GE 874/EWS-35/2019-20

Amount

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in any type of soil, complete all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in any type of soil, complete all as specified & directed.

Excavation in post holes each not exceeding 0.5 cum getting out, returning, filling in, including spreading, leveling, watering and well ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, in any type of soil, complete all as specified.

Mild steel work as in hand rails, half round or other stock section or core for wooden hand -rail, straight portion drilled and countrsunk for ballusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cuttings, tops to shapes, as directed, drilling, holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 all as specified.

Supply only chain link fencing any size for standards, rails, straining bolts, etc. including provision of binding wire complete as specified and directed.

Fixing only chain link fencing including line wire including cranking, bending ends any mesh size and type of standard, rails straining bolts etc including provision of binding wire.

Supply only Mild steel Round bars conforming to Gde-I,IS-432 (Part I) 10mm dia for fixing of wire mesh complete all as specified & directed.

Galvanised, 2 strand steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing and tying at crossings with and provision of galvanized mild steel wire, staple or steel pins, etc complete all as specified and directed.

M & L MS screw bolt diameter of shank 11 to 15mm (machine made ) with hexoganal head at one end screwed the other or screwed both ends each screw end fitted with washers and one hexagonal nut, exe 05cm not exe 10cm complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundations filling and mass concrete, complete all as specified.

M&L 100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 in foundation, filling and mass concrete (using 40 mm graded crushed stone aggregates) as in foundation and mass concreting all as specified directed.

Walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

Brick work with subclass ‘B’ Modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified and directed

M&L 100mm thick PCC 1:2:4 type D-2 (using 20mm graded crushed stone aggregates) as in hardstanding, laid in panels and finishing the surface even and fair without using extra cement including use of formwork and making joints and rounding or chamfering exposed edges complete all as specified and directed.

M&L finishing surface of concrete pavements by brooming with mild steel wire brush complete all as specified and directed.

Forming Contraction (Dummy)joints 100mm deep x 10mm wide,filled with sealing compound Grade A complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material to a distance not exc.50 m and depositing where directed at a level not exceeding 1.5 mtr above starting point, complete all as specified and directed

RCC M-25 Design Mix, (using 20mm graded crushed stone aggregates), as in foundations including raft, foundation beam, plinth beam etc, complete all as specified & directed by Engr-in-Charge

RCC M-25 Design Mix, (using 20mm graded crushed stone aggregates), as in beams, cantilevers, bressummers, lintel over 1.5 mtr span, complete all as specified & directed by Engr-in-Charge.

RCC M-25 Design Mix, (using 20mm graded crushed stone aggregate), as in columns, pillars, piers, posts and struts complete all as specified and directed, complete all as specified.

Form work to sides of concrete foundations, footings, basis of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better with rough finished surfaces of concrete complete all as specified & directed.

Form work to sides of pillars, posts, struts piers, columns and stanchions and similar works fair finished surface of concrete complete all as specified & directed by Engr-in- charge.

Form work to sides and sofits of floor or roof beam, beam hanuchings, girders, bressummers, lintels, contilever, shelves including supports, overhangs etc also splay between floors and beam, complete all as specified & directed by Engineer-in- charge.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

All as specified in above herein before but 5 mm dia and over upto and including 10 mm dia in stirrups/spacers/binders complete all as specified and directed.

12 mm thick rendering in CM 1:4 on external surface plastering of fair faces of brick masonry or concrete surfaces & finishing the surface even and smooth without using extra cement complete all as specified.

15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement complete all as specified.

Preparation of new plaster surface of walls including cornices plaster etc, and applying two coats of cement base paint over a coat of approved primer, complete as specified and directed.

Hard core of broken stone/boulders of gauge exc 63mm deposited spread and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

Rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410W (Gde E-250), quality 'A' complete all as specified.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified.

AC plain sheet ceiling 4mm thick on aluminium grid work 60cmx60cm with using 36.5mmx23.5mmx1.5mm thick main tee, 23.50x23.50x1.28mm cross tee and 25x25x1.5mm angle fixed to perimeter of wall for false ceiling including necessary supporting hanger with 3.0m dia GI wire and J bolts washer nuts for securing frame work to ceiling suspended @120 cm C/C both ways, size of grid shall be 610x610mm, including two coats of oil bound distemper of over one coat of primer and preparation of surface complete.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 150mm long, complete all as specified.

75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base of floor finishing surface even, complete all as specified and as directed.

M & L light shaded Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed CM 1:6 over over and including 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base complete all as specified and directed..

