Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹44.9 LAccepted-AOC | ₹44.9 L Quoted ₹45.6 L | L1 | Accepted-AOC Lowest Bidder |
| 2 | L2₹47.5 LRejected-Finance SUKANTAPALLI LOWER BAGDOGRA PO BAGDOGRA DISTRICT DARJEELING WEST BENGAL PIN 734014 | BAGDOGRA | DARJEELING | WEST BENGAL | 734014 | ₹47.5 L | L2 | Rejected-Finance Not Lowest Bidder |
| 3 | L3₹49.8 LRejected-Finance | ₹49.8 L | L3 | Rejected-Finance Not Lowest Bidder |
| 4 | L4₹50.9 LRejected-Finance | ₹50.9 L | L4 | Rejected-Finance Not Lowest Bidder |
| 5 | L5₹51.0 LRejected-Finance | ₹51.0 L | L5 | Rejected-Finance Not Lowest Bidder |
| Sl No | Description | Qty | Unit | M/S GURUNG CONSTRUCTION L2 | PRADIP KUMAR BOSE L4 | UNIVERSAL CONSTRUCTION L6 | GOUTAM KUMAR GHOSH L1 | M/S K M CONSTRUCTION L3 | M/S KAR CONSTRUCTION L5 | NABIN CONSTRUCTION AND CO. L7 | NAYAK BROTHERS L8 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | M&L for identifying and rectifying day to day complaints of ceiling fan / exhaust fan / wall fan / cabin fan / pedstral fan or any type and any size fans at site on daily including taking down celiing fan / exhaust fan / Wall fan of any type / make / sweep from its location at OTM & Md accn under GE Bengdubi area, servicing of fans after removing blades, opening of fan at site and cleaning ball bearing, gun metal bush, filling grease /oil and changing of nut , screwes, check nuts, rubber reel, nut & bolts of size 15 mm to 60 mm including replacing defective condensor, ball bearing, conecting wire, gun metal bush,lock nuts, cross pin, ceiling rose etc if required and re-assembling of fan, blades, down rod, conopy etc and hanging back fan to its original location after cleaning of body, connecting to ceiling rose complete all as specified and directed.
Note : (i) all spare i.e condenser, ball bearing, flexible wire, bush shall be measured and paid under relevent item.
(ii) Cost of petty stores such as grease, lubricating oil, varnish, coil tie, lock nut , cross pin,check nuts,rubber seal etc are deemed to be included in quated rate.
(iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate.
(iv) Only replacement of fan capacitor will not be measured in the same item without taking down of fan. | 1,350 | Each job | 135 ₹1.8 L | 143 ₹1.9 L | 138 ₹1.9 L | 130 ₹1.8 L | 140 ₹1.9 L | 125 ₹1.7 L | 127 ₹1.7 L | 155 ₹2.1 L |
| 2.00 | Taking down carefully ceiling fan any sweep size and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades to the work shop for rewinding including cleaning and dismantling the fan into parts and segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan, testing and refixing the fan in same position including all electrical connection and material and labour for replacement of two nos split pins, one connection block and one rubber reel all as specified and as directed.
Note : (i) Rewinding work of armature shall be measured and paid separately.
(ii) New spare parts required for replacing old burn out parts shall be measured and paid separately.
(iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate. | 980 | Each job | 185 ₹1.8 L | 210 ₹2.1 L | 230 ₹2.3 L | 175 ₹1.7 L | 190 ₹1.9 L | 200 ₹2.0 L | 245 ₹2.4 L | 250 ₹2.5 L |
| 3.00 | Material and labour for removing burnt copper winding of ceiling fans 1200 mm sweep including necessary dismantling, cutting and removing of unsv windings, cleaning, segregation of serviceable and unsv parts including re-windings of complete fan winding with super enameled copper wire of existing gauge and weight of approved make and brand and taping, quick heat varnishing, baking, drying in heat chamber to obtain proper insulating resistance and reassembling the fans including replacement of other unsv parts and testing complete all as specified and as directed. | 910 | Each job | 695 ₹6.3 L | 738 ₹6.7 L | 800 ₹7.3 L | 700 ₹6.4 L | 750 ₹6.8 L | 710 ₹6.5 L | 725 ₹6.6 L | 730 ₹6.6 L |
| 4.00 | All as pr item No. 03.00 above but for 1400 mm sweep ceiling fan all as specified and as directed. | 90 | Each job | 1,125 ₹1.0 L | 1,075 ₹96,750 | 1,100 ₹99,000 | 1,050 ₹94,500 | 1,200 ₹1.1 L | 1,320 ₹1.2 L | 1,340 ₹1.2 L | 1,378 ₹1.2 L |
| 5.00 | Taking down carefully Exhaust fan any sweep size and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades to the work shop for rewinding including cleaning and dismantling the fan into parts and segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan, testing and refixing the fan in same position including all electrical connection and material and labour for replacement of two nos split pins, one connection block and one rubber reel all as specified and as directed.
