Upgradation Renovation of Dormitory Drivers rooms and adjoining area of Guest House

Civil Work

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

1 All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Cold twisted bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Make: Kajaria/NITCO/ RAK/JOHNSON

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed vitrified floor tiles polished finish of size

Size of Tile 600x600mm

Size of Tile 600 x 1200 mm

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer- in-charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead

Of area 3 sq. metres and below

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in- harge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately

Kiln seasoned and chemically treated hollock wood

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), withnecessary accessories and screws etc. complete.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete

Providing and fixing chromium plated brass door lock with handle of approved quality with necessary screws etc. complete as per approval of EIC

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading,transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen counters,window sills, acias and similar locations of required size of approved shade,colour and texture laid over 20mm thick base cement mortar 1:4(1cement 4coarse sand) with joints treated with white cement,mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edge to give high gloss finish etc.complete at all levels.DSR No.8.2

Granite of any colour and shade DSR No.8.2.3

Area of slab upto 0.50 sqm DSR No.8.2.2.1

Area of slab over 0.50 sqm DSR No.8.2.2.1

Providing and fixing soil, waste and vent pipes :

100 mm dia

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

75mm diameter

Centrifugally cast (spun) iron socketed pipe as per IS: 3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing and fixing collar :

Sand cast iron S&S pipe as per IS: 3989

Sand cast iron S&S pipe as per IS: 3989

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors

100 mm inlet and 75 mm outlet

Sand Cast Iron S&S as per IS- 3989

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including cutting chases and making good the walls etc.

20 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall:

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20 dia nominal bore

Providing & fixing of ball valve (brass) of approved quality High or low Pressure, with plastic floats complete;

20mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

20 mm dia nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. Brass extension nipple (size 15mm x 50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

100x100mm size P Type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x510 mm bowl depth 200 mm

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-incharge.

Providing and fixing C.P Pillar Cock long neck of Make Jaquar Model or equivalaent model of approved make.

Providing and fixing C.P Sink Cock long neck with swinging spout of Make Jaquar Model or equivalaent model of approved make.

P&F of wall hung wash basin with full/half pedestal complete with C.I. MS b

rackets, C.P. waste 32 m.m. as per standard pattern i/c cutting and painting of brackets and making good the wall complete in all respect. Make Jaguar or equivelent as per approval of EIC

Providing and fixing CP Bottle Trap (with internal partition) 32mm size with wall connecton pipe & wall Flange complete in all respect as per Makes approved by EIC.

Providing and fixing Regular body of concealed stop cock suitable for 15mm pipe line with protection cap with exposed parts complete in all respect make as approved by EIC.

Providing and fixing C.P wall mixture with provision of overhead shower with 115mm long bend on upper pipe, connecting legs & wall flanges og jaquar make or equivalent make as per approval of EIC complete job

Providing and fixing C.P. angle valve with wall flange of Make Jaquar or equivalent model of approved makes

Providing and fixing C.P Bib Cock with wall flange of Make Jaquar Model or equivalaent model of approved make.

Providing and fixing of looking glass with PVC or wooden beading complete in all repect with screw/nut dip/plug

Providing and fixing of C.P. towel ring of Make Jaquar Model or equivalent model of any other approved make.

Providing and fixing of C.P. Towel Rail 600 mm of Make Jaquar Model or equivalent model of any other approved make.

Providing and fixing CP Brass soap dish complete in all respect.

Providing Drip Seal joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :

Providing and fixing of GI Tank Nipple of size 20 mm dia of approved make complete

P&F of under counter oval wash basin . complete in all respect. Make Jaguar /Cera or equivelent as per approval of EIC

providing and fixing of pressimatic pillar cock with auto closing system complete in all respect make Jaguar, Cera, Hindware

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Renewing glass panes and refixing existing wooden fillets:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)

100 mm dia

Providing and fixing plain bend of required degree.

Sand cast iron S&S as per IS : 3989

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710/HDMR Board of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in- charge.

Providing and fixing 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

providing and fixing of 6 mm thick HDMR of approved make i/c necessary nails screws adhesive etc. complete as per the direction of EIC

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710/HDMR Board of approved brand )including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.)( Century/ Greenply/Duro/ asian/Marino)

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing and fixing of soap dispensar complete in all respect.

