SPECIAL REPAIRS TO OFFICERS LIVING IN ACCOMMODATION T296 T297 AND T298 AND PROVN OF SOAKAGE WELLS INCLUDING CONNECTING LINES AT OFFICERS MESS AT AIR FORCE STATION JAISALMER

Amount

Taking down door/window chowkhats not exc 1.50 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down door chowkhats or frames with shutter (without taking off shutter from the frame) exc 1.50 but not exc. 4 sqm in each complete all as specified and directed.

Taking down door shutters of any description of area exc 1.00 sqm but not exc. 2.00 sqm in each complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or any thickness, pointed in any mortor or any height in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections and fittings, including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections and fittings, including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 25mm dia steel tubing and connections and fittings, including cleaning for refixing or removal from site complete all as specified and directed.

Taking down cement plaster of any description, on brick or stone or PCC block masonry walls/ceiling etc. including raking out joints, hacking for key, scrubbing down with water etc and including removing debris/rubbish from the premises upto 500m from site complete all as specified and directed.

Demolition of cement concrete (unreinforced) in any position/height not exceeding 15cm thickness (below or above ground level) and including removing debris/rubbish from the premises upto 500m outside the MoD land complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar complete all as specified and as directed.

M&L for cement concrete (1:2:4) tpe B-0 using12.5 mm graded stone aggregates as in bands, bed blocks, fixing hold fasts, filling of door frames etc complete incl necessary formwork complete all as specified and as directed.

M&L for 75mm thick plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection including joints 10mm wide and full depth at 3m distance and every change of direction filled with mixture of bitumin and sand for plaster in (1:3) complete all as specified and directed.

M&L for 25mm thick cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors finished the surface even and rough complete all as specified and directed.

M&L for precast cement concrete solid block ( 1:3:6 ) type C-1 (using 20mm graded stone aggregate) exc 10cm in width as in block masonry built in cement mortar (1:6) etc complete all as specified and directed.

M&L for 10mm thick rendering cement plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces and stone masonry surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering cement plaster in cement mortar (1:4) on fair faces of brick work or concrete surfaces surface finished even and smooth without using extra cement with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only.

M&L for rendering 5mm thick rendering cement plaster in cement mortar (1:3) on uneven faces of concrete surfaces in ceilings and finished even and smooth without using extra cement complete all as specified and directed.

M&L for complete removal of old existing treatment, filling up undulation and applying 1.0mm thick readymixed wall putty on entire surface of wall etc cutting and finishing with appropriate sand paper and applying two coats of oil bound distemper (White or tinted) over one coat of priming paints plaster coat after smoothening of surfaces of wall complete all as specified and directed.

M&L for preparation of old treated surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and distempering with two coats of oil bound distempering on over a coat of priming paints plaster coat complete all as specified and directed.

M&L for preparing of new plastered sufarce of ceiling and applying three coats of white wash all as specified and directed.

M&L for preparation of old painted wooden surface or wood based materials of any description, not otherwise described, over 10cms widths or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing new wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparing old decorative or unplastered surfaces of walls by brooming down,scraping down smoke soot,mould ,moss and effloresence salts and greasy spots and applying one coat of exterior emulsion paint (APEX of Asian paints or equivalent in NEROLAC,JENSON& BERGER PAINTS ) of any colour as approved by GE complete all as specified and directed.

M&L for preparing New Plastered surfaces of walls and applying two coat of exterior emulsion paint (APEX of Asian paints or equivalent in NEROLAC,JENSON& BERGER PAINTS ) over a coat of Primer of any colour as approved by GE complete all as specified and directed.

M&L for Double Charged Virified Ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

M&L for Vitrified coloured ceramic tiles 10mm thick as in skirtings, dados and verticle surfaces polished, area of each tiles not exceeding 0.36 sqm over and including 10mm thick rendering cement plaster in cement mortar(1:3) set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm in floors etc over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

M&L for (300mm x450mm) x 6 to 7 mm thick coloured glazed ceramic tiles as in skirtings, dados and verticle surfaces etc over and including 15 mm thick screed bed or bedding layer in cement mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed. d.