Note : (i) Rewinding work of armature shall be measured and paid separately.
(ii) New spare parts required for replacing old burn out parts shall be measured and paid separately.
(iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate. | 310 | Each job | 190 ₹58,900 | 210 ₹65,100 | 160 ₹49,600 | 175 ₹54,250 | 180 ₹55,800 | 170 ₹52,700 | 180 ₹55,800 | 200 ₹62,000 |
| 6.00 | Material and labour for removing burnt copper winding of Exhaust fans upto 300 mm sweep including necessary dismantling, cutting and removing of unsv windings, cleaning, segregation of serviceable and unsv parts including re-windings of complete fan winding with super enameled copper wire of existing gauge and weight of approved make and brand and taping, quick heat varnishing, baking, drying in heat chamber to obtain proper insulating resistance and reassembling the fans including replacement of other unsv parts and testing complete all as specified and directed. | 230 | Each job | 775 ₹1.8 L | 700 ₹1.6 L | 758 ₹1.7 L | 750 ₹1.7 L | 790 ₹1.8 L | 800 ₹1.8 L | 900 ₹2.1 L | 925 ₹2.1 L |
| 7.00 | All as pr item No.06.00 above but for above 300 mm sweep and upto 450 mm sweep Exhaust fan all as specified and as directed. | 80 | Each job | 1,275 ₹1.0 L | 1,265 ₹1.0 L | 1,300 ₹1.0 L | 1,250 ₹1 L | 1,350 ₹1.1 L | 1,380 ₹1.1 L | 1,400 ₹1.1 L | 1,100 ₹88,000 |
| 8.00 | Taking down carefully Wall mounting Fan any sweep size and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades to the work shop for Rewinding including cleaning and dismantling the fan into parts and segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan , testing and refixing the fan in same position including all electrical connection and material and labour for replacement of two nos split pins, one connection block and one rubber reel all as specified and as directed.
Note: (i) Rewinding work of armature shall be measured and paid separately.
(ii) New spare parts required for replacing old burn out parts shall be measured and paid separately.
(iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate. | 35 | Each job | 130 ₹4,550 | 160 ₹5,600 | 140 ₹4,900 | 132 ₹4,620 | 144 ₹5,040 | 170 ₹5,950 | 200 ₹7,000 | 255 ₹8,925 |
| 9.00 | Material and labour for taking out and removing burnt copper winding of wall mounting fan of any sweep size, cleaning the armature, rewinding the fan armature for wall fan of any size with new super enamelled copper wire of existing gauge including supply and fixing necessary insulating materials etc and varnishing with approved grade of insulation varnish and heating up and testing all as specified and as directed. | 35 | Each job | 730 ₹25,550 | 744 ₹26,040 | 740 ₹25,900 | 725 ₹25,375 | 780 ₹27,300 | 800 ₹28,000 | 850 ₹29,750 | 900 ₹31,500 |
| 10.00 | Supply only bearing No. 6201/6202 for ceiling / Exhaust fan.
(Make - TATA/SKF/NBC/HCH ). | 2,540 | Each | 120 ₹3.0 L | 200 ₹5.1 L | 146 ₹3.7 L | 125 ₹3.2 L | 135 ₹3.4 L | 140 ₹3.6 L | 156 ₹4.0 L | 167 ₹4.2 L |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
8 Jan 2026, 6:00 pmClosed
GARRISON ENGINEER
Bengdubi Military Station PO-Bengdubi, Dist-Darjeeling, Pin 734424
REPAIR MAINTENANCE OF CEILING FAN EXHAUST FAN WALL FAN FOR OTM MD ACCN AND OLD UNSV ALLUMINIUM INTERNAL WIRING WITH ALL FITTING AND FIXTURE SWITCH SOCKET ETC AT VARIOUS UNITS UNDER AGE EM OF GE BENGDUBI
2025_MES_745180_1
8764/E8
Open Tender
Civil Works
180 days
GARRISON ENGINEER BENGDUBI
Please refer NIT
7 documents required · 7 mandatory
₹500
GARRISON ENGINEER
₹90,000
Yes
7 Feb 2026
18 Dec 2025
10 Jan 2026
18 Dec 2025
8 Jan 2026
1 Jan 2026
19 Dec 2025 - 25 Dec 2025
Amount
Material and labour for removing burnt copper winding of ceiling fans 1200 mm sweep including necessary dismantling, cutting and removing of unsv windings, cleaning, segregation of serviceable and unsv parts including re-windings of complete fan winding with super enameled copper wire of existing gauge and weight of approved make and brand and taping, quick heat varnishing, baking, drying in heat chamber to obtain proper insulating resistance and reassembling the fans including replacement of other unsv parts and testing complete all as specified and as directed.
