Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹25.6 LAccepted-AOC HOUSE NO 11 VILLAGE POST SAIGAON THE BHALKI DIST BIDAR STATE KARNATAKA 585416 | BIDAR | KARNATAKA | 585416 | ₹25.6 L Quoted ₹27.1 L | L1 | Accepted-AOC Quoted rates are reasonable |
| 2 | L2₹28.9 LRejected-Finance GARDEN AVENUE PLOT NO 242 243 244 RH 4 SECTOR 21 NERUL NAVI MUMBAI 400 706 | THANE | MAHARASHTRA | 400706 | ₹28.9 L | L2 | Rejected-Finance Greater than L1 |
| Sl No | Description | Qty | Unit | M/s S.D Construction Co L2 | JADHAV CONSTRUCTION AND INFRASTRUCTURE L1 |
|---|---|---|---|---|---|
| 1.00 | Recieving and Attending day to day complaints lodged by the user/occupants from JE incharge and carrying out Petty/Minor repairs related to joinery and builders hardwares such as easing/adjusting of shutters of any type of size, re-fixing of wire mesh, cupboard shutters/shelves/kitchen shelves, easing/adjusting/re-fixing of hinges, tower bolts, handles, stoppers, sliding door bolts/locks, magic eye,hook and eyes, hasp and staples, easing of doors and windows of Aluminium, tighting of wire mesh, repairs to holes in roof sheets with fixing of washer and plug/M Seal etc including taking down of existing material as ordered/required on all working day to attend the complaint cell by rep of contractor at 0900 AM and report to complaint cell at every evening at 0500 PM on daily basis after satisfactory completion,complete all as specified and directed by Engineer-in-Charge. Material such as nails,screws, washers, putty/beading for glass / wiremesh, nut & bolts etc as per site requirement shall be included in the the quoted rate. Minimum 01 carpentar & 01 helper is required with Cycle. Note:-(i) The complaint against docket shall be taken from MES Complaint cell/JE Incharge at every morning at 0900 AM by rep of contractor on daily basis. (ii) Necessary T&P, equipment and safety gear shall be provided by the contractors.
(iii) Easing/adjusting of shutters and builders hardwares, tightening the handle/knob/nuts/screws, oiling/greasing etc will be treated as minor/petty repairs.
(iv) Rs. 100.00/complaint per day shall be recovered as penalty against non attending of every complaints after 03 days from reciept of complaints. Note: Replacement of Major items shall be measured and paid separately under relevent item & this item shall not be measured in that case. | 1,400 | Each Job | 232 ₹3.2 L | 150 ₹2.1 L |
| 2.00 | S&F in repairs 25 mm dia curtain rod, mild steel, Powder coated decorative type complete all as specified. | 100 | RM | 150 ₹15,000 | 250 ₹25,000 |
| 3.00 | S&F in repairs 25mm dia decorative type brackets, mild steel, powder coated complete all as specified. | 150 | Each Pair | 90 ₹13,500 | 150 ₹22,500 |
| 4.00 | S &F, in repairs, Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge. | 80 | Sqm | 700 ₹56,000 | 250 ₹20,000 |
| 5.00 | S&F in repairs 4 mm thick sheet glass ordinary quality, in square or reqd shape n exc 0.50 Sqm each complete all as specified. | 10 | Sqm | 700 ₹7,000 | 1,500 ₹15,000 |
| 6.00 | S&F in repairs 4 mm thick figured glass pin headed type in square or reqd shape n exc 0.50 Sqm each complete all as specified. | 5 | Sqm | 750 ₹3,750 | 1,400 ₹7,000 |
| 7.00 | S&F in repairs 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified. | 20 | Each | 110 ₹2,200 | 150 ₹3,000 |
| 8.00 | S&F in repair 100mm stain less steel SS-304 heavy grade designer butt hinges medium weight complete all as specified and directed by Engineer-in-Charge | 70 | Each | 70 ₹4,900 | 150 ₹10,500 |
| 9.00 | S&F in repair 150 mm stain less steel SS-304 heavy grade designer handles extruded section fabricated type in any position complete all as specified and directed by Engineer-in-Charge. | 40 | Each | 160 ₹6,400 | 250 ₹10,000 |
| 10.00 | S&F in repair 150 mm stain less steel SS-304 heavy grade designer tower bolts extruded section fabricated type in any position complete all as specified and directed by Engineer-in-Charge. | 70 | Each | 175 ₹12,250 | 250 ₹17,500 |
Updated dates
Tender Value
₹30 L
EMD Value
₹60,000
Closing Date
15 Nov 2025, 6:00 pmClosed
Gaurav Tiwari, IDSE
GE (I) (NAVY), INS SHIVAJI - POST, LONAVLA -410402
DAY TO DAY MAINT SERVICES AT AGE BR II AT INS SHIVAJI LONAVLA
2025_MES_734739_1
GE/LONAVLA/8371/E8
Open Tender
Civil Works
225 days
GE (I) (NAVY) LONAVLA
Please refer Tender documents.
