW steel conduit with conduit accessories i.e.. flame proof bends, flame proof junction boxed etc including 2.5 sqmm PVC insulated, unsheathed FRLS copper conductor multi stranded cable 1100 V grade as earth continuity conductor & connecting to common earth dolly all as specified for one flame proof light/fan/switch socket combined point controlled by one switch complete all as specified and as directed Note: No joints in cables will be allowed in flame proof wiring)

Supply and fix for switch flame proof rotary type with termination box in LM6, 6/16A, single pole 250V of IP 66 rating complete all as specified and as directed

Supply and fix for flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V all as specified and directed.

Supply and fixing LED light fitting 1x30 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass, with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size all as specified and directed by Engr-in-Charge.

Supply and fix flameproof exhaust fan of size 12 inch sweep, suitable RPM, single phase consisting of not less than 0.25 HP motor complete all as specified and directed by Engr-in-Charge.

Supply and fix LED street light fitting 60 watts, made in pressure die cast housing with epoxy power coated dark graphite grey colour finish. Prismatic polycarbonate cover with individual LED lenses with IP 66 complete with all accessories and necessary fixing arrangement on wall at any height including three core 0.5 sqmm copper cable from connector to fitting complete all as specified and directed by Engr-in-charge.

Material and labour for flameproof distribution board panel single pole and neutral, 6 way inclusive of SPN 32 Amp incomer and outgoing MCB SP of 6-20 amps 04-Nos for 230 volts, 50Hz and required nos of cable entries as bottom wall mounting frame along with cable glands with anti corrosive epoxy powder coated, hardware in stainless steel with protection IP-65 equipment standard as per IS, approved by CCE and certified by CMRI complete all as specified and directed. Note: The rate quoted to be inclusive of brackets made of MS steel of suitable size for the above fittings complete all as specified and as directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core complete all as specified and as directed

Supply and lay Double walled corrugated pipe (DWC ), heavy duty 63/50 mm bore for cable protection as a guard pipe including required accessories etc. complete as specified and directed.

M/s VEEJEE ENTERPRISES (BID ID -3394505)

K M SUBHANAIAH (BID ID -3402929)

M/S P S BABU (BID ID -3403237)

M/S G.N.POWAR (BID ID -3402765)

AURA ENTERPRISES (BID ID -3394961)