Construction of Vending Market at Durwa Bazar Tand Ward No 5 at Latehar Under Nagar Panchayat Latehar

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design,building specification & direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume) Sand filling in Foundation, Flooring and Below Tai Beam

Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I

Providing And Fixing in position cement concrete of specified grade excluding the coast of centering and shuttring -All work up to plinth level 1:11/2:3 (1 cement :11/2 coarse sand(Zone-III):3 graded stone aggregate 20mm nominal size)

Providing And Fixing in position cement concrete of specified grade excluding the coast of centering and shuttring -All work up to plinth level .1:11/2:3(1 cement :11/2 coarse sand(Zone-III):3 graded stone aggregate 20mm nominal size) 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:11/2:3 (1 cement :11/2 coarse sand (Zone-III):3 graded stone aggregate 20mm nominal size)

Centering and shuttring including,propping etc and removal of from for Foundation, footings below bases of coluumn etc for mass concrete.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:11/2:3 (1 cement :11/2 coarse sand (Zone-III):3 graded stone aggregate 20mm nominal size)

Centering and shuttring including,propping etc and removal of from for Column,Pillars, Piers, Abutments,Posts and Struts

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

Centering and shuttring including,propping etc and removal of from for Column,Pillars, Piers, Abutments,Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:11/2:3 (1 cement :11/2 coarse sand (Zone-III):3 graded stone aggregate 20mm nominal size)

Centering and shuttring including,propping etc and removal of from for lintel, beams, plinth beam, girders, bressumers and cantilevers

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttring including,propping etc and removal of from for lintel, beams, plinth beam, girders, bressumers and cantilevers

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttring including, propping etc and removal of from for Suspended floors, roofs, landigs, balconyes and acess platform

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttring including,propping etc and removal of from for Suspended floors, roofs, landigs, balconyes and acess platform, chajja

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttring including,propping etc and removal of from for lintels, beams, plinth beams girder etc.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttring including,propping etc and removal of from for Stairs, (excluding landings) excepts spiral staircases

Providing tor steel reinforcement rods as per approved design --do-- tht fe 500(only valid for tata(tiscon),sail, jspl,electeo steel, ltd.bokaro and vizag (RINL) TMTC-500 8mm dia

TMTC-500 10mm dia

TMTC-500 12mm dia

TMTC Fe-500 16mm dia

TMTC Fe-500 20mm,25mm, dia

Water proofing for old and new roof slab:- providing and laying water proofing treatment on roof slab by appling two component,factory designed ready to use acrylic modified flexible materials applied with …

Covering of treated surface with pcc:- providing 50 mm thick cement concrete m20 maintaing slope in alternate 2mtx2mt panels with….

4211C, Dr. fixit pidiproof LW+ or equivalent providing and mixing liquid integral watwr proofing compound of concrete or plaster……

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mmdia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.

Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 125mm thick reinforced designation 75A brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I

Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. With float glass panes of 5.5 mm thickness

Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 20 guage G.C.I, sheet gate fitted on M.S. Angle frame of size 60x60x6mm. including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws win rubber stopper

Providing and laying doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying 25mm thick white makrana marble stone slab flooring of approved quality over 19mm. thick base of lime mortar (1:1:1) ( Lime putty : surkhi: coarse sand ) laid and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick white makrana marble tiles in risers of step, skirting and pillars of approved quality over 12mm thick base of cement mortar (1 :3) and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotta stone slab flooring of approved size texture and colour over 19mm tick base of lime with grey cement slurry mixed with pigment to granlithic fininsh with approved quality of carborandum stone including coast of curing taxex and royalty all complete...... ( iv)600x600mm

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Water proofrng for Old and New Roof Slab :- Providing and laying water prooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,\fbrush, roller or spray eppled wate r proof i n g coati n g as per man ufactl rer specificatio r-(With following steps :- (a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete. (b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured." (c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, _s reatiy to-use, flexible ce rnentttious material right angle to the '1st coat over the glass fibre laicl surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will berneasurecl." Alte r three days of drying the 2nd coal , the pat( td) + rryatei' ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal<age from soffit and if found necessary rectification lo be rjone as pcr satrsLction ol E/-ft,. protected from damage before screed over it. Watqrproofing Brand:* Sil<a Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A. Acrylic copol;,mer, Part 13 Specially graded cementitious powder - Density 1.6 l.rg/l (mixcd density) at +27oC Tensile Strength - 2 lllmm2 after 28 clays (with Fibre cloth) (According to ASTM D 2370) Prillcut Bond Streric;tl-r '-2 I'J/mm2 (concrete lajlqry) (Aqgcrdlglq ISO

covering of treated surface with p.c.c providing 50mm thick cement concrete m20 maintaining slope in alternative 2mtx2mt panels with appproved quality of stone chips of 20mm yp 6mm size graded and cleaned sand of fm2.5 to 3 including screaning shuttring ...........