6 documents required · 6 mandatory
₹500
Yes
GE (I) (NAVY) LONAVLA
₹60,000
Yes
16 Jan 2026
11 Oct 2025
17 Nov 2025
11 Oct 2025
15 Nov 2025
27 Oct 2025
11 Oct 2025 - 25 Oct 2025
Amount
S&F in repairs 25 mm dia curtain rod, mild steel, Powder coated decorative type complete all as specified.
S&F in repairs 25mm dia decorative type brackets, mild steel, powder coated complete all as specified.
S &F, in repairs, Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge.
S&F in repairs 4 mm thick sheet glass ordinary quality, in square or reqd shape n exc 0.50 Sqm each complete all as specified.
S&F in repairs 4 mm thick figured glass pin headed type in square or reqd shape n exc 0.50 Sqm each complete all as specified.
S&F in repairs 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified.
S&F in repair 100mm stain less steel SS-304 heavy grade designer butt hinges medium weight complete all as specified and directed by Engineer-in-Charge
S&F in repair 150 mm stain less steel SS-304 heavy grade designer handles extruded section fabricated type in any position complete all as specified and directed by Engineer-in-Charge.
S&F in repair 150 mm stain less steel SS-304 heavy grade designer tower bolts extruded section fabricated type in any position complete all as specified and directed by Engineer-in-Charge.
S&F in repair 100 mm stain less steel SS-304 heavy grade designer tower bolts extruded section fabricated type in any position complete all as specified and directed by Engineer-in-Charge.
S&F in repair 300mm long stain less steel SS-304 heavy grade designer sliding door bolt with hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed with door complete all as specified
Taking down Chowkhats or frames not exc. 1.5 sq.m each with shutters ( without taking off shutters from the frames) and making good disturbed surfaces including removing disposable materials from worksite outside MD land at any distance complete all as specified.
Taking down chowkhats or frames exc. 1.5 sq.m and n exc 4 sq.m. each with shutters ( without taking off shutters from the frames) and making good disturbed surfaces including removing disposable materials from worksite outside MD land at any distance complete all as specified.
Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each making good disturbed surfaces including removing disposable materials from worksite outside MD land at any distance complete all as specified.
Taking down shutters of any description n exc 1 sq.m each making good disturbed surfaces including removing disposable materials from worksite outside MD land at any distance complete all as specified.
S&F aluminium ventilator louvered type without sash bar section as per designation 63400 of IS 737 approved by GE( minium 50 micron anodised) including necessary jointing clip, rubber packing,including necessary locking arrangement , anodised snap beading screws and 4mm thick pin headed glass etc complete all as specifed.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other coloured Frames/ Chowkhat of size 50 x 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum oxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal trength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and as directed by Engineer-in-Charge by engineer -in - charge.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other coloured Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum oxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal trength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and as directed by Engineer-in-Charge by engineer -in - charge.
S&F Factory made 30 mm thick single extruded WPC (Wood Polymer Composite) both side laminated of solid shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)
S&F Providing 30mm thick factory made wire mesh solid WPC door shutter both side decorative /laminated structure consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mmx25mmx2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19x6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.
