SPECIAL REPAIR TO BLDG NO T-29, T-30 AND T-82 AT JAISALMER MIL STN

Amount

Dismantling Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & directed by Engineer-in-charge.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed by Engineer-in-charge.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar, complete all as specified & directed by Engineer-in-charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed by Engineer-in-charge.

Precast cement concrete block masonry with solid blocks PCC Type C1 (1:3:6) (using 20mm graded aggregate) exc 10cm in width and setting in CM 1:6 complete all as specified & directed by Engineer-in-charge.

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified & directed by Engineer-in-charge.

Extra over to stone walling for hammer dressing to face stones and dressing of the face beds & joints as specified of squared rubble walling regular coursed, Jodhpur type, with maximum depression of face from straight edge held against the dressed surface n.exc. 20mm complete all as specified & directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zine coating GI based corrugated steel sheeting 0.50mm thick any colour having tensile strenght 550Mpa in roof coverings fixed with self tapping screws including dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, all as specified & directed by Engr-in-charge. Note : The fixing of Galvalume roof sheet used as sun-shades & in walls at certain places in repair to be fixed by done of grooves cutting first, are inlcuding in the cost of item itself. No extra cost shall be paid for the same.

S & F Joist, channel, angle, or tee sections of Fe 410 -W (Gde E- 250) quality A, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated) complete all as specified & directed by Engineer-in-charge.

M&L 5cm Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for Granite 20mm thick table rubbed and polished in steps, jambs, pillars, window cills, cooking platform sand like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixure of pigment to match with marble shade of Makrana white complete all as specified and directed including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified & directed by Engineer-in-charge.

M&L for Glazed ceramic colour tiles in vertical surface 350x250mmx7mm/ 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4, complete all as specified and directed including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified & directed by Engineer-in-charge.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 complete all as specified & directed by Engineer-in-charge.

M & L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 complete all as specified & directed by Engineer-in-charge.

S & F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling alongwith 12mm thick Gypsum board in ceiling including dismantling of wall and ceiling boards (fibre, pulp, insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pedestal pattern including connecting to flush tank, ccomplete all as specified & directed by Engineer-in-charge.

S&F in repairs 10 ltrs capacity PVC low level flushing cistern with inlet, ball valve, float, handle including fitting and fixtures and taking down the old damaged cisterns and providing connections to WC and flush pipe without any damage to the existing fittings, complete all as all as directed.

S& F in repair, Vitreous china bowl urinal flat back, size of 465 x 355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern) including flush pipe and waste pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe).

Taking down chowkats or frames exc 1.5 sqm but not exceeding 4 sqm each without taking off shutters from the frames including iron mongry.

Taking down chowkats or frames n.exc 1.5 sqm each, without taking off shutters from the frames including iron mongry.

S&F butt hinges 75mm long stainless steel.

S&F Anodised aluminium alloy handles cast type, each 125mm long

S&F butt hinges 100mm long stainless steel.

S&F Anodised aluminium alloy handles cast type, each 150mm long

S&F Aluminium anodised, barrel tower bolts 125mm long of extruded section and fixed

S&F Aluminium anodised, barrel tower bolts 75mm long of extruded section and fixed

M&L for Anodised aluminium frame powder coated for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F Aluminium window and ventilator shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L for aluminium sliding track for Aluminium door/window glass shutter and cupboards, complete all as specified and directed by Engr-in-charge

S&F Slide roller for Aluminium door/windows shutter and cupboards, complete all as specified and directed by Engr-in-Charge

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engr-in- charge.

S & F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples in repairs

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane, all as specified and as directed.

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane, all as specified and as directed.

S & F Solar control film 25 micron reflective type exc 1.50 Sqm, sticked to glass panes as per instructions of manufacturers

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

S/F Solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube suppling and fixing in opening as per specification and drawing

S/F 30mm thick of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc all as specified and directed.

S&F in repairs of harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.

S&F in repairs tubular towel rail brass chromium plated 20mm dia D type 60cm long complete all as directed.

M&L 50 mm thick PCC 1:3:6, type C1 (using 20mm graded stone aggregate) in plinth protection and path laid in alternative bays finished even and smooth without using extra cement, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including raking out joints, hacking for key, scrubbing down with water etc

M&L for 10mm thick rendering in cement mortar 1:4 on fair face of stone masonry surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick on stone surfaces or other than fair faces of brick work or on one side of lathing in cement mortor 1:6, finished even and smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion over 3mm thick wall care putty, complete all as specified and directed.