providing and mixing liquid integeral water proffing compound in concrete or plaster as/per manufacture specifications and as per direction of engg in charge brand siska,plastocrateplus,mykproof wp10,fosroc conplastX4211C dr fixit pidiproof lw+or equivelent

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing & fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. Single socketed pipes. 110mm dia

Providing & fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion Bend -110 mm

Shoe - 110mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plgs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Carriage Of Materials Sand

Aggregate

Brick

ELECTRICAL WORK Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed with 2 mm thick PVC conduit, with modular type switch, modular plate, suitable size of GI box & earthing the point with 1.5 Sq.mm FR PVC insulated opper conductor single core cable etc as required.

Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box & earthing the point with 1.5 Sq.mm FR PVC insulated opper conductor single core cable etc as required.

Power plug wiring in PVC conduit (2x4 sq.mm.):- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

Supply & fixing 20A SPN MCB Industrial Socket Outlet: Supply and fixing of 25A, 240V, SPN insustrial type socket outlet with 2 poles and earth, metal enclosed plug top along with 25 amps 'C' series, SP MCCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket out let and complete with connections, testing and commissioning etc as required. (For split / window AC points).

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. 2x1.5 Sqmm + 1x1.5 sqmm earth wire (for Single Separate 6A) (Circuit shall be taken from nearest switch board)

2x2.5 Sqmm + 1x2.5 sq mm earth wire (for switch board circuit and 3 Nos. 6A sockets for LAN).

2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire.(for 20A SP Industrial Scoket)

S/F Modular blanking plate:- Supplying and fixing of the existing modular plate and switch box excluding modular plate etc, as required.

S/F SP MCB DB: S/F the following way single pole and neutral sheet M.C.B. Distribution board 240 V, on surface/recess,complete with tinned copper busbar, neutral busbar, earth bar, din bar, datachable gland plate, inter connections, phosphatized and powder painted including earthing etc as required (but without MCB/RCCB/Insolator)

S/F TP MCB DB: Supplying and fixing following way, three pole and neutral sheet MCB distribution board, 415 volts on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). 4 Way (4+12), Double Door (Horizontal Type).

8 way ( 4 + 24) Double door, Horizontal type

S/F 'C' series MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. 6/32A Single Pole

40 amps TPN

50/63 amps TPN

S/F Modular type electronic fan regulator: Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.

ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC exhaust fan upto 450 mm. sweep:- Installation of exhaust fan upto 450 mm in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Fixing louvers / shutters for exhaust fan:- Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

S/F PVC Conduit: Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for Tele, RJ45 Cat 6 data outlet for computer network. 25 mm

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. Telephone socket outlet

5/6 amps one way switch (500x3=1500)

5/6 amps 3 pin socket out let (500x3=1500)

S/F Modular boxes, base & cover plate:- Supplying and Fixing following size / modules G.I. box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 modules (78mm x 78 mm x 45 mm) (For Voice + Data Outlets)

8/9 Module (78mm x 230mm x 60mm)

Providing of PVC/XLPE insulated sheathed heavy duty, armoured electrical cable with aluminium conductor for working voltage up to and including 1110 Volts (Confirming to IS:- 1554 part-1) .Make- Havells/ Finolex/ Polycab. 3.5 Core 25 Sq.mm 1.1kV XLPE Al. Ar.Cable

3.5 Core 70 Sq.mm 1.1kV XLPE Al. Ar.Cable

3.5 Core 95 Sq.mm 1.1kV XLPE Al. Ar.Cable

CHEMICAL EARTHING FOR BUILDINGS AND ALL ELECTRICAL EQUIPMENTS:- Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure 300mm X 300 mm with C.I. cover plate having locking arrangement as earth chamber.The above chemical earthing includes the following items :- Supply of Pollution free Earthcon Compound 25Kg (or 2 bags of 12.5 Kg each) Supply of 17mm dia,250 micron,molecularly bounded copper coated 2 Mtr long electrode.