S&F Solid WPC frame (Single Rebated) of size 50mm x 70mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified
S&F Factory Made 24 mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Flush door Shutter of required size and colour (one side decorative other side plain ) comprising of virgin PVC and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) having good screw holding capacity Minimum Compissive of 50 N/mm2, of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant complete all as specified.
S&F in stainless steel sliding door bolt of 300mm long medium weight complete all as specified and directed by Engineer-in-Charge
S&F stainless steel butt hinges, 100mm, medium weight complete all as specified and directed by Engineer-in-Charge
S&F extruded stainless steel handles, fabricated type of size 150mm in any position complete all as specified and directed by Engineer-in-Charge.
S&F in stainless steel, barrel tower bolts of extruded section of size 200mm complete all as specified and directed by Engineer-in-Charge.
S&F for Renewing glazed wall tiles in patches , area n exc 5 Sqm including cutting out broken tiles, removing and cleaning loose tiles, preparing bed, removing rubbish and replacing old with new tiles to match, complete with all cuttings, etc, and laying or setting, jointing and pointing or new or old tiles including 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge.
S&F for Renewing floor tiles in patches , area n exc 5 Sqm including cutting out broken tiles, removing and cleaning loose tiles, preparing bed, removing rubbish and replacing old with new tiles to match, complete with all cuttings, etc, and laying or setting, jointing and pointing or new or old tiles including 15mm thick screed bedding layer in CM 1:4 complete all as specified and directed by Engineer-in-Charge.
Dismantling of floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed by Engineer-in-Charge.
M&L glazed ceramic coloured tiles (300mmx 450mmx7 mm) in vertical surfaces jointed in neat cement slurry and pointed in white cement. Incl cutting the tiles to the required size whereven required incl mitring the corners etc over 10 mm thick backing coats of cement plaster in CM (1:4) complete all as specified and directed by Engineer-in-Charge.
M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (desined pattren) (square/ rectangular) area of each tile exceeding 0.06Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick in CM (1:6) for laying floor tiles complete all as specified and as directed by Engineer-in-Charge.
Demolition of concrete in ground floors (un re-inforced) and paving n.exc. 15 cm thickness (below or above ground level) and removal of rubbish/ demolished materials out of MD land complete all as specified and directed by Engineer-in-Charge.
Material and labour for providing 75mm thick plain cement concrete (1:3:6) type C-2 , using 20mm graded stone aggregate , laid in 1:20 slope in alternate bays as in plinth protection, surface finished even and smooth without using extra cement, complete all as specified.
M&L for 25mm thick plain cement concrete 1:2:4 mix,type B1 (using 20 mm graded stone aggregates) as in subbase to floor complete all as specified and as directed by Engineer-in-Charge.
M&L for vertified ceramic tiles 9-10 mm thick joint free double charged (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM 1:6 laying floor finished complete all as specified and directed by Engineer-in-Charge.
All as per above item no 37 but as in skirting over and including 10 mm thick backing coat with cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge .
Taking down cement or cement lime plaster, any description on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water etc.
Material and labour for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surface of walls, finished fair and even without using extra cement complete all as specified .
M&L for new plastered surface of wall, applying two coat of oil emulsion distember with preparation of alkali resistance primer paint over two coats of white cement based wall care putty smooth finish etc of approved make & shade complete all as specified and as directed by Engineer-in-Charge.
Material and labour for rendering 15mm thick on other than fair faces of brick work or concrete wall surfaces in cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified.
Material and labour for newly plastered surface of walls and applying two coats of exterior grade weather resistant, antifungal paint over one coat of acrylic primer on walls, chajjas,etc complete all as specified and as directed by Engineer-in-Charge.
Demolition of brick work/stone masonary built in cement mortar incl coping etc complete all as specified including removing of materials obtained from demolition from worksite to outside MD land at any distance complete all as specified and directed by Engineer-in-Charge by Engr-in-charge.
M&L for Brickwork with sub class 'B' bricks old size, straight or curved on plan exc 6m mean radius built in CM 1:6,complete complete all as specified and directed by Engineer-in-Charge
Supply only Integral Water Proofing Compound
Taking down 15mm dia bore GI steel tubing and connection including cleaning or removal from site complete all as specified.