All as pr item No. 03.00 above but for 1400 mm sweep ceiling fan all as specified and as directed.
Material and labour for removing burnt copper winding of Exhaust fans upto 300 mm sweep including necessary dismantling, cutting and removing of unsv windings, cleaning, segregation of serviceable and unsv parts including re-windings of complete fan winding with super enameled copper wire of existing gauge and weight of approved make and brand and taping, quick heat varnishing, baking, drying in heat chamber to obtain proper insulating resistance and reassembling the fans including replacement of other unsv parts and testing complete all as specified and directed.
All as pr item No.06.00 above but for above 300 mm sweep and upto 450 mm sweep Exhaust fan all as specified and as directed.
Material and labour for taking out and removing burnt copper winding of wall mounting fan of any sweep size, cleaning the armature, rewinding the fan armature for wall fan of any size with new super enamelled copper wire of existing gauge including supply and fixing necessary insulating materials etc and varnishing with approved grade of insulation varnish and heating up and testing all as specified and as directed.
Supply only bearing No. 6201/6202 for ceiling / Exhaust fan. (Make - TATA/SKF/NBC/HCH ).
Supply only bearing No.6203/6204 for ceiling / Exhaust fan. (Make - TATA/SKF/NBC/HCH ).
Supply only gun metal bush of any size for ceiling / Exhaust fan/ wall mounting fan . (Make - TATA/SKF/NBC/HCH ).
Supply only fan condensor 3.15 mfd oil filled. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply only fan condensor 3.15 mfd dry type. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply only fan condensor 2.5 mfd oil filled. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply only fan condensor 2.5 mfd dry type. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply only Exhaust fan condensor 1.5 mfd dry type. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply only mounting clamp assembly complete for ceiling fan 1200mm/1400mm sweep brass type with amp,bolt,nut,washers, safety/ split pins and rubber bush and all as specified and as directed.
Supply only down rod complete suitable for any type any size of ceiling fan complete all as specified and as directed.
Supply only PVC flexible multi stranded copper wire twin twisted two core of size 0.75 sqmm all as specified and as directed. (Make:Havells/Plaza/Polycab/KEI)
Supply and fixing in repair fan condensor 2.5 mfd oil filled 240 volts for rectification of day to day fan not working complaint at site. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply and fixing in repair fan condensor 2.5 mfd dry filled 240 volts for rectification of day to day fan not working complaint at site. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply and fixing in repair fan condensor 3.15 mfd dry type 240 volts for rectification of day to day fan not working complaint at site. (Make - USHA/UNIVERSAL/Havells/Tibcon).
Supply and fixing in replacement sheet metal louvers shutters for Exhaust fan of any size upto 300 mm sweep suitable for any make made of GI sheet and fixing with fasteners etc complete all as specified and as directed.
Supply and fixing in replacement sheet metal louvers shutters for Exhaust fan of any size above 300 mm sweep suitable for any make made of GI sheet and fixing with fasteners etc complete all as specified and as directed.
S & F for in repair energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make: Usha/Bajaj/Havells
S & F for in repair energy efficient exhaust fan of 380 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make: Usha/Bajaj/Havells
S & F for in repair energy efficient exhaust fan of 230 mm sweep made of sturdy Engineering Plastic Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make: Usha/Bajaj/Havells
Supply and fixing in repair Wall fans complete with blades, electronic regulator and accessories, 230V,400 mm sweep. Five star rated complete all as specified and directed. Make: Bajaj/Havells/Usha
Material and labour for painting of ceiling fans complete of any sweep size and any make with one coat of first quality synthetic enamell paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavaties with filler materials,and writing serial / MES number as specified (with paint of black colour with each letters/figures in Block of height n.exc 2 cm) complete all as specified and as directed.