S&F framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, doors or gates, ladders, framed balusters, walk ways, railings, frame work of watertanks etc ant type of work of steel grade Fe 410 -W (Gde- E- 250) quality-A complete all as specified and directed.

S&F 2nd class hard wood plain, framed , paneled shutters 35mm thick (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (part-I) , kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick factory made Second Class Hard wood glazed/skeleton shutters open rebated prepared to receive glass, gauze etc devided in squares with plain, chamfered or rounded, mitred and rebated sash bars any number with plain, chamfered or rounded, mitred and rebated beads for securing glass gauze etc. complete all as specified and as directed.

S&F factory made solid PVC door frame of size 50x47mm made out of 5mm thick rigid PVC foam sheet reinforced with MS square tube complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement and fixing in the frame at side complete all as specified and as directed.

S&F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame/shutter work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including roller for sliding window, handle, locking device, necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and complete all as specified and as directed.

S&F expanded metal mesh Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and complete all as specified and as directed.

S&F Stainless steel (Grade SS-304) wire cloth 0.36mm nominal dia of wire and average width of aperture1.40mm and fixed with stainless steel wire staple fixed with aluminium beading etc complete all as specified and as directed.

S&F 5.0mm thick Figured glass and fixed to aluminium Ventilation in square exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 100mm long Butt hinges, extruded aluminium alloy with galvanished mild steel hinge pin anodised and fixed type B-21 complete all as specified and as directed.

S&F 100 mm long mild steel butt hinges medium weight cold rolled complete all as specified and as directed.

S&F 200mm size aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F 300mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) & fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 300mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F 150mm size aluminum anodized handle cast type complete all as specified and as directed.

S&F in repair 25 mm dia stainless steel curtain rod (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed.

S&F 15mm bore galvanised steel tubing (ISI) marked medium grade with necessary fittings like tees, elbows, sockets, reducers, bends etc including necessary cutting, threading laid in trenches/floors, fixed to walls(concealed) etc complete all as specified and directed.

S&F 20mm bore galvanised steel tubing (ISI) marked medium grade with necessary fittings like tees, elbows, sockets, reducers, bends etc including necessary cutting, threading laid in trenches/floors, fixed to walls(concealed) etc complete all as specified and directed.

S&F 25mm bore galvanised steel tubing (ISI) marked medium grade with necessary fittings like tees, elbows, sockets, reducers, bends etc including necessary cutting, threading laid in trenches/floors, fixed to walls(concealed) etc complete all as specified and directed.

M&L for Cutting chases in brick/stone/concrete walls, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. (Note:- This item shall be applicable in old brick/stone/concret masonry)

S&F in repair 20mm dia Gun Metal, globe or Gate Valve with iron wheel head Screwed both ends for Iron Pipe and fixed complete all as specified and directed.

S&F in repairs 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), Tripple layered, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, etc including disconnecting and removal of existing water tanks from site complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern) with any type of 'P' or 'S' trap excluding flushing cistern and flush pipe, including fixing of water closet complete with plastic water closet seat black/white closed pattern witrh flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repairs Vitreous China wash basin, wliile, flat back, size 580x450mm excluding taps, waste, chain and plug and porcelain stopper but fixing on counter top slab including waste fitting, brass chromium plated 32 mm size with long screwed shucks and fly nuts and including PVC discharge pipe complete all as specified and as directed.

S&F in repairs10 litres capacity low level flushing cistern , valveless, syphonic action type with inlet, ball valve, float and handle, body moulded from virgin quality high impact poly propoliyone including brackets and 32 mm dia PVC flush pipe for low level flush cistern complete all as specified and directed.

S&F in repair 15mm bore fancy type chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair15 mm bore angle cock fancy type chromium plated, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F as in Repair wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting 'Continental Range, Model No : CON 273 KNUPR) or equivalent complete all as specified and as directed.

S&F in repair hand shower (health faucet) (ABs body) with 8mm dia one meter long flexible tube in chrome finish incl wall hook & wall work incl fixing compl (Make : JAQUAR, Model No ALD-579)or equivalent complete all as specified and as directed.