Cutting to brick walls chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing , etc., and making good, cutting not exc 10 cm girth complete all as specified.
S&F CPVC pipes, SDR 11, 16 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all brass fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure
Taking down 20mm dia bore GI steel tubing and connection including cleaning and making good dismantaled surface complete all as specified.
S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all brass fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure complete all as specified.
Taking up or down steel/GI/CPVC tubing 25/32 mm and connection, including cleaning for refixing or removal to store complete all as specified.
S&F CPVC pipes, SDR 11, 25 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure complete all as specified.
S&F in repairs Bib taps, fancy type, chromium plated Quarter turn with crutch sc-rewed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified and as directed by Engineer-in-Charge.
S&F in repair Pillar taps, fancy type, chromium plated, Quarter turns crewed down, high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore complete all as specified and as directed by Engineer-in-Charge.
S&F in repairs Stop valves/Cock/Angle Cock 15 mm dia, fancy type chromium plated, screwed down, high pressure, screwed both ends for 15mm dia pipe or for unions fixed compete all as specified
S&F in repair Vitreous china white flat back of size 550x400mm wash basins, vitreous china (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe including 32 mm dia CP waste fitting complete all as specified and directed by Engineer-in-Charge.
S&F in repair stainles steel sink with drainage board , 1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers and wastes including bedding in cement morter to dwarf wall or including fixing CI cantilever bracket, connecting union to pipe etc., overall size 915 x 460 mm with bowl size 410 mm x 330 mm x 160 mm etc complete all as specified and directed by Engineer-in-Charge.
S&F in repairs stain less steel Wall Mounted Kitchen Utensils Dish Rack Stand With Plate & Cutlery Stand of Size (10 x31x48 Inches) Dish Stand/Holder the sample approved and as directed by Engineer-in-Charge by Engineer- in -charge.
S&F in repair Chromium plated shower rose with or with out swivel joints ,any size ,including fixing to steel pipe or union etc complete all as specified.
S&F in repairs 20mm Gun-metal, globe or gate valves, with iron wheel headcomplete all as specified
S&F in repairs 25mm Gun-metal, globe or gate valves, with iron wheel headcomplete all as specified
S&F in repairs 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball. (Minimum weight 20mm-210gms)complete all as specified
S&F in repairs 25mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified
S&F in repair Vitreous china wash down water closet (Padestal pattern) pan white including bolts and flush pipe, pedestal pan and trap including connections to drain (or outgoing pipe) and flushing pipe etc including seat cover closed type complete all as specified.
S&F in repairs vitreous china water closet 'Orissa' pattern of size 580mm X 440mm, white with integral foot rest (excluding flushing cistern), but including PVC flush pipe and provision of lime concrete bedding complete all as specified and as directed by Engineer-in-Charge.
S&F in repair 10 litre PVC valveless, duel function syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified.
S&F in repairs for CP Health faucet of brass body with wall hook and 1mtr stainless steel braided rubber hose pipe fixed in repair complete all as specified and as directed by Engineer-in-Charge.
S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm longcomplete all as specified.
S&F in repairs Brass chromium plated tubelar towel rail, 20mm dia, D type, 60,cm long between flanges all as specified.
S&F in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nutscomplete all as specified.
S&F in repairs 40mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts complete all as specified.
S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mmcomplete all as specified
S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mmcomplete all as specified
S&F in repairs water tank cover for tanks of size 500 ltr to 2000 ltrs capacity water storage tankcomplete all as specified.
S&F in repairs 32mm dia PVC waste pipe (LDEP) for wash basin and kitchen sink / Urinals complete all as specified.
S&F in repairs 40mm dia PVC waste pipe (LDEP) for wash basin and kitchen sink / Urinals complete all as specified.
S&F in repairs' flushing cistern kit' for complete set to fitted inside as per requirement for cistern functional completecomplete all as specified.
S&F in repairs 16mm CPVC pipes fittings such as elbow, socket, Nipple, Tee & reducer etc complete all as specified.
