SPECIAL REPAIRS TO CERTAIN SMQs (BLOCK NO P 11 AND P 12) AT AKASH VIHAR CAMP AT ASTE UNDER GE (AF) MARATHAHALLI

Amount

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing servicable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust, Brushing neat cement slurry with 3.0kg of cement per sq. metre etc complete all as specified and directed.

M & L coloured non skid ceramic tiles 7 to 8mm thick area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed CM 1:4, 15mm thick complete all as specified and directed.

M & L coloured non skid ceramic tiles 7 to 8mm thick area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in skirting etc, and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat 10mm thick CM 1:3 on vertical surface such as skirtings, dados risers to steps etc complete all as specified and directed.

M & L for Glazed ceramic tiles in vertical surface for toilet & Kitchen, 450mm x 350mm x 7 mm thick, dark coloured,on wall surfaces including designer pattern, set and jointed in neat cement slurry and pointed in white cement with pigment to match over 10 mm thick rendering in CM 1:3 all as specified and as directed.

M & L Non Skid ceramic tiles, 300mm x 300mm x 7mm thick, light coloured, in floor with 15 mm thick screed or bedding layer in cement mortar CM 1:4 for laying floor finishes, set and jointed in neat cement slurry and pointed in white cement with pigment to match complete all as specified and directed.

Taking down cement plaster on brick/stone wall and ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling of Brickwork or stone/boulder masonry, built in cement mortar/cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L for pre cast cement concrete block masonry with solid block 10 cm thk in width (with plain or interlocking joints as directed) complete, in walls and set in cement mortar 1:6 of PCC 1:3:6 (Type C1) complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:6 on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L, for rendering 10 mm thick in CM 1:3 on concrete surface of ceiling to be finished even and smooth surfaces without using extra cement complete all as specified and directed.

Refixing of wooden shutters in same opening exceeding 1Sq.m. and not exceeding 2 Sqm each complete all as specified and directed. (Note :`Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.) etc complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons incl granite slab in kitchen platform Laid, bedded and pointed in any mortar etc complete all as specified and directed.

M&L for Granite slab 20mm thick (of any type) work(table rubbed and polished)in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Providing edge moulding to 18-20mm thick Granite stone of counter vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for PCC 1:5:10 type E2 (using 40 mm graded stone aggregate), in as mass concrete/ sunken floors complete all as specified and directed.

M & L for 40mm thick cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) in floor, finished even and smooth with out using extra cement compete all as specified and directed.

M & L for 75mm thick Cement concrete type C2, 1:3:6 (using 40mm graded stone aggregate) in plinth protection, pavings, finished even and smooth with out using extra cement, incl making joints and filling gap with bitumen mastic complete all as specified and directed.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid , set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed CM 1:4, 20mm thick including rubbing and polishing of stone slab complete all as specified and as directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick,industrial type coloured, Pre polished,set, jointed and pointed in neat cement slurry with grey cement and pigments in floors incl. 20mm thick screed bedding layer in CM 1:4 complete all as specified and directed.

M&L for Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, mixed with water proofing liquid and finishing the surface even and smooth without using extra cement, complete all as specified and directed. NOTE: Water proofing liquid shall be measured and paid separately under respective item of this schedule.

S&F in repairs Harrison rails (curtian rod),mild steel, chrominum plated with fixing brackets stops, roller etc complete all as specified and directed

Taking down wooden/PVC shutters exceeding 1Sq.m. and not exceeding 2 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame ) wooden exc 1.5 sqm but not exceeding 4.0 Sqm each complete all as specified and directed.

M & L cutting holes to brick wall built in cement mortar exc half brick but n.exc one brick for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required.

M & L cutting holes to stone wall built in cement mortar exc one brick but n.exc two bricks for inserting outlet trap and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required.

S&F for Second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete

M & L for 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars),II nd class hard wood, divided into squares with plain, chamfered or rounded, mitered and rebated sash bars in windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.20 (b) any numbers all as specified and as directed.

M & L 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with lipping frame to match. complete all as specified and directed.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

M & L for Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelaminated PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S & F powder coated aluminium (min thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or morerebates including joining cleat for fixing etc. complete all as specified and directed.

Dismantling structural steel work including doors, gates ,rolling shutters etc

S & F providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,concealed sliding lock all complete as per architectural drawings and the directions of Engineer-in-charge complete all as specified

S&F Box type Steel Windows/Ventilators double side shutters (Windows side hung type , Ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm , windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified incl 12mm square guard bars/grill welded with steel frame (100c/c horizontically) all as specified and directed by Engineer-in-Charge. NOTE: (i) Payment under this item will be make combined for steel frames, steel shutters and Guard bars/Grill, However unit rate quoted shall deemed to include cost of beading, fittings such as handles, hinges,Telescopic stays, locking arrangements and fixing of glass and wiremesh etc. (ii) Supply only 4 mm thick sheet glass and stainless steel wire mesh shall be measured and paid separately. (iii) Weight of Grill/ Guard Bars, handle, hinges and locking arrangements shall not be accounted separately for payment purpose .

