PROVISION OF HYGIENE CHEMICAL AND POL STORES AT SMC OF IAM AND CERTAIN SANCTIONED WORKS AT IAM UNDER GE AF MARATHYAHALLI

Amount

Taking down cement plaster on brick or stone walls or concrete surfaces including racking out joints, hacking for key and scrubbing down with water etc complete

M&L for 1:3:6 type C1 with 20mm graded crushed stone aggegate as in Pre-cast cement concrete block masonry with solid blocks, exc.10cm in width and setting in mortar 1:6 complete.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces finished even and fair without using extra cement in cement mortar 1:4.all as specified and directed

Taking down and refixing in the same operning of Shutters of any description exceeding 1 Sq.m and n exc 2 Sq. m each complete all as specified and as directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick(Horizontal or sloping) complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete as specified.

M&L for RCC 1:2:4 nominal mix type B1 using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type, table rubbed and polished) in steps, jambs, pillers window cillls , cooking plateform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade Granite

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm grade aggregate) as in levelling coarse in flooring finished even and fair under floor finishes. Including chipping of existing floor complete all as specified and directed

M&L for non skid coloured ceramic colour tiles 7 to 8 mm thick (Square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of coloured tiles over and including cement screed or bedding layer of cement mortar 15 mm thick in cement mortar 1:4 all as specified and as directed .

M&L for glazed ceramic coloured tiles in vertical surfaces of 350X250X7 mm / 450 X 350 X 7 mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 10 mm thick cement plaster in 1:3 as backing coat all as specified and directed

S&F sink without draining board made of stainless steel 1 mm thick kitchen or laboratory with plugs , washers and waste , including bedding in cement mortar on to dwarf wall or including fixing cantiliver brackets and connecting union to pipe , overall size 495mm x 420 mm & bowl size 410mmx330mm x 160mm complete all as directed

S&F in repair 32 mm waste fittings brass CP for glazed ware sinks, basins etc. with long screwed shanks and fly nuts, flangee end bedded in red lead cement and other end fixed all as specified and directed by Engr-in-Charge

S&F in repairs 32 mm bore flexible waste pipe for wash basin and kitchen sink complete all as specified and directed.

S&F in repairs Grating 150mmx150mm made out of stainless steel complete all as specified and directed.

S&F of 16 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fitting fixed complete to walls, ceiling or laid in floors etc including short length , with all pipe fittings such as ends, elbow, unions, tee, reducing tees etc. including taking down all as specified and directed by Engr-in-Charge

Description all as per item no 17 above but 20 mm bore.

S&F in repair Chromium plated fancy type bib taps with wall flange, cast copper alloy with round operating knob screwed down high pressure, screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repair stop valves/angle cocks or two way angle cock cast copper alloy concealed type long body with round operating knob chromium plated screwed down high pressure, screwed both ends for 15 mm bore iron pipe or brass ferrule.

M & L for preparating surfaces of plastered or unplastered surfaces of wall and applying two coats of oil bound distemper complete all as specified & directed by Engr-in charge .

Surface dressing n exc15 cm deep in soft loose soil complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, in hard/dense soil, getting out, removing surplus soil.

Excavation in trenches n. exc 1.5m wide and n. exc. 1.5m depth for foundation and getting out in hard/dense soil complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in foundation filling in mass concrete complete all as specified and as directed..

M&L for Providing precast cement concrete solid building blocks or slabs 10cm thick in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate (with plain or interlocking joints as directed)setting in cement mortar 1:6 mortar complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in foundation complete all as specified and as directed.

M&L for hard core of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick each, watered and rammed to a true surface complete all as specified and as directed.

M&L 75 mm thick cement concrete 1:4:8, type D-2, (40mm graded aggregate) as in sub base in floors complete all as specified and as directed.

M&L 100mm thick cement concrete 1:2:4, Type B-1using 20 graded crushed stone aggregate finished even and smooth without using extra cement complete all as specified and as directed.

Forming construction joints (Dummy) 65 mm deep x 10mm wide,filled with sealing compound Grade A complete all as specified and as directed.

S&F Plate girder or single stanchions,built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections with structural steel confirming to Fe-410W(Gde-E-250) quality A complete all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates with structural steel confirming to Fe-410W(Gde-E-250) quality A complete all as specified and as directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment

S&F of strucural steel for wind ties, grills, gratings, guard bars etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for preparation of new surfaces of steel & iron of any description, not otherwise described, over 10cm width or girth and applying 2 coats of synthetic enamel paint over a coat of red oxide primer.

S&F Prepainted galvalume aluminium zinc coating GI based corrugated/ Trapezoidal profile steel sheet 0.5mm thick of an approved colour having tensile strength of 550 Mpa as in roof covering in any curvature, fixed with self tapping screws complete all as specified and as directed.

M&L for preparation of plastered or un plastered surfaces on walls and applying two coats of cement paint over a coat of alkali resistant primer.

M&L for preperation of new plastered surfaces and applying two coats of synthetic enamel paint over a coat of priming paint plaster coat all as specificed

Returning, filling in any type of soil, including spreading, leveling, watering and well ramming in layers not exc 25 cm each complete all as specified and as directed.

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Demolition of cement concrete(unreinforced) in ground floors and pavings n exc 15cm thickness (Below or above ground level) complete all as specified and as directed.