M&L for prepration of new plastered wall surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of Plastic emulsion paint over a priming paints plaster coat , complete all as specified and directed.

M & L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F in repair, 1000 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in position with 20mm bore dia ball brass valves high pressure ,with polythene float and flynut screwed for iron pipe or brass ferrule, all as specified in SSR Part-I, complete including dismantling of existing tank with float valve.

S&F in repairs Gun Metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, 20mm bore complete all as directed.

S&F in repair, Vitreous china wash basin pedestal type, white, flat back, size 550 X 400 mm excluding taps, chain and plug and porcelain stopper but including CP waste coupling & brackets and fixed complete all as specified and directed.

S&F in repair Brass CP mixer of 15mm dia bore for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified & directed by Engr-in-charge.

S& F in repairs, White vitreous china laboratory sink of size 600x450x200mm laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, complete all as specified & directed by Engr-in-charge.

S&F Brass CP Florentine Pillar Cock with Extended Lever Handle elbow operated screwed down for iron pipe and fixed in repair, complete all as specified & directed. Make -Jaquar, code FLR-CHR-5031N or equivalent in CERA/PRAYAG.

S&F in repairs 15mm dia Bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as directed.

S&F in repairs 15mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as directed.

S&F in repair, PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed.

S&F 15mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc including taking down of old existing GI tubing, all as specified and as directed.

S&F 20mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc including taking down of old existing GI tubing, all as specified and as directed.

S&F in repair Soap dish, vitreous China white, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches in repair.

M & L for 150mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars including Demolition and breaking of 150mm dia up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

M & L Cement concrete type D2 (1:4:8) using 40mm graded aggregate as in foundations, filling and mass concrete

M & L Concrete bed type D2 (1:4:8) using 40mm graded aggregate to drain pipes of 150mm dia including packing under and completely surrounding pipes with concrete after they are laid and tested; in

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil all as specified & directed by Engineer-in-Charge.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and getting out in soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as directed.

Removing excavated soft/ disintegrated rock to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-Charge.

M&L Cement concrete type C1 (1:3:6) using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

S&F in repairs cast iron nahani trap with CP grating including jointing to waste pipe in cement mortar, diameter of out let 75mm bore fixed in cement concrete type B1 (1:2:4) complete all as directed.

M& L for Power Coated X Ray Lead double door with frame, size as per site requirement of High Quality, customized, of any colour used in X ray room, Radiation proof rooms manufactured in accordance with WIESPL technology. The doors are to be laminated with HPL in any color desired. Automated systems for both sliding and wide-open doors are to be provided by manufacturers. Doors are operated from wall board, elbow buttons or Infra Red. Doors will be equipped with door viewers, windows used for room observation, Xray shields made of 0.5-3 mm thick plates. Thickness of door wings range from 40 and 60 mm. NOTE :- (i) The doors to be installed/fixed by the original manufacturer's only. (ii) Submission of Lead door certificate from original manufacturer's is mandatory on completion of work.

M&L for Endura ceramic tiles exterior grade 300 x 300 x 10mm including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match all as specified & directed. Make : - Johnson/Orient Bell/Somany or equivalent as approved by GE.

CEMENTITIOUS ELASTOMERIC SLURRY COAT: M & L for water proofing treatment on roofs of slabs by complete removal/taking down of existing treatement, by applying acrylic based polymer modified cementitious elastomeric flexible composite coating system consisting of applying: First coat applying with CICO TAPECRETE-P151 or equivalent in FOSROC/STP/SIKA/BASF, mixed with neat fresh cement in the ratio of 1:1 by weight after dust free and moist the surface. Laying second layer of Fiber glass cloth of 45 GSM when the first layer is still green. Overlaps of joints of fiber cloth should not be less than 10 cm. Applying final layer of cementitious elastomeric flexible composite coating system. The whole terrace so finished shall be flooded with water for a minimum period of 24 hours for curing and for final test. “All above operations to be done in order by the manufacturer's authorised applicator only.

HIGH BUILD ELASTOMERIC LIQUID MAMBRANE (PU BASED): M & L For applying of polyurethane based tar extended seamless elastomeric protective coating system, conforming to ASTM C-836-03 and ASTM C 898-09 ideally suited for waterproofing of roof, walls and foundation MAKE: CICO CORCHEM 206I or equivalent in FOSROC/STP/SIKA/ BASF, following the single component solvent based polyurethane compound CORCHEM 2P or equivalent in FOSROC/STP/SIKA/BASF recommended to be used as a primer before application of CORCHEM.