All as per item no-30.00 above but for painting of exhaust fans of any sweep size with blade complete of any sweep/make all as specified and as directed.
Supply and fixing in repair aluminium based ceiling fan blade (set of 3 blade) suitable for 1200/1400 mm sweep ceiling fan with nut bolt complete all as specified and directed. Make: as per approved by GE.
Supply and fixing in repair metal exhaust fan blade (three blade set) of any sweep size exhaust fan with nut, bolts complete all as specified and directed. Make:as per approved by GE.
Supply and fixing in repair ceiling fan canopy as per existing size (set of 2 nos. upper/lower). Make :as per approved by GE.
Supply and fixing in repair ceiling fan hook made of Mild steel flat iron 4 mm thick of suitable size and any type as per existing position with suitable size nuts, bolts and washer as required for hanging ceiling fan safely complete all as specified and as directed.
Supply and fixing in replacement Exhaust fan Frame metal type of size upto 300 mm sweep as per existing shaft size suitable for any make including bolts,nuts and washer etc as required complete including taking down old unserviceable one all as directed.
Supply and fixing in replacement Exhaust fan Frame metal type of size above 300 mm and upto 450 mm sweep as per existing shaft size suitable for any make including bolts,nuts and washer etc as required complete all specified and directed.
Taking down carefully copper / aluminium point wiring (light, fan, switch,socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose,sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.
Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.
Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls directed.
Material and labour for point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor drawn through and incuding medium grade PVC conduit 20mm size with all accessories such as elbow, tee, bend etc, ISI marked, concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including or modular metal flush box for fixing modular switch, socket etc and mild steel sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly and coated of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one way switch complete all as specified and directed. Note :- Switches, socket and fan regulators and modular box inner and outer cover plate to be measured and paid separately.
All as per item no 41.00 above but one bell point controlled by one bell Push
All as per item no 41.00 above but one 5 Amps socket out let point controlled by one switch on same board with other switches.
All as per item no 41.00 above but one 5 Amps socket out let point on independent board controlled by one switch.
All as per item no 41.00 above but one light point controlled by one, two way switch 5 Amps
All as per item No 41.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board.
Material and labour for point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor drawn through and non metallic rigid PVC casing caping 20mm double lock system with all accessories such as elbow, tee, bend etc, ISI marked on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly and coated of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one way switch complete all as specified and directed. Note :- Switches, socket and fan regulators to be measured and paid separately.
All as per item no 47.00 above but one bell point controlled by one bell Push
All as per item no 47.00 above but one 5 Amps socket out let point controlled by one switch on same board with other switches.
All as per item no 47.00 above but one 5 Amps socket out let point on independent board controlled by one switch.
All as per item No 47.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board.
Material and labour for point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor drawn through in existing conduit on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly and coated of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one way switch complete all as specified and directed. Note :- Switches, socket and fan regulators to be measured and paid separately.
All as per item no 52.00 above but one bell point controlled by one bell Push
All as per item no 52.00 above but one 5 Amps socket out let point on independent board controlled by one switch.
All as per item No 52.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board.
Supply and fixing switch piano flush button single pole one way 5 amps, AC 240 Volts complete all as specified and directed.
Supply and fixing in repair switch piano flush button single pole one way 5 amps, AC 240 Volts complete all as specified and directed.
Supply and fixing socket outlet flush type 5 Amps, 5 pin, AC 240 Volts complete all as specified and directed.
Supply and fixing in repair socket outlet flush type 5 Amps, 5 pin, AC 240 Volts complete all as specified and directed.
Supply and fixing switch piano flush button single pole one way 15 Amps AC 240 volt complete all as specified and directed.
Supply and fixing in repair switch piano flush button single pole one way 15 Amps AC 240 volt complete all as specified and directed.
Supply and fixing socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amps, AC 240 volts complete all as specified and directed.
Supply and fixing in repair socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amps, AC 240 volts complete all as specified and directed.
Supply and fixing bell push single pole, 6 Amps, AC 240 Volts, flush type complete all as specified and directed.
Supply and fixing in repair bell push single pole, 6 Amps, AC 240 Volts, flush type complete all as specified and directed.
S&F in replacement Lamp holder, PVC / Polycarbonate type with back plate suitable for B22 lamp complete all as specified and directed.
Supply and fixing celing rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.
Supply and fixing in repair celing rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.
Supply and fixing electronic Fan regulator 450 watt 2 module, with 5 step type regulator complete all as specified and directed.