Supply 9/18W led (essential) in existing batten/angle holder. (Make :- Philips / Bajaj /Wipro).

Supply of surface mounted round circular ceiling light fixture with white epoxy powder coated CRCA housing with opel acrylic cover with 2X18W 'D' type led complete in all respect as required and as per the standard cataloge item. (Make- Bajaj BCSC 218 CFL W2EB / Philips / Wipro-FWP 41218.)

Building outer Light :- Supply fitting fixing and commissiong the building outer lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum Housing, toughened glass cover, efficient POT optics (IP66), ingressprotection, and special PUL coating for improved aesthetics with reflector and heat resistant toughened, pot optics reflector with acrylic blow cover, including 5ft long 50mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per installation drawing prescribed (IP-66) (Make:-Philips SGP438 1xSONT150W Lamp,Bajaj BGEST 150SVDD Complete IP66 FG HPSV- T-150W Lamp,Wipro -WST50150)

FANS & EXHAUST FANS Supply of AC 230/250 Volts, 50Hz, 300mm sweep/900 rpm Exhaust Heavy Duty Fans (Double Ball) including providing nuts- bolts, mounting frame and other required accessories etc. Make- Havells-Turbo Force / Bajaj-70069 / Crompton Greaves EXHD300-4-1 Before Procurement of light fittings & fans approval of the same has to be taken from E/I or Consultant.

Plumbing & Sanitary work Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) With "P" trap (a)12.5 lit. low level P.V.C. cistern

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I. (b) 580 mm long with 12.5 litre low level PVC cistern

Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware urinal of Hindustan "Parry" or any other approved ISS make with 5 ltrs. Capacity C.I. automatic fushing cistern of reliance for any other ISS approved make with all fittings with C.I. or RS brackets standard size G.I. flush pipe with fitting clamps 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 gms. 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per speciifcification and direction of E/I. Flat back or standing corner (600X350mm)

supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.

Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I. 20mm dia.

25mm dia.

Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. a) 15mm dia.

Making holes in walls for PVC Pipe and restoring the same atfer pipe Laying (b) 250mm thick wall

Cutting drain width wise above GL for laying PVC pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in C.M. (1:4) with neat cement punning as per specifciation and direction of E/I. (PVC 110mm dia)

Making holes in wall for laying PVC pipes and restoring the same all cost complete (PVC pipe 125mm dia)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 30% for labour and Contractors profit) Pillar cock (long neck) (Basic rate Rs.756.60 + 10% for C.P. & laying charge)

Bib cock - long thread (Basic rate Rs.701.10 + 10% for C.P. & laying charge)

Angular stop cock L.T.(Basic rate Rs.572.85 + 10% for C.P. & laying charge)

Glass shelf (Basic rate Rs.641.25 + 10% for C.P. & laying charge

Flush valve complete with 32mm size control cock & flange (Basic rate Rs.3283.20 + 10% for C.P. & laying charge

32mm dia. PVC waste pipe 750mm long with cushion (Basic rate Rs.52.00 + 10% for C.P. & laying charge

15mm C.P. nipple with coupling(As per JSR 14 basic rate Rs.72.70 + 10% C.P. & laying charge)

Steel jali - 100mm dia. (Basic rate Rs.40.20 + 10% for C.P. & laying charge

Providing Solvent cement (as per JSR 14 basic item - 140 + 10% C.P & laying charge

Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600 X 450mm

Supplying, fitting and fixing C.P. brass towel rail 20mm X 600mm with bracket container

Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge

Supplying, materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS 8931, 15mm dia nominal bore of approved brand C.P. fittings

Providing and fixing PTMT extension nipple 15mm size with 12" BSP thread 70mm length and 30mm breadth and weighing not less than 32gms of approved make

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc. 20mm nominal bore

25mm nominal bore

32mm nominal bore

Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110x110x110 mm

Bend 87.5 degree 110mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I. PVC cowl - 100mm dia.

Floor trap - 100mm dia.

Ring rubber

Door piece

Add GST 12% (Item No. 1 to 121)

Add Sub Tax 1% (Item No. 1 to 122)

NIRANJAN RAI