Re Tender of Annual repair and Maintenance or Services of Civil works for ESIS Hospital and Staff Quarters at Parwanoo Himachal Pradesh

Amount

Civil Manpower: (PART-I)

Supervisor Cum-Fire safety personnel

Plumber

Cleaner Sewerman

Gardener/Mali (on call basis)

Masson (On Call basis)

Carpenter (On Call basis)

Material and Labour :(PART-II)

Carriage of materials by mechanical transport including loading, unloading and staking up to 5 km. lime, moorum, building rubbish.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plam), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kind of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sokets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc and disposing of surplus excavated soil as directed, within a lead of 50 m: all kind of soils. Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia, But not exceeding 300 mm dia.

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidations each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Suppling and filling in plinth with Sabarmati sand floors including, watering, ramming, consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. all kinds of soils.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti- teramite treatment (excluding the cost of chemical emulsion) :Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:With chlorpyriphos / Lindane E.C. 20% with 1% concentration.

Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1cement : 2 coarse sand) to the full depth of the hole : With chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering – All work up to plinth level :

1:2:4 (1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size.)

1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size.)

Centering and shuttering including strutting, propping etc and removal of work for Foundations, footing, bases for columns

Brick work with F.P.S. Bricks of class designation 75 in foundation and plinth in : cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with F.P.S. Bricks of class designation 75 in superstructure above plinth level up to floor five level in all shapes and size in :cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills, facias and similar location of required size of approved shade, colour and texture laid over 20mm thick based cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edge give high gloss finis etc. complete at all levels. Granite of any colour and shade, Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. Complete

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S pressedbutt hings bright finished of required xize with necessary screws, per direction of Engineer-in-charge. Kiln seasoned and chemically treated hollow block.

35 mm thick shutters

Providing and fixing panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measure). Panelling for panelled or panelled and glazed shutters 25mm to 40 mm thick Particle board 12 mm thick

particle board 12 mm thick plain particle board

Pre-laminated particle board with decorative lamination on both sides, Grade. Type II IS:12823 marked

Float glass panes 4 mm thick

Float glass panes 5.5 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured)

Chequred precast cement concrete tiles 22 mm thick in foothpath & courtyard, jointed with neat rubbing slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete , on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand ). Medium shade pigment using 50% white cement , 50% ordinary cement

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Size of tiles 500 X 500 mm

Fixing glazed/Ceramic/Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS:15477, in average 3 mm thickness.

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level over first class kail wood strips 25*6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) : Flat surfaces

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap fir thermal expansion, (i) single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised – PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

75 MM coupler

110 mm coupler

75x75x75 mm single tee without door

110x110x110 mm single tee without door

75 mm bend 87.5'

110 mm bend 87.5'

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised – PVC rain water pipes by means of 50 x50 x50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortr 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. Complete.

on steel work

on concrete work

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand)

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge

Door chowkhats

window chaukhats

claearstory window chaukhats

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/rubbish to the nearest municipal dumping ground. For door/window/clarstory

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty.

Float glass panes of thickness 4 mm

Float glass panes of thickness 5.5 mm

Renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer

Renewing Wrought iron or M.S. Wheel or roller of steel door or gate and fitting and fixing the same with necessary clamps, nuts and bolts/welding and erection etc. Complete

wheel 50 mm dia and below

wheel above 50 mm dia

White washing with lime to give an even shade : old work ( two or more coats)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: old work (one or more coats)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work :

75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : one or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : one or more coats on old work.

Re-lettering with black Japan paint of approved brand and manufacture

Finishing walls with water proofing cement paint of required shade: Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

Finishing walls with textured exterior paint of required shade: Old work ( two or more coats on existing cement paint surface applied @3.28 litre/10sqm.

Melamine polishing on wood work ( one or more coat

Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i) Tank shall be emptied of water by pumping & bottom shall be cleaned of slit and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm dia for all depth.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer – in- charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer -in-charge. In cememt mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area 3 sqms and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material whthin 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Above 40 mm nominal bore metre

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge:

Up to 150 mm diameter

Above 150 mm dia up to 300 mm dia

Above 300 mm diameter

Dismanting old plaster or skirting ranking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing and fixing water closet squatting pan (Indian type W.C. Pan) with 100 mm sand cast iron P or S trap, 10 litre low level white device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requird. White vitreous china Orissa pattern W.C pan of size 580X480 mm with integral type foot rests

Providing and fixing white vitreous china pedstal type water closet (Europeaan type W.C pan ) with seat and lid , 10 litre low level white P.V.C flusing cistern , including flush pipe, with manually controlled device ( handle lever) , conforming to IS: 7231, with all fittings and fixtures complete , including cutting aand making good the walls and floors whrever required,

W.C pan with ISI marked white solid plastic seat and lead.

Providing and fixing white vitreous china water closet squatting pan (Indian type), Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing solid plastic sat with lid for pedestal type W.C pan complete:White solid plastic seat with lid

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400mm.