S & F 18 /19 mm thick Block boards, grade 2 quality,Exterior grade,decorative type with decorative face veneer on both sides, fixed with screws to timber frame-work, fixed with screws to timber frame work, all as specified and directed.

S & F Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails all as specified.

M & L for Framed brackets of rolled mild steel angles or Tee sections, conforming to Fe 310-O, cut to shape, drilled and counter sunk for screws, including bending, welding as necessary, all as specified and directed.

S&F Piano hinges 30mm width of flaps(when open) mildsteel, bright finish or electro galvanised complete all as specified and as directed by Engr-in-charge.

S & F Aluminum powder coated handles 75mm long all as specified and directed.

S&F 75mm long Hasp and staple, aluminium anodised, including bolt to hinge plate and fixed with screws all as specified and directed.

S & F in repairs stainless steel sinks with drainage board made of stainless steel 1.00mm thick stainless steel sheet of grade 304 for kitchen fixed with plugs, washers, overall size 915mm x 460mm with bowl size 405mm x 355mm x 178mm including chromium plated waste coupling of 32mm dia, including fixing cantilever brackets, PVC waste pipe 32mm dia and 600mm long (minimum), complete all as specified and directed.MAKE:- Cat No. SSSBSD-52 of Bluestar or techno-commercially equivalent model in Nirali / Anjali / Jayna / Diamond / M-Brand / Prince

S & F PVC waste pipe, 32 mm dia, 750mm long, suitable for Kitchen sink,fixed in repairs all as specified and directed. Make :Prayag. Cat no. 3272 or equivalent

Taking up or down 15mm bore steel tubing and connection including cleaning for refixing or removal to store all as specified and directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for refixing or removal to store all as specified and directed.

S&F 20mm bore(OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and directed.

S&F 25mm bore(OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and directed.

S &F Bib taps, brass chromium plated, fancy type, long body, screwed down, screwed for 15mm bore iron pipes or brass ferrule, fixed in repairs, all as specified and as directed.Make. Prayag. cat no.6508 or equivalent

S&F fancy type angle cock of brass chromium plated with ling shank screwed for iron pipe and fixed (15mm minimum weight 90gms) 15mm dia fixed to iron pipe in repairs. Make. Prayag. cat no.6510 or equilent

S&F in repairs Pillar taps brass chromium plated, fancy type, foam flow, screwed down high pressure screwed for iron pipe 15mm bore, fixed in repairs, all as specified and as directed.Make. Prayag. cat no.6502 or equilent

S&F 2 in-1 Bib tap, long shank with flange,15mm size fixed in repairs all as specified and directed ..Make. Prayag. cat no.6512 or equilent

S&F Bib tap, with flange, 15mm size fixed in repairs all as specified and directed ..Make. Prayag. cat no.6506 or equilent

S&F fancy type concealed stop cock with flange of brass chromium plated with long shank screwed for iron pipe and fixed 15mm dia fixed to iron pipe in repairs. Make. Prayag. cat no.6520 or equilent

S & F CP Swivel overhead shower (ABS chrome) of with brass arm 150mm (with flange) for fixing with 15mm pipe all as specified and directed. Make. Prayag. cat no. BOS-11 or equilent

S&F PTMT towel rod 600mm long(min wt 190gms), fixed in repairs, all as specified and as directed.

S & F corner glass assembly consists of 5.5mm thick sheet glass shelf 12cm wide fixed with and including chromium plated brass screws and wooden/plastic cleats with CP bracket, guard railing 60cm long, fixed in repairs, all as specified and directed.

S & F in repairs Vitreous china wash hand basin,vitreous china, white, flat back, of size 630x450mm, including pedestal with plug and porcelain stopper, brackets, waist coupling brass CP 32mm all as specified and directed.

S & F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gm) all as specified and directed.

S & F in repairs waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms) for 32mm dia all as specified and directed.

S & F Stainless steel gratings with frame, 127 mm dia, with hole for waste pipe connection as in repairs all as specified and directed.

S&F Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to drain (or out going pipe) and to flushing pipe, anti - syphonage pipe etc., including making good to floor complete fixed in repairs all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white, complete with trap, fixed to floor with fixing bolts and seat cover, including connection to drain (or out going pipe) and to flushing pipe, anti - syphonage pipe etc., including making good to floorcomplete, fixed in repairs all as specified and directed.

S&F Plastic water closet seat cover any colour, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device fixed all as specified and directed. (Note: Seat cover make should be same as of WC make)

S & F PVC connections 450mm long between ends with 2 Nos. brass nuts and washers, 15mm size, fixed in repairs, all specified and as directed.

