SPECIAL REPAIRS TO BLDG NO P80 P81 AND HARD

Amount

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including removal of debris to out side MD land complete all as specified and as directed.

M&L PCC 100mm thick,1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in sub base to floor including necessary form work and finishing the surface even and fair without using extra cement complete all as specified and as directed.

M&L PCC 75 mm thick,1:3:6 type C -1 by using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even and fair including filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified and as directed.

M&L PCC 100mm thick,1:2:4 type B2 by using 40 mm graded crushed stone aggregate as in floor including necessary form work and finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Demolition of floor hearth or wall tiling including cement mortar bedding and backing coat including removal of debris to out side MD land complete all as specified and as directed.

M&L Non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L Non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18Sqm, as in skirtings /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including backing coat of 10 mm thick in cement mortar 1:4 complete all as specified and as directed.

M&L Glazed coloured ceramic tiles of size 300 x 200 x 7mm thick on vertical surface of wall over and including 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white cement / coloured cement to match the tiles complete all as specified and as directed.

Complete removal of existing water proofing treatment of any description including bedding up to the true surface of original concrete, in RCC roof slab / stone patty and roughening the old surfaces by picking, sweeping clean and washing down with water to remove dust etc including removing rubbish to out side MD land and provide plastring 10 mm thick in CM 1:4 over the RCC roof slab / stone patty for laying of water proofing treatment using water proofing compound (WPC) and including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastred surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm using butane torch with minimum 10cm side lap and 15cm end lap complete (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen confirming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. NOTE :- WPC shall be measured and paid separately under respective item. (e) FIFTH COURSE : Provide ISI marked 20-22mm thick hydraulically pressed cement concrete tiles of size 250X250mm laid over 15mm thick bedding in CM 1:4 , joints grouted and flush pointed in CM1:3 mixed with WPC as per manufacturer's instructions. NOTE :- WPC shall be measured and paid separately under respective item.

M&L rendering 15 mm thick in cement mortar 1:4 on fair faces of brick or concrete surfaces and finished the surfaces even and fair without using extra cement including taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of debris to out side MD land complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

Supply only water proofing compound

Complete removal of existing treatment of any description on walls and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and as directed.

Preparation of old decorated surfaces of walls and applying one coat of white wash complete all as specified and as directed.

Preparation of old decorated ceiling surfaces and applying one coat of white wash complete all as specified and as directed.

S&F 4mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each panes including hacking out old broken glass from metal frame complete all as specified and as directed.

Preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old painted wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed .

Taking down chowkats or frames (without taking of shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications and as directed .

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed .

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed.

M&L factory Made flush shutters, 35 mm thick solid core with particle board core construction as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 35mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

Butt hinge of size 100mm , medium weight, cold rolled mild steel, complete all as specified and as directed.

Aluminium alloy handles,anodised 150 mm size extruded , fabricated type, complete all as specified and as directed.

Aluminium anodised barrel tower bolts of extruded section of 200 mm size complete all as specified and as directed.

Aluminium alloy anodised sliding door bolt with hasp and staple [bolt type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F floor door stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

Preparation of new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F 500 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion and 20mm PTMT ball valve with epoxy coated aluminium rod high density platic ball screwed for iron pipe all as specified in SSR Part-I including dismantling existing concrete water tank complete all as specified and as directed.

S&F GI tubing (ISI marked) 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking down old tubing complete all as specified and as directed.

S&F GI tubing (ISI marked) 20mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking down old tubing complete all as specified and as directed.

S&F stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for union complete all as specified and as directed.

S&F stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 20mm bore iron pipe or for union complete all as specified and as directed.

S&F bib tap chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F 110 mm bore (SWR) PVC bends any radius complete all as specified and as directed.

S & F 75mm bore PVC [SWR] floor trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F 125 mm / 110 mm PVC gully traps, square or round mounted, Type 'S' including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] vent cowl complete all as specified and as directed.

M&L vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,anti- syphonage pipe, including provision of cement concrete bedding 1:5:10 type E2 complete and making good to floor match with existing floor/surfaces all as specified and as directed.

M&L PVC valve less, syphonic action type, flushing cistern, low level of 10 ltrs capacity , white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 by using 20mm graded crushed stone aggregate, 100mm thick as in flooring / for plat form for water tank on roof including necessary form work complete all as specified and as directed .

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed .

S&F Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and as directed.

M&L Granite slab 22 to 25mm thick machine cut, factory polished, Jet Black colour, as in steps, jambs, pillars, window cills, cooking platform, and like bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone complete all as specified and directed.

S&F hat and coat hook, brass solid body, 175mm to 250mm long complete all as specified and directed.

M & L chequered cement concrete tiles 30cm x 30cm x 25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry as in floors/ path etc over and including screed bed or bedding layer of 20mm thick in CM 1:6 complete all as specified and as directed.

S&F Rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, cooler stand etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars ,barred iron doors; ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Forming contraction (Dummy) joints 30mm deep x 10mm wide filled with sealing compound grade 'A' including necessary form work complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc . removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all as specified and as directed.