Non skid coloured ceramic tiles 7 to 8mm thick square/rectangular area of each tile exc 0.11 Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including 15mm thick screed bed in CM (1:4), over and including 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in sub base complete all as specified and directed.

Glazed ceramic coloured tiles (300x200) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls/trenches as soil pipe(vent pipe), fixed, complete all as specified and directed.

PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing with solvent cement fixed, complete all as specified.

PVC (SWR) gully trap of 125/100mm, setting & jointing with solvent cement fixed, complete all as specified.

S & F waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms / 40mm-60gms) for 32mm bore dia of discharge pipe to WHB, sink, complete all as specified.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches or in floor/walls as soil pipe, fixed, complete all as specified and directed.

PVC (SWR) bends any radius 110mm bore, complete all as specified.

PVC (SWR) WC connector with lip ring 110mm, complete all as specified.

PVC (SWR) reducer 110/75mm fixed, complete all as specified.

PVC (SWR) vent cowl for 75mm dia fixed, all as specified.

Steel water tubing 15mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Lagging to pipes 15mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh, and covered with 0.01mm aluminium foil, complete all as specified.

Lagging to pipes 20mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh, and covered with 0.01mm aluminium foil, complete all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Factory Made Solid PVC Moulded Door Shutter with particle board, 28 to 30mm thick (styles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site all as specified and directed

Harrison rails (Curtain rails) mild steel, Chromium plated with fixing brackets, stops, rollers etc complete all as specified

PVC connection 15mm size with PTMT nuts on both ends of length 600mm, complete all as specified.

S & F Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and anti-syphonage pipe etc, complete all as specified.

S & F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, and fixed, complete all as specified and directed.

Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand and embeded in cement etc, complete all as specified.

15mm bore pillar tap fancy type cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule and fixed complete, all as specified & directed

PVC valve less syphonic action type flushing cistern 10 ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all connection fixed, complete all as specified and directed.

S & F in 15mm bore stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

S & F Vitreous china bowl urinal flat back size of 465X355X265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around the urinal back in cement, complete all as specified.

S&F Soap dish, vitreous china white approximate size 160x160x90mm, fixed to plug with chromium plated brass screw, complete all as specified.

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190gm), complete all as specified and directed.

Construction of brick masonry staging for over head water tank 2.4m height from ground level including necessary earth work in any type of soil complete all as shown on drawing No. CESZ/TD-1101/2011 Sheet 1/1 dt 01/12/2011, complete all as specified and directed.

150 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed as specified and all as directed by Engr-in-Charge.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm SGSW pipe after they are laid and tested in PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

Construction of soakage well, excavation, in any type of soil, foundation in PCC 1:3:6 type C1, as in footing, wall of honey combed/ solid mansonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonary in CM 1:4, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8 m dia x 3m effective depth, all as specified and shown in Drg No. CESZ/TD- 01/2015 sh 3/3 dated 22/2/15 & revised on 06/06/15.

Construction of 25 users septic tank (brick construction) including inlet and out let chamber with top of slab at ground level including necessary earth work and disposal of surplus soil to a distance not exceeding 50m supplying and placing vent pipe, in position to manhole cover brick construction and all other relevant works, complete, all as specified and shown on drawing No CESZ/TD-1/2015 Sheet 1/3 and 2/3 dt 22/02/2015, revised dt 21/03/2015.

S&F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe or brass ferrule fixed, complete all as specified.

Plain cement Concrete 1:2:4 type-B1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work and finishing the exposed surfaceof concrete all as per in relevent clause of SSR Part-I, complete all as specified and directed.

M&L one coat of primer with wall putty to obtain through true line and to achive the surface smooth and applying two coats of OBD incl preparation of new plastered surface complete all as specified.

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

Mild steel FI as in hold fasts and similar small articles fixed to chowkats, size 25mm x 3mm conforming to Fe-290 Gde E-165, complete all as specified and directed.

35mm thick 2nd class soft wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers supplyed and fitted with chowkats, complete all as specified and directed.

30mm thick 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (divided into square with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete, all as specified.

30mm thick 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (divided into square with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete, all as specified.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

150mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

Mild steel butt hinges, medium weight, cold rolled, 75mm long, complete all as specified.

Mild steel pressed handle, oval type stove enamelled, black of size 150mm, complete all as specified.

Mild steel pressed handle, oval type stove enamelled, black of size 100mm, complete all as specified.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 100mm long, complete all as specified.