Removing excavated material to a distance 250m but n.exc 500m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

M&L for RCC 1:2:4 nominal mix type B1 using 20mm graded crushed stone aggregate as in beams, cantilevers, bresummers, lintels over 1.5m span complete all as specified and as directed.

M&L for mild steel TMT bars 6 to 8 mm dia , cut to length, bent to shape required, including cranking, bending spirally, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete as specified.

Ditto as item No 45 above but 5 to 10mm dia as in stirrups, spacers and binders

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings etc flat rough rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads and the like rough finished surfaces of concrete complete all as specified and as directed.

S&F of framed work as in doors or gates of angle or other sections with gusset plates etc complete drilled for fixing steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive of steel sheetingor other covering) confirming to Fe-290 (Gde- E-165) complete all as specified and as directed.

S&F of welded steel wire fabric weight n exc 4Kg per Sqm supplied and fixed to steel members complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in CM 1:6 finished even and fair without using extra cement complete all as specified and as directed.

M&L for two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered surfaces including preperation complete all as specified and as directed.

S&F of pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

S&F of anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing complete all as specified and as directed.

S&F anodised aluminium door shutters aluminium section weighing 0.55Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed.

S&F anodised aluminium window and ventilator shutters side/sliding shutters without sash bars,aluminium section weighing 0.55Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, etc complete all as specified

S&F 4mm thick sheet glass ordinary quality and glazing in panes not exc 0.5 Sqm all as specified and directed.

M&L for machine cut Kota Stone slab for flooring using 20-25mm thick stone slabs over cement screed base in CM 1:4 20mm thick set and jointed in neat cement slurry and pointed in coloured or white cement to match the shade of stone slabs complete all as specifed.

Material & labour for concealed Wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through in stove enamelled steel conduit incl accessories incl provision of 1.5 Sqmm FRLS PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed by Engr-in-Charge.

Supply and Fixing of Flameproof cum Waterproof LED Bulk Head light fitting of 15W, IP66 protection of Cast Aluminum alloy material and Heat and Impact resistance toughen 'A' clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fix switch flame proof rotary type with termination box in LM6 16 A single pole 250 V controlled by three light fittings complete all as specified and directed by Engr-in-Charge.

Supply and fix flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Flame proof exhaust fan 300 sweep single phase 230 V with louver shutter complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanized iron or steel plate electrode 600 mm x 600 mm x 6.0 mm buried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to GI earth earth wire 4mm by means of GI bolts, nuts, check nuts and washers, earth wire protected by galvanized steel pipe 15 mm bore (light grade) connected to machinery/ equipment all as shown in Electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore light grade GI pipe for watering funnel wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified and directed by Engr-in-Charge.

Supply and Fixing MCB DB SPN 4 way, Double door, 240 V, AC, 50 Hz, with 200Amp rated bus bar IP-43 protection conforming to IS-13032, complete all as specified and directed by Engr-in-Charge.

Supply and Fixing in repairs MCB SP 5 to 25 Amps rating, 'C' series, 10 KA breaking capacity, 240V, 50 Hz AC complete all as specified and directed by Engr-in-Charge.

Supply and Fixing in repairs MCB SPN 25 Amps rating, 'C' series, 10 KA breaking capacity, 240V, 50 Hz AC complete all as specified and directed by Engr-in-Charge.

Supply and fixing sintex box hinged door size 500 x300 x230 mm (inside diamenson) for housing SPN DB and flame proof switches complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 m depth and not exceeding 1.5m width and getting out insoft/loose soil for laying of cable complete all as specified and directed by Engr-in-Charge. .

Supply , laying and testing cable XLPE insulated screened PVC sheathed armoured heavy duty electric cable with alluminium conductor 1100 V grade of size 10 sqmm 2 core complete laid in trenches/fixed wall etc complete all as specified and directed by Engr-in-Charge.

S & F sub class burnt bricks for cable protection complete all as specified and directed by Engr-in-Charge.

M&L for riddled sand cushioning to UG cable on layer of 8 cm thick before laying the cable and second layer of 15 cm thick after laying the cable complete all as specified and directed by Engr-in-Charge.

Supply and laying GI tube light grade 25 mm bore with clamps and all other fittings including nuts and bolts in order to fix on wall /floor complete all as specified and directed by Engr-in-Charge.

M&L for sub main wiring with Two runs of single core pvc insulated cable FRLS with copper conductor multistranded 1100 volts grade 4 sqmm through and including with suitable size of PVC conduit and its accessories , on surface including one run of 4 sqmm pvc insulated multistranded copper earth contuinuity conductor and connected to common earth dolly complete all as specified and directed by Engr -in-Charge.

Supply and fix electric water heater, storage type steel body with SS inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipes etc. complete all as specified and directed by Engr -in-Charge.

S&F PVC hot water connections pipe 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engr -in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 A complete all as specified and as directed.

Supplying and laying of CPVC pipes 16 mm bore SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S & F stop valve ,cast copper alloy, screwed down, high pressure with cructh or butterfly handle screwed both ends for iron with union fixed for 16mm bore CPVC pipe complete all as specified and as directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly-nuts, screwed for CPVC pipe and fixed complete all as specified and directed by Engr -in-Charge.

Cutting & screwing existing steel / PPR pipe for alternation or addition for 16 mm dia CPVC pipe complete all as specified and directed by Engr -in-Charge.

VSHVAS CIVIL AND ELECTRICAL SERVICES PRIVATE LIMITED

AishwaryaConstructions