Supply and fixing in repair for electronic Fan regulator 450 watt 2 module, with 5 step type regulator complete all as specified and directed.
Supply and fixing ding dong Bell, AC 240 Volts,single pole complete all as specified and directed.
Supply and fixing Bell multi music type AC 240 Volts, single pole complete all as specified and directed.
Refixing paino switch of any capacity 5 /15 amps obtained from item no 38.00 complete all as specified and directed.
Refixing socket 5 amps or 15 amps capcaity obtained from item no 38.00 complete all as specified and directed.
Supply and fixing white finished single mounting one modular inner plate & outer top cover plate suitable for housing modular accessories with one module metal flush box complete all as specified and directed.
All as per item no 75.00 above but suitable for 2 modules
All as per item no 75.00 above but suitable for 3 modules
All as per item no 75.00 above but suitable for 4 modules
All as per item no 75.00 above but suitable for 6 modules
All as per item no 75.00 above but suitable for 8 modules
Supply and fixing modular Switch 10 Amps single pole, one way complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing Modular Socket outlet, multi purpose, 5 Pin 10 Amps flush type complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing Modular Bell push flush type,10 Amps fixed complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing Modular Socket outlet, multi purpose, 6 pin 16 Amps universal socket complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing Modular Switch 16 Amps single pole, one way complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing modular fan regulator 150 Watt of four step type complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing Modular Socket outlet 3 pin 25 Amps two module AC 230 volts complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing Modular starter Switch 25 Amps two module AC 230 volts complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.
Supply and fixing in repair PVC rectangular block for mounting switches, sockets ,fan regulator etc with 3 mm thick plastic laminated sheet cover of size 350 x 300 x 50 mm complete all as specified and directed.
All as per item no 89.00 above but of size 250 x 200 x 50 mm.
All as per item no 89.00 above but of size 200 x 150 x 50 mm.
All as per item no 89.00 above but of size 175 x 100 x 50 mm.
All as per item no 89.00 above but of size100 x 100 x 50 mm size.
Supply and fixing in repair pressed steel terminal rectangular sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly for mounting, switches, sockets, fan regulator etc including 3.00 mm thick plastic laminated sheet cover of suitable size for MS box size of 250 x 300 x 50 mm with brass screws and brass washers complete all as specified and directed.
All as per item no 94.00 above but of MS box size of 200mm X 250 mm
All as per item no 94.00 above but of MS box size of 200mm X 150 mm
All as per item no 94.00 above but of MS box size of150mm X 100 mm
All as per item no 94.00 above but of MS box size of 100mm X 100 mm
Supply and fixing in repair plastic laminated bakelite sheet cover of Hylam brand 3.00 mm thick including cutting holes for switches, sockets etc as per requirement including fixing with brass machine screws and washer for size 275 mm X 325 mm complete all as specifed and directed.
All as per item no 99.00 above but of size 225 mm X 275 mm
All as per item no 99.00 above but of size 225 mm X 175 mm
All as per item no 99.00 above but of size 175 mm X 125 mm
All as per item no 99.00 above but of size 125 mm X 125 mm
Supply and fixing double door TPN DBs 4 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed.
Supply and fixing double door SPN DBs 12 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed.
Supply and fixing double door SPN DBs 8 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed.
Supply and fixing double door SPN DBs 4 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed.
Supply and fixing single door SPN DBs 2 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed.
Supply and fixing MCB SPN 5 to 40 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed.
Supply and fixing MCB SPN 40 to 63 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed.
Supply and fixing MCB SP 240 volts 5 to 32 Amps, 10 KA breaking capacity, 'C' type including connection with suitable size aluminium / copper lugs complete all as specified and directed.
Supply and fixing MCB TPN 50 to 63 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed.
Refixing MCB TPN/SPN/SP any size, capacity obtained from item no 39.00 complete all as specified and directed.
Refixing LED tube light fittings any type, wattage and any size obtained from item no 38.00 complete all as specified and directed.
Supply and fixing LED tube light batten box type with decorative end caps suitable single tube 1x 18/20 watt T8 lamps type complete with both end bi-pin holder and all accessories internally pre wired and fixed to wall/ceiling incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified.
supply and fixing LED tube rod 18/20 watt 230 volt T8 type complete with electric electronic driver incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified.
Supply and fixing LED Batten light Aluminium Housing 18/20 watt 230 volt T8 type complete with electric electronic driver incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified.