S&F in repair Toilet paper holder with flat recessed type stainless steel (Make : JAQUAR, Model No ACN-1153S)or equivalent complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with fixing chromium plated bracket, guard and railing 55/56cm long complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D Type, 60cm long between flanges complete all as specified and directed.

S&F in repair 15mm bore Brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed (Make-JAQUAR, Model No CON-167 KNB) or equivalent complete all as specified and directed.

S&F in repairs 75mm dia Chromium plated shower rose with Chromium plated arms with swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 15mm size PVC connections with PTMT nuts of length 600mm suitable for 15mm dia pipe complete all as specified and as directed.

S&F in repair 75mm outlet dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/floor or fixed to walls including digging and making good as existing complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) Junction single (Single T) equal or unequal with access door complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to walls including digging and making good as existing complete all as specified and as directed.

S&F in repair 75mm bore PVC (SWR) bend any radius complete all as specified and as directed.

S&F in repair Stack clamps out of 50mm x 5mm flat iron and 16 mm dia round iron stays.including bolts and nuts and securing ends of stays to wall or roof in dia 110mm pipe complete all as specified and as directed.

M&L for repairing of RCC projection,chajjas,roofs,facia,column etc by necessary preparation i.e scarping, cutting, chiseling,derusting and cleaning exposed reinforcement, surface of damaged,loose RCC surface and applying one coat of rust remover by brushing to rusted reinforcement to remove loose rust particles and allow to dry it for 2 to 3 hours,insert the new reinforcement to damaged portion by drilling hole at required distance,fill the epoxy in to the hole by 2/3 of the hole and insert the reinforcement in the hole, and binding the reinforcement at rusted portion of reinforcement,apply cement slury on entire damaged area,and plaster the surfaces with cement,sand and polymer liquid in 1:3:15% of cement by weight ) and water as required ,mixing properly and plaster the surface ,finished even and smooth by making the edge water dropping groves complete all as specified and directed. Note: cost of formwork shall be deemed to be included in the quoted rates.

M&L for providing Factory Made 18mm thick 100% Solid WPC decorative ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm as per ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete all as specified and diected. (For WC/Bathroom/Toilet/Kitchen/Balcony Doors and Cabinets)

Excavating in trenchesin any type of soil n exc 1.5m wide and n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out complete all as specified and directed.

Returning, refilling in including spreading levelling watering &well ramming in layers n.exc 25cm in hard/dence soil complete all as specified and directed.

Removing of excavated material n.exc 50 m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed.

Demolation and breaking up drain pipes of 150 mm dia (Salt glazed ware ,AC or Reinforced concrete ) set in cement mortar including bedding haunching complete all as specified and directed by Engineer-in-Charge

M&L for 150 mm bore reinforced cement concrete pipe, class NP3, with collars; laid on concrete bed to required slope and jointed complete all as specified and directed.

M & L for cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in concrete bed for 150 mm bore reinforced cement concrete pipes including packing under haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M&L for 10mm thick rendering cement plater in cement mortar (1:3 ) on concrete surfaces or masonry surfaces as in manholes,gully traps etc and finished even and smooth without using extra cement complete all as specified and directed.

Demolition of cement concrete (unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping, benching of manholes etc, and including necessary formwork and including demolition of existing PCC complete all as specified and directed.

S&F inreplacement SFRC manhole covers with rectangular frame of size 44"x26" MD-10 fixed at site up to satisfactoin of GE including dismentling of old manhole cover slab complete all as specified and directed.

S&F in repair 180mmx150mm size Salt-glazed stoneware gully traps, square or round mouthed, type 'P' complete all as specified and directed.

Supply only integral water proofing compound, make as approved by GE complete all as specified and directed.

