Repair/Rehabilitation of various aminities at PH RPM-1 at Km 5.800 Rampura Sub Minor.

Amount

Scraping of cement plaster (HSR item No. 8.32-c)

Plastering on walls 12 mm thick cement plaster 1:3 (HSR item No. 15.4)

Cement pointing 1:3 deep variety on brick wall (HSR item No.15.61)

Supply and fixing trapezoidal/corrugated sheeting system in galvalume in colour coating steel at least covered width of 1000 mm corrugation sheet be made from base metal having 0.8mm thickness in steel of grade 345 as per ASTMA 792 M coated with alloy of AI & Zn to grade AZ minimum alloy mass 150 gm/Sqm total, both side with colour coating having complete dip tank pre-treatment process with chromat conversion (Cr+3) as main pre-treatment followed by PU primer of min. 5 micron DFT on each surface, finished with special polyester paint to grade 20 of min. 20 micron DFT on exposed surface and 5 micron in grey shad on unexposed surface. Fixing of above sheets with necessary self drilling & self trapping screws/bolts & nuts. EPDM washers with 150 mm laps where ever required. Make : TATA/JINDAL JSW/BIRLA HIL/ESSAR. Note : 1- The rates shall include costs of fixture like SD/self trapping screws with EPDM washers incl. Stitching as required incomplete line and level inclusive lifting to all heights as required .

First class brick laid in cement sand mortar 1:4 in foundation and plinth. (HSR item No. 11.4)

Finishing of wall with apex paint 2 Coats 1st Quality(HSR item No. 16.79)

Scraping of Snocem on exterior walls (HSR item No. 8.32-a)

White washing 2 Coats over interior walls(HSR item No. 16.47)

Apply 2 Coat of Snocem on retaining wall of PH(HSR item No. 16.61)

P&F gauge patti at U/S & D/S of PH (NS item)

Preparation of plastered or concrete surface for painting including sand papering etc.(HSR item No. 16.24)

Borders and arrow upto 6cm in width main Pump House (HSR item No. 16.66-c)

Painting 2 coat with ready mixed exterior paint in all shades on newly plastered/conc. surface (HSR item No. 16.26)

Repainting letters and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade English and Roman (Hyphons and the like not to be measured and paid for). (HSR item No. 16.67-b)

Wrought Iron & mild Steel ledders, grilles, frames, doors openable or fixed or any other type of railing, gates entry guard i/c cost of screw welding rods bolt and nuts complete fixed in position (HSR item No. 18.12)

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR item No. 6.6)

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in F&P (HSR item No. 10.39)

Laying 1st class brick masonary in Cement sand mortar 1:6 in F&P (HSR item No. 11.2)

Damp proof course 40 mm thick of cement concrete 1:2:4 using stone aggregate 20mm nominal size with 2 coats of bitumen 20/30 penetration, at 1.65 Kg per sqm laid hot and sanded.(HSR item No. 10.114)

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level. (HSR item No. 11.7)

Laying RCC Slab 1:1.5:3 including C & S (HSR item No. 10.82+10.95-a)

Cold twisted deformed (ribbed/ or steel) bars for R.C.C. works, where not included in the complete rate of R.C.C. including bending, binding and placing in position complete. (HSR item No. 18.22)

Laying Cement Plaster 12mm thick in CM 1:5. (HSR item No. 15.6)

Plastering on walls 15 mm thick cement plaster 1:5 on the rough side of single or half brick wall (HSR item No. 15.11)

Laying cement plaster 10mm thick CM 1:3 (HSR item No. 15.51)

Terracing consisting of tiles 22.86 cm X 11.43cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR item No. 13.13)

Laying CC 1:2:4 for Gola 4"x4" (HSR item No. 13.64)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16 (HSR item No. 13.50)

Bottom khurra on ground 1:2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR item No. 13.57)

Providing & fixing PVC rain water pipe 6Kg pressure of ISI mark in cement mortar during masonry work 100mm dia for toilet at PH NB-5 (HSR item No. 13.89-a)

Providing & Fixing PVC bend ISI mark 100mm dia at PH NB-5 (HSR item No. 13.90-a)

Base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling. (HSR item No. 14.1)

Cement Concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth. (HSR item No. 10.41)

Providing & Fixing ceramic tiles/and skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (HSR item No. 14.91)

Providing & fixing 1st quality ceramic glazed wall tiles size 200mmx300mm confirming to IS 15622 (thickness to be specified by the manufacture) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by EIC in skirting riser of steps and dados over 12mm thick bed of cement mortar 1:3 coarse & jointed with grey cement slurry i/c pointing in white cement mixed with pigment of matching shades complete (HSR item No. 14.92-a)

P&F HDPE water tank of capacity 500 Ltr. (HSR item No. 30.119)

Applying 3 coat of white washing on walls inner face (HSR item No. 16.48)

First class 11.43 cm thick honey-comb brick laid in cement sand mortar 1:4 (HSR item No. 11.91)

Supplying boulder in bed of septic well bricks bats As per credit of brick bats rate.

P&F in position best indian make indian type water closet suite (HSR item No. 30.2-b(i))

P&F PVC pipe fitting for toilet & bath (M.R.)