S & F PVC 10 Ltr capacity flushing cistern white, inlet, ball valve, float and handle on existing brackets and jointing with existing flush pipe and making good to the disturbed surfaces including dismantling of unserviceable flushing cistern complete all as specified and directed.

S&F Health faucet, CP, with 1 metre flexible tube with wall hook, all as specified and directed.Make. Prayag. cat no.BEA-97 or equivalent.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, with 150mm long cover plate including provision of vulcanised rubber piece, fixed in repairs, complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staple, complete all as specified and directed.

S & F in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staple, complete all as specified and directed.

S & F 150 mm size aluminium powder coated barrel tower bolts of extruded section complete all as specified and directed.

S & F extruded aluminium handles 100mm long in repairs fabricated type anodised complete all as specified and directed.

S & F extruded aluminium handles 150mm long fabricated type anodised complete all as specified and directed.

S&F Aluminium, barrel tower bolt of extruded section, 100mm long in repair complete all as specified and directed.

S&F in Aluminium alloy, anodised, 300mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy fixed in repairs complete all as specified and directed.

M & L 100 mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B 21 all as specified and directed.

S&F 300 mm ordinary MS rat tail rod pattern springs including roller and roller plate in repairs complete all as specified and directed.

Hacking out old broken glass of any thickness and description from wooden/ metal frames fixed with wooden beads/ putty complete all as specified and directed.

S & F 4mm thick sheet glass, ordinary quality, glazing with wooden beads/ oil putty, in square not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S & F 4mm thick Figured glass, pin head type and glazing with oil putty in square not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S & F pressed steel frames of size 105 x 60mm x 1.25 mm thick for door with one or more rebates, including necessary fixing lugs, hinges lock strike plate etc complete all as specified and as directed.

M & L for cement concrete 1:3:6 type C1 (using 20mm graded aggregate) as in filling holdfasts frames complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed with wall including necessary fixing cleats/ clamps, fixed in repairs complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall including necessary fixing cleats/ clamps complete all as specified and directed.

S&F 50 mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F PVC bend of 110 mm dia complete all as specified and directed.

S&F PVC bend of 110 mm dia with access door complete all as specified and directed.

S&F PVC bend of 75 mm dia complete all as specified and directed.

S&F PVC bend of 75 mm dia with access door complete all as specified and directed.

S&F PVC (SWR) branch piece, double(double Y) equel or un equel fixed to 110mm bore of pipes with access door all as specified and directed.

S&F PVC (SWR) vent cowl fixed to 110mm bore of pipes all as specified and directed.

All as per item No.93 here in before but 75mm bore.

PVC (SWR) 'P' trap suitable for 110mm/100mm bore of pipes complete all as specified and directed.

M&L for PVC (SWR) floor trap75mm dia., plain with grating including jointing with solvent cement complete all as specified an directed.

M&L applying 1mm thick BRUSHBOND RFX GREY or equivalent using stiff brush or trowel to the plastered surface in sunken floor complete all as specified and directed.

M & L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and directed.

Removing by cutting/up rooting plant/tree under surface of wall/celling including making good the damage portion with cement mortar 1:3 or concrete 1:2:4 type B1 (using 20 mm graded aggregate) complete all as specified and directed (Note : Approx height of building 10m)

M & L Raking out joints/ pointing to Stone masonry or brick-work built in cement lime mortar in single detached joints for flashing, etc.complete all as specified and directed (Note: Approx height of building 10m)

M & L Flush pointing to block squared rubble masonry, coursed or uncoursed in CM 1:4 complete all as specified and directed. (Note : Approx height of building 10m)

S & F Gate and shutter hooks and eyes 150mm mild steel in repairs complete all as specified and directed.

M & L for preparing previously untreated wood and wood based materials of any description over 10 cm width / girth and applying two coats of Synthetic Enamel paint over one coat of pink primer complete all as specified and directed.

M & L for one coat of white wash on old decorated surfaces of ceilings including necessary preparation of surfaces complete all as specified and directed.

M & L for three coat of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces complete all as specified and directed.

M & L for Complete removal existing treatment on walls washing, rubbing down and stopping of existing treatment applying two coats oil bound emulsion distemper over a coat of primer over a coat of wall putty 1mm thick using rollers to match with existing surface complete all as specified and directed.

M & L for One coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces complete all as specified and directed.

M & L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces complete all as specified and directed.

M & L for Two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm width or girth including necessary preparation of surfaces complete all as specified and directed.

M & L for Two coats of cement based paint on walls, pillasters, cornices, etc., including necessary preparation of old finished surfaces complete all as specified and directed.

Preparing the newly plastered surfaces of ceiling and applying two coat of cement based paint complete all as specified and directed.