Mild steel sliding door bolts, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate, 200mm long, all as specified.

Two coat of synthetic enamel paint over a coat of pink primer on new wooden or plywood surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete, all as specified.

M&L preparation of new steel and Iron surfaces over 10 CM width or girth not other wise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

Rotational moulded polyethylene water storage tank tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, connecting to inlet and outlet pipe connections, with and including 20mm dia GI wash out with plug, complete all as specified and directed.

M & L Chequered cement concrete tiles 200x200x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and with pigment to match shade of tiles, over and including 15mm thick screed bed in CM (1:6), over and including 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in steps and other similar bands, including use of form work complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe-410-W (Gde E-250) Quality-A complete all as specified

Plain Mild steel, plain, black sheet 1.25 mm thick in steel gates and straight flashing complete all as specified and directed.

Points wiring for one light point/fan point/socket controlled by one switch with 1.5 sqmm PVC FRLS insulted un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulted un-sheathed copper conductor single core multi stranded flexible cable as earth lead (using colour coding) in and including cable 1100 volts grade including casing and capping (ISI marked) for one light/fan point including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the distrubed surfaces to match with the existing specification complete all as specified.

Point wiring for 3 pin socket outlet 5 Amps on same board controlled by one switch with 1.5 sqmm FRLS insulted un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm FRLS insulted un-sheathed copper conductor single core multi stranded flexible cable as earth lead (using colour coding) in and including cable 1100 volts grade including casing and capping (ISI marked) including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the distrubed surfaces to match with the existing specification complete all as specified.

Point wiring for 3 pin socket outlet 15 Amps on the independent board controlled by one switch with 4.00 sqmm PVC FR insulted un-sheathed copper conductor single core multi strand flexible cable and 2.5 sqmm PVC FR insulted un-sheathed copper conductor single core cable (using colour coding) as earth lead in and including non metalic PVC capping casing meduim grade with all fittings (ISI marked) controlled by one switch including CI/MS sunk box of required size & as directed by Engineer in charge including 3mm thick plastic laminated top sheet cover,, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specfied.

S&F Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

S & F Switch Socket combination 2 in 1, 6 pin and 15 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

S & F Switch Socket combination 2 in 1, 5 pin and 5 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

Ceiling rose, surface backelite 65x50mm two or three terminals complete all as specified.

Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings including 9 watt LED bulb complete all as specified and directed.

S&F MCB's single pole and neutral, 240 volts 6 to 40 Amps all as specified and as directed by Engr -in-Charge.

S&F MCB's single pole 240 volts 6 to 32 Amps all as specified and as directed by Engr -in-Charge.

Sheet metal enclosures factory made, (Double door) for DBs, single pole and neutral, 240 volts, 8 ways with 200Amp rated busbar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, testing and commissioning, complete all as specified and directed.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 10Sqmm, complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI medium grade water pipe 20mm dia with funnel all as shown in electric plate No. 03 of 2009 SSR Pt-I and testing on complete including earth work in any type of soil, PCC 1:2:4 as in eartig pit CI pit cover 5.5mm thick common salt charcoal all as specified.

LED retrofit T8 type flourescent tube light fitting patti type 1x20 watts white powder coated CRCA sheet steel rust free housing complete electronic ballast, polycarbonate spring loaded bipin holder with bracket, connector block all accessories prewired with suitable size cable with decorative end caps including 1x20 watt LED tube rod and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core complete all as specified and directed. of cat pat No. LTDCO1220WLED /WD of make C&S or equivalent make of Bajaj/ Crompton/philips

Socket outlet 2 in 1, 3 pin, 5A, flush type universal, all as specified and as directed.

Supply and fix LED light fittings 1X9W bulk head luminaires etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 volt 50 HZ make Havells, Bajaj, Phillips complete all as specified.

Exhaust fan plastic 450mm sweep with louvers, 240 volt single phase including PVC flexible wire connecting to ceiling rose including making hole, groting nuts & bolts and plastering & making good the disturbed surface complete all as specified. Make : Havells model No. Turbo force SP or equivalent Make in Bajaj/CG/Khaitan

S&F Rectangular wooden boards/blocks 30x25x4cm depth closed recessed, complete all as specifed and directed.

House service bracket (hook type), complete, with 3m long GI pipe 40mm dia medium grade, two Nos 90 degree bend, MS hook and guy or stay, complete all as specified.

M/S FAYAZ CONSTRUCTIONS

M/S MOHAMMAD JAMAL WANI