Supply and fixing LED batten tube light fitting 1x 10 watt 230 volt wall/ ceiling mounted luminaire with polycarbonate hoiusing and integrated electronic driver with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified.
Supply and fixing Wall light fixture lantern made up of metal with chrome finish and white colour diffuser complete with LED 9 watt lamp B-22 base including all necessary accessories and connection complete all as specified and directed.
Supply and fixing in repair Energy Savings Long Life 15 Watt 230 Volts 50 Hz, IP20 rating recessed mounting downlight with aluminium housing and heat sink for better thermal performance and morden and minimalist design with flushed diffuser and as per site requirement ceiling cutout fitting for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed.
Supply and fixing in repair Energy Savings Long Life 12 Watt 230 Volts 50 Hz, IP20 rating recessed mounting downlight with aluminium housing and heat sink for better thermal performance and morden and minimalist design with flushed diffuser and as per site requirement ceiling cutout fitting for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed.
Supply and fixing in repair Energy Savings Long Life 18 Watt 230 Volts 50 Hz, IP20 rating recessed mounting downlight with aluminium housing and heat sink for better thermal performance and morden and minimalist design with flushed diffuser and as per site requirement ceiling cutout fitting for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed.
S&F recessed mounting fitting 1 x 36/42 watt ultra modern design Natural white/ Warm white architectural LED luminaire (2X2) feet which provides soft-light and glare free symmetrical illumination suitable for Armstrong / Grid Ceiling including LED driver and 36/42 watt LED for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed.
S & F in replacement Building security LED light luminaire 1X25 W, pressure die cast housing with toghned glass, 240V, efficacy Min 110 Lm/Watt, IP-66, 5 KV external SPD , THD<10%, PF>0.95, CCT-5700K, High power SMD LEDs with LDR sensor working 10 Lm visibility for automatic ON/OFF operation and including cable for connection from celling rose with 1.5 Sqmm 3 Core PVC insulated stranded copper conductor (FRLS) cable including GI bracket medium grade bent to shape etc all as specified and directed.
Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and directed.
M&L for Sub main wiring two run single core PVC insulated unsheathed cable FRLSH 1100 volts grade, 6.00 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including one run of 4.00 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor cable connected to earth dolly complete all as specifed and directed.
All as peritem No 126.00 but with two single core 4.0 Sqmm size with 2.5 Sqmm cable as earth conductor complete.
All as peritem No 126.00 but with two single core 2.5 Sqmm size with 2.5 Sqmm cable as earth conductor complete.
All as peritem No 126.00 but with two single core 1.5 Sqmm size with 1.5 Sqmm cable as earth conductor complete.
M&L for Rigid non metallic PVC conduit ISI marked, medium grade, inclusive of all fitting such as tees,bends. Junction boxes, elbows saddles. Pipe hooks,couples and lock outs etc 25 mm external dia, fixed on surface mounted complete and making good disturbed surfaces in repairs all directed.
M&L for Rigid non metallic PVC casing caping ISI marked, medium grade,not less than 20 mm base size inclusive of all fitting such as tees,bends. Junction boxes, elbows saddles hooks,couples and lock outs etc fixed on surface mounted complete and making good disturbed surfaces in repairs all directed.
M&L for rigid non metallic PVC conduit ISI marked, medium grade, inclusive of all fitting such as tees, bends, junction boxes, elbows saddles. Pipe hooks, couples and lock out etc 20 mm external dia fixed on surface mounted complete and making good disturbed surfaces in repair all as directed
Supply & fixing Sheet metal earth plug, socket, single pole and neutral with single pole MCB 32 Amps 240 volts fixed in repairs complete.
Supply and fixing of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to GI earth strip 25 x 4 mm by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion all as specified and directed.
(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 68,361.00 (refer Sch of credit). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’
M/S GURUNG CONSTRUCTION (BID ID -3517443)
M/S K M CONSTRUCTION (BID ID -3519059)
PRADIP KUMAR BOSE (BID ID -3518369)
M/S KAR CONSTRUCTION (BID ID -3519066)
UNIVERSAL CONSTRUCTION (BID ID -3518958)
NABIN CONSTRUCTION AND CO. (BID ID -3519420)
NAYAK BROTHERS (BID ID -3519483)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.32 MB
TENDER8764.pdf
Tender Documents • 0.82 MB
BOQ_834407.xls
BOQ • 0.36 MB
Download all tender documents and submit your bid