No. CE/CW/30/2020-21-BusBays

Amount

Clearing and Grubbing Road Land .(Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to beused or auctioned up to lead of 1000metres including removal and disposal of top organic soil not exceeding 150mm thickness.i)By Manual Means:- A. in area of light jungle

Dismantling of Structures (Dismantling of existing structure like drains and culvert) ii) Dismantling Brick Tile Work

Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal upto 1000 metres. (Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes,in accordance with requirements of lines, grades and cross sections,loading and disposal of cut road with in all lifts and leads upto 1000 metres)

Removal of Unserviceable Soil with Disposal upto 1000 metres (Removal of unserviceable soil including excavation, loading and disposal upto 1000 metres lead but excluding replacement by suitable soil which shall be paid separately as per clause 305.)

Cutting of Trees, including Cutting of Trunks, Branches and Removal: Cutting of trees, including cutting of trunks, branches and removal of stumps, roots, stacking of serviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression/pit as per MoRT&H cl. no. 201. (i) Girth from 300mm to 600mm.

Cutting of Trees, including Cutting of Trunks, Branches and Removal: Cutting of trees, including cutting of trunks, branches and removal of stumps, roots, stacking of serviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression/pit as per MoRT&H cl. no. 201 .(ii ) Girth above 600mm to 900mm.

Cutting of Trees, including Cutting of Trunks, Branches and Removal: Cutting of trees, including cutting of trunks, branches and removal of stumps, roots, stacking of serviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression/pit as per MoRT&H cl. no. 201 .(iii) Girth above 900mm to1800mm.

Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction.)

Construction of Subgrade and Earthen Shoulders (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table (300-2) (a), ( Including cost of testing of materials at site and laboratory as directed by the deptt.) a) from private land Extra lead beyond initial lead of 3km @ Rs.8.46 per km = 10km

Granular Sub-base: B)By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density,complete as per cl. 401( Including cost of testing of materials at site and laboratory as directed by the deptt.)

Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fillup the interstices of coarse aggregate,watering and compacting to the reqd. density ( with an initial lead of 5.0 km. ) '

Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fillup the interstices of coarse aggregate,watering and compacting to the reqd. density ( with an initial lead of 5.0 km. ) '

Providing and laying interlocking (Colour) Concrete Block Pavement (ICBP) conforming to IS: 15658-2006 including all lead & lift complete as per technical specification and as directed . A) 80mm thick interlocking precast blocks having compressive strength of 40N/sq.mm

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Providing fitting & fixing in Anti skid paver tiles as per BIS specification of size (340mmx340mmx25mm) as directed and approved by the Deptt.

Providing, fitting and fixing in position of Ornamental Iron Grill of size 1500 x 750 mm at footpath as directed by engineer in charge and approved by the Deptt.

Providing and fixing in position Double Kerb Stone(GEMS) as per BIS specifications of size (300 mm x 450 mm x 100 mm) in proper level and grade at Footpath Edges, Divider Block etc. as directed and approved by the Deptt.

Construction of Boundary Wall -- Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.Upto a depth of 2 mts. below the existing Ground Level

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) , In substructure up to plinth level, Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level., Without using admixture, plasticiser, M20 grade concrete or Prop. 1:1.5:3

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) , In super structure from plinth level up to 1st floor level. , Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing.., Without using admixture, plasticiser, M20 grade concrete or Prop. 1:1.5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc., Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in Sides of tie beams, grade beams etc. at or below ground level., Using 25mm thick plank

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth upto 1st floor (Protruding M.S Rod/ Torsteel of column to be embedded in cement mortar and will measured and paid separately), 112 mm thick brick wall, In cement mortar in proportion 1:4 ( 1 cement: 4 sand)

15 mm thick cement plaster in single coat on fair side of brick / concrete for interior plastering upto 1st floor level including arises, internal rounded angle chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed., In cement mortar 1:4

Providing two coats of acrylic water based wall putty/ wall filler of Asian Paints/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the help of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Painting Two Coats on New Concrete Surfaces’ Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces.

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Dry rubble Flooring, Construction of dry rubble flooring at cross drainage works for relatively less important works.

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 mix with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Supplying, fitting and placing TMT IS:1786 Fe500 D bar reinforcement in foundation complete as per drawing and technical specifications. B) TMT-IS1786(Fe-500D) Secondary producer (ISI Approved)

Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork. F)RCC M25 Case I Using concrete mixer

BEAMS AND JOISTS Steel work riveted and/ or bolted/ riveted in built up sections, frame work including cutting, hoisting, fixing in position and applying a priming coat of red- lead paint up to 4.6m height above plinth including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed.

ROOF TRUSS Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Painting on Steel Surfaces (Providing and applying two coats of ready mix paint of approved brand on steel surface after through cleaning of surface to give an even shade)

Providing Pre Painted Galvalume Sheet Roofing (PPGL) at all levels including fitting and fixing self drilling, self tapping screws complete (Roof trusses, purlins etc. to be measured and paid separately.)

Stainless steel waiting bench of approved brand as directed by the department.

Ceiling with Exposed Metal (G.I.) Frame work with E-Grid - 2430 Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm . Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid, all complete as per the drawing & directions of engineer-in-charge. Finally, if specified, boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid.(A) Standard Ceilings of Everest make or equivalent as directed by the departement(ii) Using 6 mm thick FC Board

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Work (Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirts, dusts and other foreign matter, demarcation at site and traffic control.)