Disconnecting / terminating the ends of existing submain wiring / service cable up to 10sqmm from poles and removing burnt cable from site for keeping in safe custody or for taking credit complete all as specified and as directed.

Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all as specified and as directed .

M&L point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multi stranded copper conductor 1.5 sq mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including PVC casing & caping in wall / roof / floor etc, ISI marked with PVC terminal box fixed with cadmium plated screws with washers for mounting of switches, sockets and fan regulators etc, with and inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly for,one way switch One light/ fan/bell point controlled by one, one way switch 5Amps complete all as specified and directed .

All as per serial item No 57.00 above but for one ceiling fan / exhaust fan point controlled by one , one way switch 5Amps.

All as per serial item No 57.00 above but for one 3 pin socket outlet 5 Amps on the same board with other switches complete all as specified and as directed.

All as per serial item No 57.00 above but one 3 pin socket outlet 5 Amps on independent board complete all as specified and as directed.

All as per serial item No 57.00 above but for 15 Amps 5/6 pin socket point on independent board with 4.00 Sqmm PVC insulated FRLS multi-stranded copper conductor with 4.00 Sqmm PVC insulated FRLS multi-stranded copper conductor as earth wire complete all as specified and directed .

M&L factory made distribution board in sheet metal enclosure in double door with 200A rated copper bus bar,SPN 4 way, 240V complete all as specified and as directed.

M&L factory made distribution board in sheet metal enclosure in double door with 200A rated copper bus bar,SPN 8 way, 240V complete all as specified and as directed.

M&L MCB SPN ‘C’ Curve 10KA , 40 Amps 230V complete all as specified and as directed .

M&L MCB SP ‘C’ Curve 10KA , 6-30 Amps 230V complete all as specified and as directed .

M&L switch piano 5 Amp flush type single pole one way with ISI marked, complete all as specified and as directed.

M&L switch piano 15 Amp flush type single pole one way with ISI marked, complete all as specified and as directed.

S&F socket outlet 5 Amps 2-in-1,3/5 pin 230V AC flush type, complete all as specified and directed.

S&F switch socket outlet, multipurpose, 2 in 1, 5 and 15 Amps, flush type, universal , 230 V controlled by one switch complete all as specified and as directed.

S&F ceiling rose, surface bakelite, 65 x 50 mm, three terminals, 230 V complete all as specified and as directed.

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative round plastic bulk head LED luminaire comprising of high brightness LEDs, IP54 protection with lamp 10W 6000K with all accessories including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Make :- Havells Model No.LHEXCFP7PN5W010 or techno commercially equivalent make in Bajaj / CG / Philips

S&F lamp Holder, insulated body with back plate, 230 Volts for batten fittings complete all as specified and as directed.

S&F in repair LED Lamp 9 watt, 230 volts complete all as specified and as directed. Make : HPL Cat Part No.LTHPLEDLAMP9W/B22 or techno commercially equivalent model of make Bajaj/Philips/CG

S& F in repair integrated LED channel tube light fitting, 1X20W, 230V, energy efficient box type, integral, sleek polycarbonate with white acrylic cover epoxy powder coated with fluorscent tube light 1X20W complete with all accesories internally pre wired and connectiong up with twin core twisted flexible copper conductor of suitable size complete all as specified and as directed. Make :- Cat part No. DMLN1LT8-16 of make CG or Techno commercially equivalent model in make of Philips / Havells / Bajaj

Taking down ceiling fan ,any size and sweep from its position and taking out old burnout winding and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc including spray painting of ceiling fan, fan blades, down rod, canopy etc with two coats of synthetic enamel paint of white in colour including preparation of old painted surfaces, cleaning etc and writing the fan numbers etc., with black paint and replacement of worn out parts such as bearing,bushes,condenser, connector, flaxible cord,split pin etc., if required and re- assamble the same and fixing to position / location as directed, connecting to electric system, testing etc after repairing, complete all as specified and as directed .

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed by Engineer-in-charge. NOTE :(i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-( ii) Item includes the cost of GI pipe up to 7.5m for protection of earth wire. Any variation in length beyond 7.50 m shall be measured separately.(iii) Item includes cost of lead wire up to 7.5 m Any variation in length beyond 7.50 m shall be measured separately.(iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

Supply, laying, jointing, testing and commissioning 1100 volt grade heavy duty XLPE insulated LT under ground cable, sheathed, as per IS- 7098 (Part I) 1988, galvanized steel strip armoured heavy duty multi stranded aluminum conductor laid in trenches / passed through pipe/duct road crossing, fixed on poles/ wall with clamps made out of mild steel flat iron including fixing accessories like brass cable glands double compression type, lugs, nuts, bolts, washers etc of size 2 core 10 sqmm complete all as specified and directed

Kusum Traders

M.D. CONSTRUCTION CO.

National Rewinding Works

M/S Dharam Chand Lal Chand Jain

SOHANLAL MOHTTA