Wiring 1.5mm sq. PVC insulated copper conductor cable in 1.5mm conduit pipe for short light point (HSR item No. 31.1-a (ii))

Supply and erection of PVC sheathed Aluminium conductor cable single core 1100 volts grade in pipe etc., of suitable size excluding cost and erection or pipe (HSR item No. 31.11(v))

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement (HSR item No. 8.5-b)

Damp proof course 25 mm thick of cement concrete 1:2:4 using stone aggregate 20mm nominal size with 2 coats of bitumen 20/30 penetration, at 1.65 Kg per sqm laid hot and sanded. (HSR Item No. 10.115)

First class brick laid in cement sand mortar 1:5 in F&P. (HSR Item No. 11.3)

First class brickwork laid in cement sand mortar 1:5 in first storey upto 4 meters above plinth level. (HSR item No. 11.8)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects. (HSR Item No. 10.82)

Conglomerate floor 25 mm thick cement concrete 1:2:4 on 100 mm cement concrete 1:8:16 and 100 mm sand or stone filling.(HSR item No. 14.13)

Plastering on walls 15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR Item No. 15.10)

Providing and fixing fan hooks 80 cm long, of required shape and size12 mm dia (HSR Item No. 18.38-b)

Providing and fixing cast iron rain water non pressure pipe, I.S.I mark with ears with screw and wooden plugs fixed on wall face including filling joints with spun-yarn and cement mortar 1: 2 excluding head and shoe, etc. 100 mm dia pipe (HSR Item No. 13.45-a)

Providing and fixing cast iron shoe for 100mm dia rain water pipe on wooden plugs,fixed on wall face including filling the joints with spun yarn and cement mortar 1:2(HSR Item No. 13.48)

Providing and fixing M.S. angle and T-iron frames for door, window and ventilator including iron hold fast, butt hinges of I.S.I. mark fixed in position with machine screws and duly welded including all other suitable locking arrangements provided and welded with the frame and making holes and Quintal 120.00 1069.70 fixing glazing clips in the frame, filing the welds and finished with a coat of red lead non setting primer complete in all respects. (HSR Item No. 18.35)

Commercial hard wood such as hollock, champ, chikrassy and chaplash, etc., (nonconiferous timber other than teak conforming to I.S. specification No.1003 kiln seasoned),shutters with vertical styles and rails, as specified in the statement No.1 (attached in the end of this chapter), with two Nos. plywood panels of the specified thickness,mentioned below, tongued and grooved including the cost of iron hinges, screws, chocks/cleats, stops, etc., complete fixed in position excluding the cost of tower bolts and handles but including the labour for fixing the same 35 mm thick (12 mm thick commercial plywood panel). (HSR Item No. 17.30-c)

Cost of iron fittings, complete for doors and windows,such as tower bolts,handles,etc., and screws for these fittings (excluding sliding bolt) for single leaf shutter (HSR Item No. 17.71-a)

Cost of iron fittings, complete for doors and windows,such as tower bolts,handles,etc., and screws for these fittings (excluding sliding bolt) for double leaf shutter (HSR Item No. 17.71-b)

P&F sliding bolt with nuts and screw of size iron 300mm x16mm (HSR Item No. 17.83-C)

Precast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in tiles and channels and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete at the ground level or in first storey. (HSR item No. 10.78)

Cement Concrete 1:2:4 with stone aggregate 20mm nominal size in first storey upto 4 meters above plinth level. (HSR item No. 10.59)

Painting 2 Coat with ready mixed paint on matallic surface in all shade on old sheets/iron work.(HSR item No. 16.18)

Painting two coats excluding priming coat with ready mixed paint for mattalic surface in all shades on new steel or iron work (HSR item 16.17)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW DOWN CISTERN flush bend and all other necessary fittings instead of 12.5 litres capacity high level C.I. high level flushing cistern with flush pipe IN WHITE ENAMEL SPRAY PAINT after making smooth the C.I. surface by rubbing, scrapping etc., complete (HSR item No. 30.10)

PROVIDING AND FIXING IN POSITION ON BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TAP FOR LAVATORY SUITE (HSR item No. 30.45)

P&F wash basin without pedestal (Market rate)

CONSTRUCTION of INSPECTION CHAMBER in BRICK MASONRY of Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab) UPTO 0.60 METRE AVERAGE DEPTH in cement mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 BENCHING 12mm THICK CEMENT PLASTER 1:2 with a floating coat of 1mm thick of neat cement R.C.C.1:2:4 SLAB 100mm THICK /C.C.TOPPING 50 mm THICK WITH 455 MMx455 MM/455MMx610MM INSIDE LIGHT DUTY C.I.INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design (HSR item No. 29.84-c)

P&F ventilator with MS Jali (N.S. item)

Dismenteling GI sheet for roof (HSR item No. 8.11)

P&F Electric fitting L.S (Ward & Watch)

P/F M.S angle 50x50x6mm in CC pits (HSR item No.18.1-c)

P/F GI barbed wire fencing (hot deep) 2mm thick(N.S item)

Applying priming coat with metal primer on new steel or iron work including preparation of surface(HSR item No. 16.9)

Wiring in 1.5mm PVC insulated copper conductor cable in 1.6mm thick conduit pipe short light point.(HSR item No. 31.37(ii)(a))

Wiring in 1.5mm PVC insulated copper conductor cable in 1.6mm thick conduit pipe Fan point.(HSR item No. 31.37(i)(b))

Wiring in 1.5mm PVC insulated copper conductor cable in 1.6mm thick conduit pipe 3 Pin 5 Amp plug Point.(HSR item No. 31.37(vii)(c))

Supply & erection of sheet steel enclosure distribution Board suitable For MCB’set. Distribution board 4 way. (HSR item No. 31.12(d)(iv)