Providing reflective pavement marker with micro prismatic lens in both direction having thermoplastic body adhering to the specification and guidelines of MoSRT&H's fixed to the road surface using the adhesives and the procedures with three months replacement warrenty and free maintenance.

Providing ‘Sparkle Solar Road Studs, manufactured by Tata B.P. Solar India Ltd. Of size (125mm x 125mm), 90mm height (from bottom of shank to the top of stud) with detachable battery, m6LEDs-three on each side for Bi-directional studs/ 3 LEDs on one side for unidirectional studs, ultra bright LED in amber and red colour, weight per stud 700+25 gms, flash rate of 50-65 times per minute completely water resistant and weather proof with replacement warranty and free maintenance for one year from the date of installation of stud on road-(installation should be made using adhesives and procedures recommended by manufacturer under the supervision of their competent technician).

Providing spring post of 750mm height, 80mm dia with round base of 200mm dia made of poly urethane with 3 white reflective bands made of HIG retro-reflectorised sheeting and fixing to the ground as per specifications of manufacturers

Tree reflector made of heigh intensity grade retro-reflectorised sheeting fixed over aluminium sheeting of 2mm/0.28mm thick firmly fixed with necessary galvanized nail. 150mm dia/150mmx150mm.

Providing metal tubular delineator (50mm dia and 1.25mm thick) with 15cm reflector made of heigh intensity grade retro reflectorised sheeting around the pipe at top covered with wire mesh of 20cm length with two nos of similar reflective bands and bottom fastener M.S. angle including firmly fixing the delineator to the ground by means of CC(M-15) foundation of size-(25cmx25cmx25cm), 25cm below ground to the true line and level as directed by the deptt. With six months replacement warranty and free maintenance., 1000mm height.

Direction and place identification sign upto 0.9sqm size board. Providing and erecting direction and place identification retro-Reflectrorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3 fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9sqm fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand)

Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart, 1.8 m overhang on both sides if fixed in the median and on one side if fixed on the footh path , fixed with sodium vapour lamp and fixed on the concrete foundation.

Overhead Sign Board Providing retro reflective sign board of high intensity grade reflective sheeting conforming to ASTMD4956 B-III specifications having approved pattern over its entire surface bonded on to 2 mm thick aluminium sheeting, the entire face of the sign shall be covered & bounded with yellow/ white/ red/ blue high intensity grade with distinctive nod pattern on front side with heat lamp vacuum applicator machine only.

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) 90cm equilateral traingle

60cm circular

90 cm high octagon

SOCKET OUTLET Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete MODEL RANGE LEGRAND (MYRIUS), ANCHOR(VIOLA), MK (WRAPAROUND/PLUS), ABB (CHEIRON), KOLORS(KREST), SCHNEIDER(VIVACE), CRABTREE as per direction of department.

MCB DB Supplying fitting and fixing Industrial plug and socket in surface mounting SPN sheet steel powder painted MCB DB incorporated with MCB Din rail, neutral link, earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the department. 20A capacity.

Supplying with fitting and fixing 4P 10 KA 240/415 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB Schneider MG, legrand, Hager, Crabtree Xpro make) 63A

WIRING Wiring for light/fan/call bell point with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial(multistrand) cable FR conforming to ISI-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade upto 1100 volts (Finolex/RR Kabel/Nicco/Anchor/or equivalent Make as approved by the Deptt.) in surface/recessed conduit wiring system with 20mm dia 2mm thick/heavy rigid PVC IS:9537 Part-III conduit(Berlia/AKG/Precision/Presto Plast/ Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push/(Anchor penta/Gold medal/Kolor kany.kom/Havells or equivalent make as approved by the Deptt.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rose (Anchor penta/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. Complete, Long point up to 10.00 metre. Length.

Wiring for drawing sub-main line with 2 x 4 sq.mm + earth continuity with 1 x 2.5 sq.mm cable in 20mm.dia rigid ISI marked hot dip galvanized pipe

WALL FAN Supplying including fitting fixing of following AC wall fan in the wall of following sweeps with making necessary connection as approved by the department as required complete and as directed by the department. Air Circulator wall fan 450 mm sweep Turbo force, ORIENT make or equivalent Usha make Air Circulator wall fan 450 mm sweep Turbo force

Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30cm apart

‘Maintenance of Hedge for one year

Planting of Trees and their Maintenance for one Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for one year.

Making Tree Guard 53 cm dia and 1.3 m high as per design from empty bitumen drum (Making tree guard 53 cm dia and 1.3 m high as per design from empty bitumen drum, slit suitably to permit sun and air, (supplied by the department at stock issue rate) including providing and fixing 2 nos MS sheet rings 50mmX0.5mm with rivets, complete in all respects.

Installation of Dustbin as directed and approved by the department

Women Modular Toilet Stalls (With all accessories) Single

Grid connected solar PV System (5kW) as directed by the departmnet

Dismatling of existing Bus stop as directed by the department

Shifting of Pipelines

Shifting of Telephone / Electric Poles and Lines (Shifting of telephone / Electric poles including excavation,dismantling of foundation concrete and construction under the supervision of concerned department, disposal with all lifts and up to a lead of 1000 metres and stacking serviceable materials and unserviceable materials separately.)

Joy Charan Barman