Providing and fixing wash basin with C.I brackets, 15 mm C.P brass waste of standerd pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous china wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing soil, waste and vent pipes :100 mm dia, Cetrifugally cast iron socket & spigot (S &S)pipe as per IS: 3989 , 100mm dia

75 mm Dia, Centrifugally cast iron socketed pipe as per IS:3989

Providing and fixing single equal plain invert branch of required degree:

100x100x100 mm sand cast iron S & S as per IS 3989

75x75x75 mm sand cast iron S & S as per IS 3989

100 mm sand cast iron S & S as per IS 3989

75 mm sand cast iron S & S as per IS 3989

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fitting of diameter :

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors . 100 mm inlet and 75 mm outlet, 100 mm inlet and 75 mm outlet. Sand cast iron S&S as per IS - 3989

Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work :

15 mm diameter pipe

20 mm diameter pipe

25 mm diameter pipe

40 mm diameter pipe

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete:

150 mm diameter

250 mm diameter

300 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. Pipes including bed concrete as per standard design :

150 mm daimeter S.W pipe

250 mm daimeter S.W pipe

Providing and fixing square- mouth S.W. Gully trap class SP-1 complete with C.I. Grating brick masonry chamber with water tight C.I. Cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be ot less than 2.70 kg as per standard design : 100x100 mm size P type.

100x100 mm size P typ, .With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

150x100 mm size P typ, .With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Dismantling of old S.W. Pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead abd disposal of unserviceable materials into municipal dumps :

150 mm diameter

250 mm diameter

300 mm diameter

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg),With F.P.S. bricks with class designation 75

Extra for depth for manholes, With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P. brass/ stainless steel screw, all complete as per architectural drawings and the directions of Engineer-in charge. For fixed protion, Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately), Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minium anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Chipping of unsound/weak concrete material from slabs, beams,columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge

50 mm average thickness

25 mm average thickness

Providing and fixing Vertical window blinds size 100 mm, 100% polyster.

Supplying Material: (PART-III)

Portland Cement (OPC43)

Oxidised mild steel door latch 250x20x6 mm

Oxidised mild steel handles 125 mm

White Cement

Fine Sand

Bricks (F.P.S)

Table rubber polished stone 18 mm thick (75x50 cm) Granite stone- 18 mm thick

Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/smt)

Float glass sheet of nominal thickness 5.5 mm (weight not less than 13.50 kg/smt)

Hydraulic door closer bottle type M.S. body with necessary accessories and screws complete (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm)

Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm

Prelaminated particle board with both sides decorative lamination, flat pressed 3 layer & grade (medium density) Grade I, Type II conforming to IS: 12823 (exterior grade), 12 mm thick

Anodised aluminium sliding door bolt 250x16 mm

Anodised Aluminium tower bolt (barrel type) 200x10 mm

Anodised Aluminium tower bolt(barrel type) 150x10

Anodised Aluminium handles 100 mm with plate 150x32 mm

Anodised Aluminium handles 125 mm with plate 175x32 mm

Decorative plywood 4 mm

Standard holder bat clamps for sand cast iron or cast iron pipes 150mm dia

Mild steel round bar 12 mm dia and below

Structural steel such as tees, angles channels and R.S. joists

Flats up to 10 mm in thickness

Second class teak wood in planks

Wire nails

Tile fixing chemical adhesive

C.I. bracket for wash basin and sinks

8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre long with S.S. tringular plate for Eureopean type W.C.

Clamps and M.S. stays including bolts and nuts for 100 mm pipe

Clamps and M.S. stays including bolts and nuts for 50 mm pipe

Clamps and M.S. stays including bolts and nuts for 75 mm pipe

Rubber insertions for 75 mm dia pipe joints

Rubber insertions for 100 mm dia pipe joints

Vitreous china pedestal for wash basin

G.I. inlet connection

GI Union ½” dia

GI Union ¾” dia

GI Union 1” dia

GI Union 1 ½” dia

Stoneware pipes grade A (60 cm long) 150 mm dia

Centrifugally SCI(spun) S & S P or S trap

H.P. or L.P. ball valve with polythene floats: 15 mm dia

20 mm dia Gunmetal gate valve with wheel

Vitreous china flat back wash basin 630x450 mm

Brass full way valve with C.I. wheel (screwed end) 25 mm dia

Brass full way valve with C.I. wheel (screwed end) 32 mm dia

Brass full way valve with C.I. wheel (screwed end) 40 mm dia

Brass full way valve with C.I. wheel (screwed end) 50 mm dia

Brass full way valve with C.I. wheel (screwed end) 65 mm dia

Brass full way valve with C.I wheel (screwed end) 80 mm dia

Gunmetal non-return valve-horizontal (screwed end) 80 mm dia

Vitreous china foot rests 250x125x25 mm

Brass cupboard lock 6 levers of approved quality, 40 mm size

Brass cupboard lock 6 levers of approved quality, 50 mm size

Weather/structural non sag elastomeric PU sealant (600ml Sausage) for joints in RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum/ Alluminium work complying to ASTM C920, DIN 18540-F & ISO 11600 incl all taxes.