M & L for providing and applying seamless thermal insulating elastomeric high build liquid membrane for concrete roofs, exterior wall and exposed surface. Make : CICO THERMOSEAL XL or equivalent in / FOSROC/ SIKA/STP Limited as approved with dual effects by reflecting more than 80% of sun rays thereby heating of roof surface reduces remarkably due to high amount of Titanium di oxide & transfer of heat from roof surface is blocked due presence of ceramic micro sphere with the application of roof and exterior side walls, it reduces energy cost approx 20%.

Note : For item Ser No 77 to 79 : -(i) The structural rehabilitation treatment shall be applied by the company’s authorized applicator only. (ii) Contractor have to get prior approval of applicator or authorized agency by submitting its authorization letter to this office for approval prior to commencement of work. (iii) Submission of 10 year warranty certificate for waterproofing treatment work over roof is mandatory after completion of work.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M&L Point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 1.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLS cable 1100 volts grade, ISI 694 marked with valid CML No. in and including medium grade, PVC concealed conduit MMS, ISI marked of dia not less than 20 mm and conduit accessories conceled in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- Note : Modular switch and socket shall be measured and paid separately.Make: Polycab/Havells

a) One light point controlled by one switch

b) One ceiling/exhaust fan point controlled by one switch

c) One wall mounted fan point controlled by one switch

(d) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(e) One 2/3 pin socket outlet 5Amps on independent board.

All as per item No 83.00 above but pint wiring with 4.00 sqmm single core multi stranded copper conductor PVC insulated and unsheathed (FRLS) cable 1100 volts grade and 4.00 Sqmm PVC insulated and unsheated (FRLS) cable 1100 volts grade with multi stranded copper conductor as earth wire for 15/16 Amps multi porpose socket combination point on independent board.Note : Modular switch and socket shall be measured and paid separately. Make :-Polycab/Havells .

S/F modular switch one way 6A, 1 module .Make : Havells crobtree

S/F modular socket 6A-2/3 pin combined 2 module.Make : Havells crobtree

S/F modular switch socket combined 6A/16A , 6 pin, 3 module.Make : Havells crobtree

S&F step type modular fan regulator 120W -2 module ISI Marked with valid CML No complete all as speified and as directed.Make : Havells crobtree

S/F Ceiling rose, three terminals PVC/polycorbonate, isolated body.Make : Havells crobtree

S& F finished mounting Modular Metal Flush/Sunken Box of suitable size of following Sizes:- Make:- Havells (Crabtree) /Legrand /Schnieder.

(a) 1 Module

(b) 2 Module

(c ) 3 Modules

(d) 4 Modules

(e) 6 Modules

(f) 8 Modules

(g) 12 Modules

S&F Modular white cover plate with frame innner and outer plates for following sizes:- Make: - Havells (Crabtree) /Legrand /Schnieder.

(a) 1 Module

(b) 2 Module

(c ) 3 Modules

(d) 4 Modules

(e) 6 Modules

(f) 8 Modules

(g) 12 Modules

S/F vertical DBs TPN 4 way 415 V double door powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 250 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required,suitable for TP/FP MCCB as incomer with MCCB 160A , and with SP/TP MCCB's as outgoing MCCB FP 160A , 25 KA .Make :Legrand/Havells/Indoasian

S & F for MCB DB SPN 12 way double door IP 43 complete prewired including 200 Amps rated Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .Make :Legrand/Havells/Indoasian

Supply and fixing 415V 10KA 'C" curve MCB's TPN 40 to 100 Amps four pole and current carrying capacity in the DB complete with connecting and comissioning complete all as specified & directed. Make :Legrand/Havells/Indoasian

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve.complete all as specified & directed. Make :Legrand/Havells/Indoasian

Supply and fixing MCB's single pole 10 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve.complete all as specified & directed. Make :Legrand/Havells/Indoasian

M & L for submain wiring with approved colour code/as per IS (Red,black & green for three phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 16.00 Sqmm (FRLS) in conduit including two run of PVC insulated multistranded copper conductor nominal cross sectinal area of 16.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Four runs of 16.00 Sqmm cable & one run of 16.00 Sqmm cable shall be paid as one unit length)

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase)concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 10.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 10.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Two runsof 10.00 Sqmm cable & one run of 10.00 Sqmm cable shall be paid as one unit length)

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase)concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm cable shall be paid as one unit length)

S&F in repair modular type Gyser/AC Box having 20 Amp MCB SP as incomer complete all as specified including taking down existing once complete .

