Repair work in Ordnance Club at OFCd Estate

M & L for rough excavation not exceeding 1.5 m deep and getting out in soft soil.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L Brushing neat cement slurry with 3.0kg of cement per sq. metre®and Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes (1:4).

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match colored tiles.( make: kajaria, jonson, somani) Shade / design as approved by EIC at the time of execution.

S&FVirified Ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes.conforming to I. S.1161- 1979 grade St.-240

Dismantling boarding, any description, fixed in any position with nails.

S & F of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to tre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&f for Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) thickness 8mm.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash asteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F 4.8mm thick Sheet glass, ordinary quality, glazing with oil putty in square exc 0.5 sq. m in each pane sheet Extra over sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted, on one side

M&L for Preparation of new surface of any descriptionin width or girth not otherwise described and apply one coat of red oxide zinc chrome primer and two coat of synthetic enamel paint. Shade will be decided by EIC.(steel surface).

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L rendering 15mm thick on fair faces of brick work or concrete surfaces1:6 cement plaster and rendering is to be finished even and smooth (without using extra lime or cement)®

M&L for 3mm thick wall care putty on wall (Make: asian, JK,Birla)

Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3.

Removing building materials etc. to a distance of 5 km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination.(0.62 cum =One load)

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 15 mm dia

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc, Brushing neat cement slurry with 3.0kg of cement per sq. metre®screed bed (1:4) of avg.25 mm thick over cemented surface and the surface to be finished even & smooth without using extra cement & maintaining proper cross slope for effective drainage.

M&L for painting with aluminium paint of approved brand and manufacture to give an even shade two or more coats on new work.