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length

15 mm nominal bore

Providing and fixing of 3mm commercial ply on the doors

Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group B

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

4X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

1 x 1.5 sq. mm

3 x 1.5 sq. mm

3 x 2.5 sq. mm

3 x 4 sq. mm

3 x 6 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Bell push

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150nnm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings)

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MOB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way , Double door

4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MOB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MOB TPDB is normally used where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MOB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and neutral

Triple pole

Triple pole and Neutral

Supplying and fixing single pole blanking plate in the existing MOB DB complete etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Supply, installation, testing and commissioning of bulk head LED 10 watt IP65/66 fitting to be fixed on wall. Make and model of fitting as under Philips:- WT202W LED65 CW PSU S2 PC Bajaj: IVORA LED Bulk head 10W CDL Crompton: LBHP-10-CDL

Supply and fixing of 63 amp rating, 415V, 10KA"C" curve Three pole & Neutral miniature circuit breaker suitable for inductive load in the existing DB complete with connections, testing and commissioning as required.Makes Havels/ABB/Schnie

Supply and erection of Modular type DP switch 2 module 32 Amp 250 Volt on existing modular box, modular base and cover plate complete in all respect.Make Legrand (Arteor)/Schneider (Zencelo)/Crabtree (Murano)/ L&T (Englaze/ MK(Elements)/ (Cheiron)/ Gold Medal(GIFA)/ABB ivie

Supply and Installation of Surface mounted round LED down lighter 18 Watt, 6500K with necessary connections to the adjascent light point with all petty msterial and labour required to complete the job in all respect Make :- Bajaj/ Cropmton/Philips/Wipro

Supply,erection,testing and commissioning of ceiling fans 1200mm sweep one star rating white color with copper winding but without regulator complete with aluminium blades, plastic canoples 2 nos, double ball bearing, MS hanging rods, etc. complete in all respect. The job includes Installation, testing and commissioning of ceiling fan, including wiring with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required upto adjacent light point complete in all resepect. Makes Havells-Velocity ES/Orient-Summer -Breeze Pro/Crompton-High Speed/Bajaj- SABSE TEZZ-EE only

Supply and errection of 1x20 watt 4' long LED box type fittings with decortative end caps of make Crompton CAT no. DMLNILT8-16+LT8-20-865-2 or equivalent models of make Philips/Surya make only .The LED tube rod 20 watt polycarbonate with inbuilt driver, extruded aluminium heat sink, 50000 burning hours at 70% lumens maintenance of makes Philips/Havells/Wipro/Crompton/Bajaj. The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings etc. as requried to complete the same to the entire satisfaction of engineer in charge.

Supply and errection of 10 watt LED batten Extruded PC housing with inbuilt driver and polycarbonate diffuser of make Philips/Wipro/ Bajaj / Havells /Crompton only . The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings etc. as requried to complete the same to the entire satisfaction of engineer in charge.

Supply installation testing and commission of 250mm fresh air fan 1325- 1350 RPM in plastic body Off- white /White color. The job includes Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Makes- Bajaj-Maxima DXL-GO2/Crompton- Brisk Air /Havells-Ventil air- DX/Orient

Supply, installation, testing and commissioning of Inverter Split AC 2TR capacity, 3 star rating with Refrigerant R-410/R-32 Gas with with ISEER in range 3.80 to 4.39 , Cooling Capacitty >= 6200 Watt. AC shall be suitable for 230 Volts+- 10% Volt ,50 Hz, Single phase , other standard manufactures Specification including installaltion charges complete in all respect upto the entire satisfaction of Engineer-in Charge. Make :- Daikin/Carrier/Hitachi/ Voltas

Providing & Fixing of Powder coated ready made heavy duty out door stand for Split out door as per site requirement to the entire satisfaction of Engineer- in Charge.

Restoration of gas and Dismantelling of existing Split Air conditioner and reinstalation of the same with gas topping if required complete the job in all respect.

Providing and Fixing of 22 gauge soft copper piping of size 3/8” & 5/8” or as per original manufacturer of A/C size, for Liquid & Suction sides, between indoor & outdoor units with 6 mm thick nitrile rubber insulation & protective covering for exposed weather including cost of chasing brick wall/RCC wall & repairing to original condition.Make Rajco., Mandev, Totaline.

Providing and Fixing of PVC Rigid drain Pipe surface/recess in wall / floor with necessary repair to the original condition, complete in all respects from indoor unit to Disposal Points as directed by the E.I.C. Size ¾” including specials- Make- Diplast or Equalivent.

Providing & fixing of 4 core 2.5 sqmm flexible coppe wire ISI Marked complete. Makes Havell/Polycab as per site.