Construction of Septic tank for 50 users capacity complete all as shown on Drawing no. CEAA/TD/116 Sheet No. 1/6 to 6/6, excavation and earth work in any type of soil and strata, moorum filling, lean concrete PCC (1:5:10) type E-2 using 40mm graded crushed stone aggregate below foundation, RCC M-25 design Mix in 100mm thick Slab, 100mm thick Baffle wall and 60mm thick Manhole Cover and 500mm thick precast cement concrete (1:2:4) type B-1solid building blocks masonry wall built in cement mortar (1:4), 15mm thick internal and external plaster in cement mortar (1:4) upto15cm below ground level mixed with water proofing compound, 110mm bore PVC(SWR) inlet pipe from manhole and PVC(SWR) outlet pipes with "T" junction and 75mm bore PVC(SWR) vent shaft pipe with slotted cowl of 2m height; 50mm thick PCC(1:2:4) type B-1 using 20mm graded crushed stone aggregate as in flooring surface finished even and smooth using extra cement mixed with water proofing compound , RCC manhole cover, MS Rungs, reinforcement and formwork etc complete complete all as shown on drawing, specified and as directed by GE.

Construction of Soakage Well 3m internal diameter and 3m effective depth complete all as shown on Drawing No. CEAA/TD/80 Sheet No. 1/2 to 2/2, excavation and earth work in any type of soil and strata, Brick work using sub class “B” bricks masonry wall built in cement mortar (1:6) straight or curved on plan exceeding 6m mean radius, Brick work using sub class “B” bricks in one brick thick honey comb masonry wall built in cement mortar (1:4)loose filling with broken stone or boulders of gauge exceeding 80mm but not exceeding 150mm, RCC M-25 Design Mix as in 150mm thick Slab, Plain cement concrete (1:2:4) type B-1 as in bands, Precast cement concrete (1:2:4) type B-1solid building blocks masonry wall built in cement mortar (1:4) in lieu of coarse coarse sand filling, 15mm thick internal and external plaster in cement mortar (1:4) upto15cm below ground level mixed with water proofing compound, 110mm bore PVC(SWR) inlet pipe from septic tank, cast iron manhole cover etc complete complete all as shown on drawing, as specified and as directed by GE.

Taking down carefully aluminium point wiring on wooden battens/through conduit (light fan, socket or power) complete with fittings such as switches, wooden batten, ceiling roses, pendants, regulators, box type tube light fittings, removing the materials from site except fittings etc which shall be reused in the work and making good the disturbed surfaces of walls/ceiling/ floors etc complete all as specified and as directed.

Taking down carefully unserviceable MCCB's/MCB's of any type any capacity complete all as specified and as directed.

Taking down carefully unserviceable distribution board any type any capacity complete all as specified and as directed.

Taking down carefully unserviceable light fittings any type any rating complete all as specified and as directed.

Takling down of geysers and deposited to MES store complete and Hanging/re-fixing only of geysers after collection from MES Store yard including necessary fasteners complete all as specified and directed.

Taking down carefully unserviceable submain wiring any type any rating complete all as specified and as directed.

M&L for point wiring for controlled by one switch with PVC insulated but unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 1.5 Sqmm (nominal area) in and including non metallic rigid PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling with including one run of PVC insulated FRLS copper conductor cable of 1.5 Sqmm with green insulation as earth wire and connected to earth dolly including sunken box of size 1.6mm thick and 60 mm depth presse ssteel box factory made for mounting of switch, socket and fan regulator with modular frame covers, complete all as specified and directed.

One light point controlled by one, one way switch

One fan point controlled by one, one way switch

One socket outlet 3 Pin, 6 Amp on independent board

One socket outlet 3 Pin, 6 Amp on same board.

One bell point controlled by one bell push.

M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 4 Sqmm (nominal area) in and including PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling including one run of PVC insulated FRLS copper conductor cable of 4 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board complete all as specified and directed.

S&F switch piano flush type single pole one way 5 Amp (ISI Marked) complete all as specified and directed.

S&F switch piano flush type single pole one way 15 Amp (ISI Marked) complete all as specified and directed.

S&F bell push flush type single pole one way 5 Amp (ISI Marked) complete all as specified and directed.

S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) complete all as specified and directed.

S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked ) complete all as specified and directed.

S&F switch piano flush type single pole two way 5 Amp (ISI Marked) complete all as specified and directed.

S&F bell multi music type AC, 230 Volts, single pole (ISI Marked) complete all as specified and directed.

