24/EUDC(RB)/LESA/2024-25

Amount

Safe Dragging, loading, carriage and unloading of following store materials with proper stacking from ESC Daliganj to JE dump store and JE dump store to work site within municipal areas.

ABC 3X120+1X95+1X16 SQ MM

11 KV 3X185 SQMM XLPE CABLE

11 KV 3X185 SQMM XLPE CABLE S/T

11 KV 3X185 SQMM XLPE CABLE O/D

MS Earthing Rod (2540x20 MM)

Stay Set 16x1800 mm

Stay Wire (3.15 MM) 7/10 SWG

Distribution Box

STP 11 M long

11KV pin insulator

11KV Pin with Nut

GI wire 5 MM 6 SWG

M.S.channel 100x50 sq mm

M.S.Angle 65x65x6 sq mm

1x240 LT XLPE Cable

Digging of pit in Kachcha/Pakka land in depth upto 1/6 length of pole, Dragging of STP from nearby place/dump, Erection of single pole along with stone pad in bottom with proper alignment on 11 mtr long ST pole and refilling with ramming of earth

Grouting of pole in depth of 1/6 the length of pole in ratio 1:4:8 in cement, sand and brick ballast as per RESPO norms.

Construction of pole plinth 300 mm x 450 mm above ground level in 1:2:4 in cement, coarse sand and stone gritt as per RESPO norms.

Painting of new erected ST pole with two coat of Red oxide paint, PO red paint at top of pole 2 mtr and balance by two coats of best quality aluminium paint ISI of Berger/Nerolac/Asian paints as per norms.

Laying of 11 KV XLPE cable 3x185 sq mm S/C by digging of trench in pakka 800 mm deep & 500 mm wide its boxing with bricks & sand, laying of cable & separation of cables by brick wall, filling of sand up to top cover of the trench properly levelling & ramming & covering with stone slab after laying of cable. (All material shall be provided by contractor except 11 KV cable)

Fabrication & erection of 11 KV cable Exposure type double pole with the provission of bus bar with fixing of necessary clamps and other accessories like danger board, number plate, barbed wire, 6 no. pin insulators with pins, 2 No. MS-CHANNEL & 2no. MS angle for supporting the hoisting on Pole.Its jumpering by single core PVC aluminium cable with proper size of lug. Painting of double pole with one coat of red oxide & two coats of enamel paints (ISI mark). Its grouting in ratio 1:4:8 & plinthing 300 mm above ground level (All material to be arranged by contractor except steel,pole,PVC aluminium cable,earthing rod,Pin & Pin insulator).as per RESPO norms. .

Fabrication of 11 KV cable Exposure type double pole with the provission of bus bar with fixing of necessary clamps and other accessories like danger board, number plate, barbed wire, 6 no. pin insulators with pins, MS-CHANNEL & angle on old & existing rail pole with painting of poles and channels

Hoisting of 11KV, 3x185 sq mm XLPE on D/P with G.I. pipe 4" dia , clamp nut and bolt and other required material (All materials shall be provided by contractor except 11 KV cable)

Digging of pit of size 3x2x1 mtr. for making straight through joint 11 KV work involved filling of soil levelling and ramming of the same.

Making Heat & shrinkables joints of following sizes and types 11 KV 3x185 sqmm XLPE cable by Heat and shrinkables jointing kits. (Jointing kit will be provided by deptt. )

Straight through for 11 KV 3x185 sqmm

Outdoor/Indoor end termination kit for 11 KV 3x185 sqmm XLPE cable

High Pressure Testing

Construction of plinth suitable for LT mini piller box.

Supply, erection and commissioning of LT mini piller box/ B pannel as per approved drawing

Disconnection of old L.T. Cable from old L.T. piller box and reconnection from new LT mini piller box/ B pannel with fixing of required lugs.

Erection of single pole suport on 11 M long STP with fixing of necessary clamp, J hook, suspension clamp & piercing connector etc which are required for ABC L.T. line. (All material shall be provided by contractor except 11 ST pole)

Erection of Stay set 16x18 mm

Stringing and sagging of L.T. ABC 3x120+1x95+1x16 SQ MM

Erection and commissioning of L.T. distribution box 3 phase with required clamp. (All material shall be provided by contractor except L.T. Distribution box)

Disconnection of service cable of consumers from old L.T. line/ pole/D.box and reconnection from new erected D. box. After laying of L.T. line.

Dismantling of old pole and remove old conductor

Dismantling of old L.T. Pannel

Carraige of recived back materials (Poles, conductor and other scraps materials ) from site to LESA store.

All taxess as applicable shall be paid time to timre extra

M/S RATHORE ELECTRICALS (BID ID -4691428)