S&F in repairs 20mm CPVC pipes fittings such as elboe, socket, Nipple, Tee & reducer etc complete all as specified.
S&F in repairs 25mm CPVC pipes fittings such as elboe, socket, Nipple, Tee & reducer etc complete all as specified.
Vegitation clearance (plants ,shrbs,bushes are grow upwards vertical surface of walls ,duct area ,etc of any height and in any position including all necessary saftey precaustions of ladder,scaffolding etc complete all as specified and as diriected by Engineer -in -charge .
Dismantling of cast iron/PVC or reinforced concrete drain pipes, jointed in cement mortor and taking out of trenches/walls with all acessories if required 100/75 mm internal dia pipe complete all as specified.
S&F 75mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type B in any lenth with rubber ring joints fixed to walls,floors complete all as specified.
S&F 110mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type B in any lenth with rubber ring joints fixed to walls,floors complete all as specified.
S&F in repairs PVC (SWR) bends 75mm bore with access door complete all as specified.
S&F in repairs PVC (SWR) bends 110mm bore with access door complete all as specified.
S&F in repairs PVC (SWR) branch piece 110mm, single (single Y) equal or unequal complete all as specified
S&F in repairs PVC (SWR) junction single 110mm, (Single T) equal or unequal complete all as specified
S&F in repair PVC floor/ Nahani trap 110mm size with SS grating including removing existing traps and jointing to waste pipe fixed in cement concrete type type B1 (1:2:4) all as directed by Engineer-in-Charge
Dismentling wall and celing boards (fibre,pulp, insulation ,etc) or insulation boards/blankets,any thick ness including cover fillets all as specified.
S&F of 4mm thick 'E' classic designer board false ceiling with powder coated GI snap grid frame work of grid size 600 x 600 mm including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B 0 Cement motar 1:3 complete all as specified and directed by Engineer-in-Charge including all necessary drilling and necessary arrangement to fix items as under :- (a) 27x27x0.55 mm thick GI angle powder coated duly plugged @ 600mm centre to centre alongwith perimeter of wall. (b) 25x25x0.55 mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders (n.exe 1.2 mtr length) with adjustable clamps and dash true fastners plugging in RCC slab/wooden truss/A.I Runner of slopped roof placed @ 600mm centre to centre from perimeter of wall. (c) Fixing of 4mm thick AC "E" Classic designer board of approved texture and finished complete. Note. The complete ceiling work shall be done as per manufactures instruction and as directed by Engineer-in-Charge.
Cutting holes into brick/stone walls of size nexc 150sq.cm (superficial area) and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed by Engineer-in-Charge.
Dismantling plain or corrugated steel sheeting, any gauge, and thickness including Nainital pattern and roof covering, complete all as specified.
S&F for Pre- Painted galvalume aluminium zinc coating GI based corrugated/plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, including taking down complete all as specified and directed by Engineer-in-Charge.
Cutting chases,for concealed/fixing galvalume sheet etc., and making good, cutting not exc 10 cm girth pinning in. making good to facing of stone concrete block or slab walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, chajjas etc.; complete all as specified.
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.
S&F roof trusses (framed), sunshade frames, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-410-W(Gde-E-250) including taking down all as specified and directed by Engineer-in-Charge
S&F framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified.
S&F Steel work in tubular section as purlin,rafter ,etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 including distance pieces, cleats etc complete all as specified and as directed by Engineer-in-Charge.
M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of anticorrosive paint(Epoxy) over a coat of epoxy primer complete all as specified and directed by Engineer-in-Charge.
Excavating post holes or similar holes, each not exceeding 0.50 Cu. M, getting out in Hard/ Dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 100m & making good surface complete all as specified and directed by Engineer-in-Charge.
M&L Plain Cement Concrete Type B1 1:2:4(using 20 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.
M/s S.D Construction Co (BID ID -3466191)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.72 MB
8371tenderdocufinal.pdf
Tender Documents • 1.43 MB
BOQ_822724.xls
BOQ • 2.03 MB
Download all tender documents and submit your bid