EPDM Gasket in Kg (Above 60 g / m)

Anchor Fastner - M10

Galvanised steel corrugated sheets

Stainless steel (Grade-304)hollow section round/square tubes

Stainless steel bolts/square bar and plates

Mobil oil

Oxidised mild steel parliamentary hinges 100x125x27x2.8 mm

Brass 100mm mortice latch and lock with 6 levers without pair of handles

Pair of Anodised Aluminium lever handles for 100 mm mortice latch and lock

Chromium plated brackets (curtain rods)

Chromium plated Brass curtain rod 25 mm dia 1.25mm thick

Oxidised mild steel double acting spring hinges 100 mm

Rectangular shape 453x357 mm Mirror with Plastic moulded frame

UPVC plain shoe 75 mm bend

UPVC plain shoe 110 mm bend

Superior quality road marking paint (water based)

Corner angle 45x45x5 mm 2.50 m long

Flushing Cistern P.V.C. 10 litre capacity (low level) (White) (with fittings,accessories and flush pipe)

Brass hasps and staples (safety type) 90 mm

Chromium plated Brass Wardrobe Knob 50 mm

Second class teak wood in scantling

Vitrified floor tile 60x60 cm

C.I. grating 150mm dia weighing not less than 440 gm

Water proofing materials

S.C.I. gully or nahani grating

White plastic seat (soild) with lid C.P brass hinges and rubber buffers

C.P. brass waste 40 mm

Flexible (coil shaped) PVC waste pipe for sink or wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings

Bottle Trap

Unplasticised P.V.C connection pipe with brass union 45 cm long 15 mm bore

C.P. Brass Bip cock 15 mm

C.P brass long body bib cock 15 mm

C.P. brass stop cock (concealed) 15 mm

C.P. Brass angle valve 15 mm

12 mm M.S. 'U' beading

PTMT Ball Cock 15mm complete with Epoxy Coated Aluminium Rod & H.D. Ball

Salem Stainless steel AISI - 304 (18/8) Wash basin 530mm X 345 mm

C.I. cover without frame 300x300 mm inside i/c cover of 4.50 kg

Rectangular cover 455x60 mm with frame (low duty)

Rectangular cover 455x610 mm without frame (low duty)

C.I. grating 150x150 mm

560 mm dia cover without frame (Heavy duty)

EPDM Gasket for uPVC window/door

Fibre glass cloth

PTMT STOP cock 15 mm dia MALE THREAD

20 mm dia PTMT stop cock

PTMT push cock 15 mm dia

Wedge expansion hold fastener 3/8" or 10 mm

PVC Connection pipe 15 mm dia 1’-6” long

GI Tee 1” x 1” dia

G.I. inlet connection

Bright finish M S Butt hinges 124 x 65 x 2.12 mm

Wire nails

White plastic seat (soild) with lid C.P brass hinges and rubber buffers

Supplying & Providing G.I. pipes

15 mm thick, light weight,fully perforated square/butt edge integral densified,false ceiling tiles of size 595x595 mm.

GI Tee ½ “ x ½ ” dia

GI Tee ¾ “ x ¾ ” dia

GI Tee 1 ½ “ x 1 ½ “ dia

GI Elbow ½ “ dia

GI Elbow ¾ “ dia

GI Elbow 1 “ dia

GI Elbow 1 ½” Dia

GI Coupline ½” dia

GI Coupline ¾” dia

GI Coupline 1” dia

GI Coupline 1 ½” dia

GI Nipple ½” dia 2 inch long

GI Nipple ¾” dia 2 inch long

GI Nipple 1” dia 2 inch long

GI Nipple 1½” dia 2 inch long

GI Nipple ½” x 4 inch long

GI Nipple 3/4” x 4 inch long

GI Nipple 1” x 4 inch long

GI Nipple ½” x 6 inch long

GI Nipple 3/4” x 6 inch long

GI Nipple 1” x 6 inch long

GI Nipple 1 ½” x 6 inch long

GI Reducer elbow ½” x ¾”

GI Reducer elbow ¾” x 1”

GI Reducer elbow 1” x 1 ½”

GI Reducer tee ½” x ¾”

GI Reducer tee ¾” x 1”

GI Reducer tee 1” x 1 ½”

GI Reducer coupling ½” x ¾”

GI Reducer coupling ¾” x 1”

GI Reducer coupling1” x 1 ½”

Stainless steel Grab Bar ISI approved brand

Water meter 20 mm size

supplying AA MN1500, 1.5V Battery for black box urinal sensor of approved brand

C.P push cock sparrow

G.I plug

15 mm dia

S.S Waste coupling of ISI approved brand.