S&F Electronic fan regulator 230 volts, step type, socket type, hum free 120 watt ISI Marked,including taking down unserviceable complete all as specified and directed.

S&F ceiling rose, surface Bakelite 65x17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) complete all as specified and directed.

S&F 10 Watt LED Bulk head fitting in engineering plastic housing with clear prismatic diffuser including LED 10 watt complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 complete all as specified and directed.

M&L for submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLSH wire 6.00 Sq mm 1100 volts grade including and 6.00 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in rigid PVC conduit 25mm bore complete all as specified and directed. Note : Two run of 6.0 Sqmm cable and one run of 6.0 Sqmm cable as earth continuity conductor and 25mm rigid PVC conduit shall be measured and paid as one unit.

M&L for submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLSH wire 4.00 Sq mm 1100 volts grade including and 4.00 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in rigid PVC conduit 25mm bore complete all as specified and directed. Note : Two run of 4.0 Sqmm cable and one run of 4.0 Sqmm cable as earth continuity conductor and 25mm rigid PVC conduit shall be measured and paid as one unit.

M&L for submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLSH wire 2.50 Sq mm 1100 volts grade including and 2.50 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in rigid PVC conduit 25mm bore complete all as specified and directed. Note : Two run of 2.50 Sqmm cable and one run of 2.5 Sqmm cable as earth continuity conductor and 25mm rigid PVC conduit shall be measured and paid as one unit.

S&F MCB, 6 to 32 Amp, SP, 240 Volt complete all as specified and directed.

S&F MCB, 32 Amp, SPN, 240 Volt complete all as specified and directed.

S&F MCCB 25 to 100 Amps TP, 415 Volt 16 KA adjustable thermal & fixed magnetic setting Ics = 100% = 01 No complete all as specified and directed.

S&F surface and wall mounted LED tube light fittings of cap 10W , Two feet Basic all purpose surface and wall mounted LED batten with extruded aluminium housing & integrated electronic driver including taking down od old light fittings complete all as specified and directed.

S&F surface and wall mounted LED tube light fittings of cap 20W , four feet Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver including taking down of old light fittings complete all as specified and directed.

S&F prewired distribution board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 8way single pole and neutral, etc. complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed.

(i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Quoted rate of Item includes the cost of 7.50m GI pipe for protection of earth wire/strip Any variation in length shall be adjusted through deviation order. (iii) Quoted rate of Item includes cost of 7.50m earth lead wire/strip. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

Taking down carefully ceiling fan 230 volts single phase 50 Hz from the position after dismantling fan blades of any sweeps and carrying out complete servicing with and including cleaning, greasing, replacing flexible 3 core cable of size 1.5 Sqmm with copper conductor from ceiling rose to fan, replacing rubber reel, split pins, check nuts, PVC connector complete with and including painting with 2 coats of synthetic enamelled paint over a coat of red oxide anticorrosive primer after rubbing entire fan body and blades and fixing back the fan in position complete all as specified and directed.

S&F in repair single pole and neutral enclosure 2 module in sheet steel with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 10 KA complete all as specified and directed.

S&F factory made sheet metal enclosure for VTPN DBs, 4Ways, double door, class IP-43 I with built-in-bus bar complete suitable for 415Volts, AC, 50Hz supply, suitable for incoming MCCB and outgoing MCBs and fixed in recess in wall complete all as specified and directed.

S&F LED Street Light of Capacity 30 Watt With inbuilt Driver having Pressure die cast Aluminium housing, IP-66 Having Efficiency of ≥ 100 Lumens/Watt, Operating voltage – 120 – 270 Volts, P.F ≥ 0.95, T.H.D < 10 % , Suitable for 30 to 40 mm O.D Mounting Pipe and Suitable for mounting on Wall / Pole With Necessary Mounting arrangements ) including connecting up with three core twisted flexible copper conductor cable with suitable size, Mounting Pipe/Bracket, Nut,Bolts and Accessories including disconnected & taking down old unserviceable light complete all as specified and directed.

HINGLAZ ENTERPRISES

M/s RKG CONSTRUCTIONS

Paliwal Construction Company

Leelashah Enterprises