M & L PVC (SWR) floor trap 75 mm dia of outlet , plain with grating including jointing with solvent cement fixed in repair complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregates) as in slab supported on wall, beam ,roofs, landing, chajja, shelves etc complete all as specified and as directed.

M&L for mild steel bars 10 mm dia and over TMT bar, cut to length bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs landing and similar work not exc 200 mm thick, with supports and rough finished surfaces of concrete complete all as specified and directed.

M & L for removing unserviceable building materials etc. (other than spoil) to a distance of 5km or under, beyond the lead included in the rates, including loading and unloading at the destination.

Taking down carefully copper/aluminium point wiring of any type of batten or conduit (Light, Fan, Socket or power) complete removing material from site and making good the disturbed surfaces of walls, roofs etc including two coats of white/colour washing/distempering etc to match the existing complete all as directed by Engr-in-Charge.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls complete all as specified and directed.

Taking down / refixing geyser any rating and any size kept in store with out damaging in safe custody and refixing same in postion after repair work complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Dismantling and taking down fluorescent light fitting single /double tube any wattage /any size complete all as specified and directed.

Fixing only of LED light fittings 1x20 watt removed good working condition fittings kept in store with out damaging in safe custody and re-fixing the LED fittings after repair work complete all as specified and directed.

Fixing only of LED light fittings 1x10 watt removed good working condition fittings kept in store with safe custody and re-fixing the LED fittings after repair work complete complete all as specified and directed.

Refixing of MCB SP 6 to 32 Amps and making good after civ works as per exisiting site requirement complete all as specified and directed.

Refixing of MCB SPN of 32 Amps and making good after civ works as per exisiting site requirement complete all as specified and directed.

Refixing of DB SPN 8 Way and making good after civ works as per existing site requirement complete all as specified and directed.

M & L in repairs of socket 5/15 Amps after civ works as per existing site requirement complete all as specified and directed.

M & L in repairs of Fan regulator of any size after civ works as per existing site requirement complete all as specified and directed.

M & L in repairs of switch piano of 5 Amps after civ works as per existing site requirement complete all as specified and directed.

M & L in repairs of switch piano of 15 Amps after civ works as per existing site requirement complete all as specified and directed.

M & L point wiring with 1.5 sqmm nominal cross sectional area, single core, 1100 Volts grade, stranded, PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 25 mm dia or higher, medium grade complete with and including all PVC conduit accessories/fittings, brass screws, washers etc, Sunk Zinc coated pressed steel terminal boxes including all cutting/chases etc in walls, making good to walls, ceiling etc including two coats of white/colour washing/ distempering etc to the disturbed surfaces to match the existing with 3 mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed by Engr -in -charge for One light point /fan point controlled by one way switch.

All as per item No. 134 but one 5 Amps socket point on same board with other switches

All as per item No. 134 but one 5 Amps socket point on independent board.

All as per item No.134 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board .

S & F switch piano flush type, 05/06 Amps single pole, one way 240 volts in replacement of old u/s complete all as specified & directed

Supply & fixing of socket outlet 3 pin, 05/06 Amps (2-in-1 Multipurpose) flush type 240 volts in replacement of old u/s complete all as specified & directed.

Supply & fixing of socket outlet 3 pin, 15/16 Amps (2 -in-1 Multipurpose) flush type 240 volts in replacement of old u/s complete all as specified & directed.

Supply & fixing switch piano flush type, 15 /16 Amps single pole, one way 240 volts in replacement of old u/s complete all as specified & directed

Supply & fixing of ceiling rose surface three terminals in replacement of old u/s complete all as specified & directed.

M & L for sub main wiring complete with two runs of 4 Sqmm single core FRLS grade PVC insulated unsheathed cable 1100Volt grade multistranded copper conductor drawn through and including PVC conduit and accessories in surface of wall, roofs etc with one run of PVC insulated copper conductor 4 Sqmm single core as earth continuity conductor connected with earth dolly and mains complete all as specified and directed. Note : Two runs of cable, one PVC conduit and one run of earth continuity cable shall be one unit.

Taking down ceiling fan/Exhaust fan, sealing the cable ends dismantling the fan blade kept in safe costody complete all as specified. Note: (a) Servicing and Spares will be measured and paid seperately .

Supply only GM bush of ISI marked suitable for ceiling fan of size 1200 / 1400mm sweep.

Supply only ball bearing suitable for ceiling fan of 1200 /1400mm sweep.

Supply only capacitors 2.5 MFD of the fan.

Supply only capacitors 4.0 MFD of the fan.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan retrieved against item No. 144 herein before.

M&L for Painting of ceiling fans/ exhaust fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan retrieved against item No. 144 herein before.

PRAGATHI BUILDERS

K T ASSOCIATES

B5BUILDING SOLUTIONS