Supply and fixing of building security light fitting LED 45 Watt IP 66 IK 07 pressure dia cast aluminium housing with high efficient LED as lihjting souce and PC cover having TOP opening sepreate drive compartment etc and connecting as specified and directed .Make Havells cat pot No .EDDURAPEARLNEOSL45WLED757PASYTOPC or Crompton/Philips equivalent as approved.

S& F in repair bracket of GI pipe medium grade of 40mm dia ,1.2 meter in length clamps made of FI 40 mm x 6mm incl nuts ,bolts & washers,painting complete as specified.

S & F surface and wall mounted LED tube light along with fixture ,4 ft ,22W ,extruded aluminium housing provided for efficient heat disspation with polycarbonate ,operating voltage 240 V ,50HZ ,AC supply and operating tempureture 0 to 50 C ,power factor >0.9 ,lumen output > 2000 and provision of new 3 core multistanded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipe completion all as specified and directed.

Supply and fixing of recessed mounted down lighter with extruded aluminium frame with high bright LED,idealy suited for low ceiling areas Brilliance 36watt LED 6K,ceiling cutout 2ft x 2ft with suitable lumen 2700/4300/6000k all as directed.Make : Orient/Havells/crompton

S & F in repair of LED tube light fitting 10 watt tube LED Neutral white in colour, 600 mm in length wall mounted LED batten,extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver,optic diffused type ENDURA LINER NEO including all electric connection with whilte flexible cord 1.50 Sqmm 3 core as required complete all as specified and directed.

S&F fans ceiling complete with electronic type regulator and accessories 230V,1200 mm sweep .Min air delivery 210 CFM with service value 6.00 BEE . 5 star rated with with brushless direct current motor (BLDC) necessary connecting cable recommended / provided by manufacturer complete.

S&F wall mounted fan AC single phase 230V of size 450mm sweep with blades and frame and louvers.Make Havells Model Name :Airboll Hi Speed or Almonard/Khaitan

S&F exhaust fan steel body AC single phase 230V of size 300 mm sweep with blades and frame and louvers

Cutting of wall with mason for making window suitable for fixing of 300 mm exhaust fan and making good as per existing surface of wall complete all as specified and directed .

Supply & fix water heater storage type (Geyser) vertical type ,inner container of capacity 50 ltrs, electrically operated ,AC 230 Volts ,including 10 Nos of fashner nuts required suitable size fixed in brick wall complete all as specified and directed .BEE 5 star rated.

M & L for PVC connection pipe (copper) chromium plated 8 mm dia both end threaded incl brass coupling bolt cone washer complete , length of pipe is not less than 450 mm suitable for Hot/ cold water system complete as all specified and directed.

S & F for Bib cock 15 mm dia cast copper alloy with butter fly handle, screwed down, screwed one ends for pipe of 15 mm dia complete all as specified and directed.

S & F for Stop valve 15 mm dia cast copper alloy with butter fly handle, screwed down, screwed both ends for pipe of 15 mm dia complete all as specified and directed.

S & F for GI tubing 15 mm dia medium grade galvanised laid in wall ceiling & Floor including all fittings all as specified and directed.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground levl connected to galvanized iron strip 32x6 mm as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed.

M& L Earthing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and scewed including 3 nos 8 mm dia 25 mm long hex head screw.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium condutor of size 50 sq mm 3.5 Core complete all as specified and directed by Engineer-in-charge.

M&L for sand cushioning to underground PVC/XLPE cable with tibba sand and punning to provide required cover complete all as directed by Engineer-in-charge. (Note :- For the purpose of payment only punned thickness will be measured).

Supply & laying 40 to 50 mm thick roughly hammer dressed Jodhpur stone patti cable cover 25 cm to 30cm wide and n.exc 60 cm long each laid dry abutting with each other with maximum gap between adjustment slabs n. exc 10 mm complete all as specifeid & directed by Enginner-in-charge.

S&F steel water tubing (ISI marked) medium grade galvanised, 80mm bore with fittings (ISI Marked) laid in trenches, jointed and tested complete all as specified and directed by Engineer-in-charge.

M&L for road cutting for passing of LT cable inside GI pipe of suitable size complete digging after laying of pipe line / cable making good the surface complete all as specified and directed by Enginner-in-charge .

S&F Gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, 20mm bore complete all as specified & directed by Engineer-in-charge.

M & L for cutting existing GI tubing for alteration or additions of sizes including screwing existing GI tubing for tapping & making new connections etc of 20mm bore sizes complete all as specified & directed by Engr-in-Charge.

M/S VISHNOI ENTERPRISES

S K TRADER